1995 Chevrolet Caprice Performance Engines

Essential 1995 Chevrolet Caprice Performance Engines

B & M – Holeshot 3600 (Part No.20425)

Holeshot 3600

from

$825.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
  • Dual Pattern Drive Lugs
  • New Turbine Hub
  • New Springs/Rollers In Stator
See More

B & M – Holeshot 2400 (Part No.70441)

Holeshot 2400

from

$709.99
Holeshot 2400 for GM 1998 to 2002 4L60E Camaro and Firebird with an LS1 engine Application: GM 1998 to 2002 4L60E Camaro and Firebird with LS1 A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benef

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

from

$65.99
Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

from

$151.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Non-Rotator Style: Dyno Tested and Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

Edelbrock – Pushrod Set for S/B Chevy (Part No.9629)

Pushrod Set for S/B Chevy

from

$187.99


Product Features:
  • Case-Hardened Tubing
  • Surface Hardening
  • Welded Ends
  • 0.3125 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Edelbrock – Pushrod Set for S/B Chevy (Part No.9646)

Pushrod Set for S/B Chevy

from

$203.99
Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:
  • 7.25 in. Length
  • 0.312 in. Diameter
  • 4130 Chromoly Steel Material
  • Black Oxide Finish
  • Made In The USA
See More

Edelbrock – Cylinder Head Gasket Set for Chevrolet (Part No.7310)

Cylinder Head Gasket Set for Chevrolet

from

$58.99
Product Features:
  • 4.125 in. Cylinder Bore Diameter
  • 0.039 in. Thickness
  • 8.7cc Volume
  • Charcoal Color
  • Two Piece Configuration
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1004)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$52.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Intake Manifold replacement base to top gasket (Part No.6999)

Intake Manifold replacement base to top gasket

from

$17.99
Replacement gasket for top to bottom. See PN(7110) complete. PN(7067) bottom. PN(7032) top. Includes base and top for intake manifold PN(7110).

Product Features:
  • Replacement Gasket for Top to Bottom
  • See PN[7110]Complete; PN[7067]Bottom; PN[7032] Top
See More

Edelbrock – Victor Jr. 23 Degree Tall Intake Manifold Small-Block Chevy (Part No.2999)

Victor Jr. 23 Degree Tall Intake Manifold Small-Block Chevy

from

$463.99
Edelbrock part #2999 Victor Jr. 23 degree Tall intake manifold provides maximum performance for engines with standard port location, iron and aluminum cylinder heads. This versatile manifold is excellent for many applications from high-performance’s stree

Product Features:
  • Race Winning Design for all Types of Competition
  • Single Plane Maximizes Torque and Horsepower
  • For Performance in 3500 to 7500 RPM Range
  • Exit Ports Closely Match Unported GM Bowtie Heads
  • Ports Match GM PN[14011058/14011034/10134392]
  • Best for Classes Restricting Porting of Intakes
  • Features 1 in. Taller Carb Pad than PN[2972]
See More

Mr. Gasket – Engine Sealing (Part No.6560)

Engine Sealing

from

$499.99
Manufactured from cellulose and nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement, high performance street, drag race and oval track.

Product Features:
  • Made of high temp silicone or nitrile blend rubber
  • Torque limiters to prevent over tightening
  • One piece molded rubber
  • Fits left and right hand dipsticks
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1800)

PERFORMANCE OIL PAN GASKET SET

from

$18.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Intake Bolt Kit (Part No.5003)

Intake Bolt Kit

from

$75.99
Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:
  • Chrome plated
  • Grade 8
  • 12-point head
  • AN washers with no exposed shoulder for a professional appearance
See More

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers

from

$17.49
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:
  • Zinc plated to resist corrosion and provide a clean professional appearance
  • Made from Grade 5 steel for strength and durability
  • Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
  • Allen (socket) Head
  • Zinc Plated For Protection
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Performer Series Retainer (Qty 16)

from

$99.99
Product Features:
  • Use W/ Valve Springs Part #5703, 5794
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

Performer Series Retainer (Qty 16)

from

$95.99
Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:
  • Valve Spring Retainers for Use OE Cast Iron Heads
  • Superior Quality Heat-Treated Steel
  • Machined for Strength with Black Oxide Finish
  • Finish Ensures Rust and Corrosion Protection
See More

Mr. Gasket – Intake Gasket (Part No.143)

Intake Gasket

from

$42.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Die-cut for an excellent fit
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
See More

Edelbrock – Intake Manifold Gasket for 1965-1990, Mark IV B/B Chevy, Rec Port (Part No.7208)

Intake Manifold Gasket for 1965-1990, Mark IV B/B Chevy, Rec Port

from

$30.99
Edelbrock part #7208 Intake Gaskets for 1965-1990, Mark IV 396-402-427-454-555, Rectangular Port 6 Bolt Flange with no crossover allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, an

Product Features:
  • 1.82″x2.46″
  • Rectangular Port Style
  • .060″ Thick
  • Two Piece Configuration
  • Composite Material
See More

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 9 Piece Set (Part No.1212)

Lower Intake Manifold Gasket Set: 9 Piece Set

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
  • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
  • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
  • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
  • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
See More

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7810)

Performer-Link Adjustable True-Roller Timing Chain Set

from

$74.99


Product Features:
  • Solid Bushing Chain Resists Stretching
  • For Use with Stock or Edelbrock Camshafts
  • Stressproof Steel Crank Gears
  • 3 Keyway Setting Points To Ensure Accurate Timing
  • True Bearing Surface Rolls with the Sprockets
See More

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Advance And Retard Cam Bushings

from

$42.49
With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:
  • Advance the cam for increased torque and horsepower
  • Tune your powerband for more end torque or increase top end horsepower
  • Includes (4) offset bushings and (1) 0 degree bushing
  • Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
  • Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
  • Increase Top-End Horsepower
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1074)

Ultra Seal: Competition Screw-In Rocker Arm Studs

from

$85.09
Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Prevents Stud Flexing
  • Black Plated Finish
See More

Competition Cams – MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST (Part No.1412-16)

MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST

from

$213.99
These Magnum Roller Rocker Arms for Chevy V8 265-400 and V6 200-262 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.52 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed

Product Features:
  • Roller tip reduces friction while stiff design and superior ratio accuracy yield more effective valve lift
  • For applications with less than 350 lbs. of open spring pressure
  • Constructed from 8620 chromemoly steel, a superior material that will not flex and ensures maximum lift
  • Ultimate street roller rocker arm designed for serious performance enthusiasts
See More

Mr. Gasket – Ultra Seal: Sure-Lock Rocker Arm Nuts (Part No.920G)

Ultra Seal: Sure-Lock Rocker Arm Nuts

from

$64.19
These are high quality nuts with allen set screws to provide you with that positive lock needed for Race or original equipment Rocker Arms.

Product Features:
  • They Are Zinc Dichromate Plated Steel
  • They Have Black Oxide Coated Set Screws
  • Keeps Rocker Arms Positively Locked
  • (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
  • Includes Locks and Hex Wrench
  • Shank O.D. .603″
See More

Competition Cams – Thumpr 227/241 Hydraulic Flat Cam (Part No.11-600-4)

Thumpr 227/241 Hydraulic Flat Cam

from

$542.99
HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.

Product Features:
  • HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.
  • 279/296 Advertised Duration, 227/241 Duration @ .050″, .498″/.483″ Lift, 107 Lobe Separation
  • Valve spring upgrade required
See More

Competition Cams – CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA (Part No.12-601-8)

CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA

from

$522.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Competition Cams – Xtreme Energy 218/224 Hydraulic Flat Cam (Part No.42-222-4)

Xtreme Energy 218/224 Hydraulic Flat Cam

from

$548.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

1995 Chevrolet Caprice Performance Engines

Maybe you’re in the middle of a full rebuild of that 1995 Chevrolet Caprice. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 20 different Performance Engines in our inventory ranging from $27.49 to $709.99. That means you can find the exact parts or products you need to keep that 1995 Chevrolet Caprice running smoothly.

Performance Engines are only as good as their brand. We stock 5 different brands to make sure you have plenty of trusted parts to choose from for your 1995 Chevrolet Caprice. Edelbrock, FEL-PRO Performance, and Mr. Gasket are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1995 Chevrolet Caprice, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.

So if you’re in the market for aftermarket Performance Engines to keep your 1995 Chevrolet Caprice rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1995 Chevrolet Caprice Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1995 Chevrolet Caprice demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your Caprice the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

FAQs for 1995 Chevrolet Caprice Performance Engines

What are the most purchased Performance Engines for the 1995 Chevrolet Caprice?

Out of 20 Performance Engines for the 1995 Chevrolet Caprice, the most popular in our inventory are:
Lower Intake Manifold Gasket Set: Includes Sealer, 3 Piece Set
from $36.49
(1)
Lower Intake Manifold Gasket Set: Includes Sealer, 3 Piece Set
Performance Engine Intake Manifold Gaskets
Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads
from $65.99
This product is not rated
Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads
Performance Engine Valve Springs
Ultra Seal: Oil Pan Gasket
from $42.49
This product is not rated
Ultra Seal: Oil Pan Gasket
Performance Engine Oil Pan Gaskets