1995 Dodge Dakota Differentials

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for AMC Model 35 differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits AMC Model 35 with 27 spline axles
• Includes carrier bearings and races and “super” carrier shim kit

Product Features:

• MINI INSTALL KIT CHRYSLER 9.25 9 1/4″

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 2000 to early 2003 Chrysler 8.0″ IFS
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Standard Open notched cross pin shaft for 9.25″ Chrysler.

Product Features:

• Cross pin shaft
• Fits Chrysler 9.25″
• Standard open carrier only
• Notched

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Chrysler 8.25″ with 29 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

M804049 set-up bearing (one bearing). No return.

Product Features:

• Set up bearing
• Fits HM804049 pinion bearing
• Easily slips on and off pinion journal to allow for pinion depth adjustment

Product Features:

• Brand may vary by location

Demand genuine Spicer. Dana design, engineering, testing and manufacturing processes all work in conjunction with one another to ensure unparalleled performance that non-genuine parts simply cannot deliver.

Product Features:

• Genuine OE quality. Tested and proven.
• Built to meet OE standards set by Dana.
• Tested and validated to rigorous OE specifications.
• Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace.

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

This differential ring and pinion directly replaces the original equipment on specific vehicle years, makes and models.

Product Features:

• Direct replacement – this ring and pinion set matches the fit and function of the original components on certain vehicle applications
• Effective fix – eliminates grinding and whining from failed original bearings
• Thoroughly tested – vehicle try-on testing and rigorous quality control measures ensure longevity
• Trustworthy quality – backed by team of designers and engineers in the United States

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Valvoline SAE 75W-140 Full Synthetic Gear Oil provides the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Engineered to outperform, our formulation provides exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity and wear resistance, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. It’s recommended for conventional rear axles and transmissions requiring EP gear lubes under high speed, high load, high torque and high horsepower conditions.

Product Features:

• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -22F to 390F degrees
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM88610 race
• All steel construction

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Sealed Power parts provide innovative designs, use leading-edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Product Features:

• Steel-backed Babbitt lining material
• Used in automotive and high-performance
• Babbitt is designed to perform under extreme loads without damaging other engine parts
• Babbitt is more environmentally friendly than other material
• ISO & QS certified manufacturing

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

• Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

Side gear thrust washer for 7.25″ Chrysler.

Product Features:

• Side gear thrust washer kit
• Fits Chrysler 7.25″

Bolt/screw for adjuster lock for Chrysler 7.25″, 8.25″, 8.75″, 9.25″.

Product Features:

• Side adjuster lock bolt
• Fits Chrysler 7.25″, 8.25″, 8.75″ and 9.25″

Crush Sleeve for Model 35, Chrysler 7.25″, 8.25″ Ford 8″ & GM 7.75″. Approx 0.495″ long.

Product Features:

• Crush sleeve for AMC Model 35, Chrysler 7.25″ and 8.25″, Ford 8″ and GM 7.75″
• 0.495″ tall

This differential cover plug is designed to match the fit & function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

• Direct replacement – this differential cover plug matches the fit and function of the factory part on specified years, makes and models.
• Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 2001 to 2009 Chrysler 9.25″ rear
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Product Features:

• Pinion nut
• Fits Chrysler 7.25″, 8.0″, 8.25″, 9.25″ and 8.75″ with 29 spline pinion