1994 Nissan Sentra Belts and Hoses

Essential Belts and Hoses for 1994 Nissan Sentras

Gates – Premium Molded Coolant Hose (Part No.22971)

Premium Molded Coolant Hose

from

$26.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 25.5" Long, 1.34" Diameter (Part No.E72779)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 25.5" Long, 1.34" Diameter

from

$27.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13.50" Long, 1.25" Diameter (Part No.C71832)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13.50" Long, 1.25" Diameter

from

$23.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Gates – Straight Heater Hose: EPDM, Direct Fit, 1" Inside Diameter (Sold by foot) (Part No.28413)

Straight Heater Hose: EPDM, Direct Fit, 1" Inside Diameter (Sold by foot)

from

$3.99
Premium hose constructed for long service life.

Product Features:
  • Good resistance to high temperatures for extended periods of time, which prolongs service life
  • Meets SAE 20R3 Standard Wall Class D-2 requirements
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • CAUTION: Do not use for fuel or oil transfer applications
  • CAUTION: Do not use for fuel or oil transfer applications
  • PLEASE NOTE: Item is priced and sold by the foot. See store for details.
See More

Original Equipment – Emission Hose (Part No.B7002234900OEA)

Emission Hose

from

$9.65
Emission Hose

Dayco – Aramid Cord Poly Rib Belt Serpentine Belt; 48.03 Long, 6 Rib Count (Part No.A060480)

Aramid Cord Poly Rib Belt Serpentine Belt; 48.03 Long, 6 Rib Count

from

$23.99
The Dayco poly-V aramid belt is engineered to maintain a quiet, vibration-free belt drive system, especially for higher output OE engines that require an aramid belt. Unlike polyester-corded belts, this aramid cord belt is designed to resist the expected elongations, especially during high accessory loading. This unique feature of length stability and minimal stretch aids in difficult drives where span vibrations and tensioner movements are excessive. The Dayco aramid cord poly rib belt is built with Dayco’s specially designed EPDM rubber compounds to resist cracking and perform better under extreme temperature ranges.

Product Features:
  • Designed for applications with an OEM aramid belt and is specifically helpful for those with noise, vibration or harshness issues, or in-drive systems in which tensioner take-up is minimal
  • Length stability resists excessive span vibrations or tensioner movements
  • Features special compounds that resist cracking and perform well under intense engine temperatures 
See More

Driveworks – Poly Rib Belt Serpentine Belt; 88.58 Long, 6 Rib Count (Part No.885K6)

Poly Rib Belt Serpentine Belt; 88.58 Long, 6 Rib Count

from

$23.99
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
See More

Dayco – Poly Rib Belt Serpentine Belt; 71.06 Long, 6 Rib Count (Part No.5060710)

Poly Rib Belt Serpentine Belt; 71.06 Long, 6 Rib Count

from

$61.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)

Metal Line Kit for Engine Oil Coolers

from

$87.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:
  • Metal line kit
  • For use in engine oil cooler applications
  • Routes oil lines past exhaust manifolds
  • Provides protection where standard hoses can fail
See More

Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)

1/2" x 12' Engine Oil Cooler Hose

from

$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:
  • Engine oil cooler hose
  • Size: 1/2″ x 12′
  • Designed for engine oil applications
  • 12′ hose length accommodates most applications
See More

Dayco – Serpentine Idler/Tensioner Pulley; Steel, 82mm Dia., 27mm Width, Smooth (Part No.89148)

Serpentine Idler/Tensioner Pulley; Steel, 82mm Dia., 27mm Width, Smooth

from

$33.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear & tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.

Product Features:
  • Designed for the majority of automotive vehicle applications on the road today.
  • High-quality materials help resist wear and improve belt life
  • Features premium lubricated bearings to extend service life
  • Meets or exceeds OE quality
See More

NSK – A/C Belt Tensioner (Part No.R1088124212NSK)

A/C Belt Tensioner

from

$82.06
A/C Belt Tensioner

Dayco – Serpentine Idler/Tensioner Pulley; Steel, 70mm Dia., 27mm Width, Smooth (Part No.89052)

Serpentine Idler/Tensioner Pulley; Steel, 70mm Dia., 27mm Width, Smooth

from

$20.79
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.

Product Features:
  • Designed for the majority of automotive vehicle applications on the road today
  • High-quality materials help resist wear and improve belt life
  • Features premium lubricated bearings to extend service life
  • Meets or exceeds OE quality
See More

Gates – Premium Molded Coolant Hose (Part No.22537)

Premium Molded Coolant Hose

from

$37.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.31" Diameter (Part No.E72407)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.31" Diameter

from

$21.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Gates – Premium Molded Coolant Hose (Part No.21029)

Premium Molded Coolant Hose

from

$17.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 12 Inch Length (Part No.88438)

Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 12 Inch Length

from

$12.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 36 Inch Length (Part No.80405)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 36 Inch Length

from

$21.29
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • Meets Type EC electro-chemical requirements as specified in SAE J1684
See More

Original Equipment – Bypass Hose (Part No.G2020124329OEA)

Bypass Hose

from

$8.73
The Original Equipment bypass hose is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:
  • OEM-Equivalent
  • Inner linings are resistant to electrochemical cracking
  • High strength and resistance to oil, mud, salt, road debris, and ozone
  • Resistance to distilled water and water ethylene glycol mixtures
  • Resistance to air temperatures of up to 125C
See More

Gates – Premium Molded Coolant Hose (Part No.21942)

Premium Molded Coolant Hose

from

$17.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 12 Inch Length (Part No.87620)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 12 Inch Length

from

$12.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 6 1/4 Inch Length (Part No.86804)

Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 6 1/4 Inch Length

from

$12.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 11 Inch Length (Part No.87631)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 11 Inch Length

from

$44.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Premium Molded Heater Hose (Part No.19187)

Premium Molded Heater Hose

from

$15.79
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

ContiTech – Drive V-Belt (Part No.W100033190CON)

Drive V-Belt

from

$18.23
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Polyester fiber tensile members and a ribbed belt design.
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W1000289718BAN)

Multi Rib (Serpentine) Belt

from

$27.77
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W1000101106BAN)

Multi Rib (Serpentine) Belt

from

$24.43
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100026447MBL)

Multi-Rib (Serpentine) Belt

from

$14.13
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
See More

Upgrade your 1994 Nissan Sentra with Top-Quality Belts and Hoses

When it comes to maintaining or upgrading your 1994 Nissan Sentra, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Nissan or enhancing its overall performance, Belts and Hoses are key to keeping your Sentra functioning at its best. At Advance Auto Parts, we offer a wide selection of 58 Belts and Hoses for the 1994 Nissan Sentra, designed to meet your needs without breaking the bank. From Engine Cooling Hose replacements to Radiator Hoses upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Belts and Hoses for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Belts and Hoses for your 1994 Nissan Sentra at great prices. Our Belts and Hoses inventory for this model ranges from just $1.79 to $87.99, with an average price of $24.25. Our 58 Belts and Hoses in stock come from 12 trusted brands, so you’re sure to find the right part for your 1994 Nissan Sentra without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1994 Nissan Sentra, we stock popular OEM and aftermarket Belts and Hoses from top names like Dayco Driveworks, and more. Dayco Belts and Hoses start at just $10.68 and boast an impressive 5 stars average rating from customers. With 327 customer reviews and counting, our 1994 Nissan Sentra Belts and Hoses have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Belts and Hose upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1994 Nissan Sentra is always ready to roll. We’re committed to providing you with everything you need to keep your Sentra in top shape, all in one place. Start shopping confidently below for your 1994 Nissan Sentra!

Best-Selling Engine Cooling Hoses for 1994 Nissan Sentras

Enhance the driving experience in your Nissan with 8 quality Engine Cooling Hose components, starting at $10.68.

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 7" Long, 1.31" Diameter (Part No.B71611)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 7" Long, 1.31" Diameter

from

$15.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 4.38" Long, 1.25" Diameter (Part No.A71356)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 4.38" Long, 1.25" Diameter

from

$23.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Gates – Premium Molded Coolant Hose (Part No.21404)

Premium Molded Coolant Hose

from

$19.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Radiator Hose (Part No.G20001986356DAY)

Radiator Hose

from

$14.64
Radiator Hose

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 6" Long, 1.06" Diameter (Part No.B71748)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 6" Long, 1.06" Diameter

from

$14.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Dayco – Radiator Hose (Part No.G20001163354DAY)

Radiator Hose

from

$17.32
Radiator Hose

Dayco – Radiator Hose (Part No.G20002439128DAY)

Radiator Hose

from

$12.80
Radiator Hose

Dayco – Radiator Hose (Part No.G20001342550DAY)

Radiator Hose

from

$10.68
Radiator Hose

Most Popular 1994 Nissan Sentra Radiator Hoses

Customize your Nissan with 6 Radiator Hoses products like Coolant Hoses and By-Pass Hoses, all priced under $19.49.

Gates – Premium 5/16 X 50 Ft Heater Hose by Gates (sold by each) (Part No.28408)

Premium 5/16 X 50 Ft Heater Hose by Gates (sold by each)

from

$1.79
Premium hose constructed for long service life.

Product Features:
  • Good resistance to high temperatures for extended periods of time
  • Similar to SAE 20R3 Class D-3
  • Temperature rating: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • CAUTION: Do not use for fuel or oil transfer applications.
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 7" Long, 1.06" Diameter (Part No.B71540)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 7" Long, 1.06" Diameter

from

$19.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.06" Diameter (Part No.D71541)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.06" Diameter

from

$12.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Gates – Premium Molded Coolant Hose (Part No.21918)

Premium Molded Coolant Hose

from

$19.29
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:
  • Specifically-engineered materials resist collapse under vacuum
  • Engineered to resist electrochemical degradation, the leading cause of hose failure
  • Pre-shaped to fit and to ensure perfectly sealed conditions
  • EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
  • Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Original Equipment – Bypass Hose (Part No.G2020124329OEA)

Bypass Hose

from

$8.73
The Original Equipment bypass hose is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:
  • OEM-Equivalent
  • Inner linings are resistant to electrochemical cracking
  • High strength and resistance to oil, mud, salt, road debris, and ozone
  • Resistance to distilled water and water ethylene glycol mixtures
  • Resistance to air temperatures of up to 125C
See More

Autopart International Inc – Radiator Hose (Part No.G20003185542API)

Radiator Hose

from

$5.55
Radiator Hose

Top Picks for 1994 Nissan Sentra Pulleys

Upgrade Nissan Sentras with top-quality Pulleys parts, including 2 OEM and aftermarket selections for your 1994 model.

NSK – A/C Belt Tensioner (Part No.R1088124212NSK)

A/C Belt Tensioner

from

$82.06
A/C Belt Tensioner

Litens – Idler/Tensioner Pulley: Direct Fit, Steel, 80mm Diameter (Part No.900451A)

Idler/Tensioner Pulley: Direct Fit, Steel, 80mm Diameter

from

$61.99
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in Canada to the O.E. specified design and meets all performance and durability requirements. This Heavy duty Steel pulley is specifically designed for Nissan applications. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More

In-Demand Heater Hoses for 1994 Nissan Sentras

Select from 8 premium Heater Hoses parts for your 1994 Nissan Sentra, with prices ranging from $12.49 to $29.99.

Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 8 1/4 Inch Length (Part No.86800)

Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 8 1/4 Inch Length

from

$28.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 12 1/2 Inch Length (Part No.86801)

Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 12 1/2 Inch Length

from

$29.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Premium Molded Heater Hose (Part No.18020)

Premium Molded Heater Hose

from

$14.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 6 1/4 Inch Length (Part No.86804)

Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 6 1/4 Inch Length

from

$12.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Premium Molded Heater Hose (Part No.18739)

Premium Molded Heater Hose

from

$27.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Premium Molded Heater Hose (Part No.18021)

Premium Molded Heater Hose

from

$23.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 10 Inch Length (Part No.87626)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 10 Inch Length

from

$22.79
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Molded 90 Degree Heater Hose (Part No.28466)

Molded 90 Degree Heater Hose

from

$19.29
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.

Product Features:
  • Resists electrochemical degradation and water permeation
  • Use with heater hose connectors and bulk heater hose to create custom assemblies
  • Compatible for coolant, air and water applications
  • EPDM tube and cover, synthetic fiber reinforcement
  • SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
  • Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
  • Caution: Do not use for fuel or oil transfer applications
See More

Most Sold 1994 Nissan Sentra Serpentine and V Belts

Explore our best-selling Nissan parts for the 1994 Sentra among 31 OEM and aftermarket options starting from $13.64.

Dayco – Poly Rib Belt Serpentine Belt; 33.27 Long, 4 Rib Count (Part No.5040333)

Poly Rib Belt Serpentine Belt; 33.27 Long, 4 Rib Count

from

$35.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Dayco – Poly Rib Belt Serpentine Belt; 31.5 Long, 4 Rib Count (Part No.5040315)

Poly Rib Belt Serpentine Belt; 31.5 Long, 4 Rib Count

from

$33.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Driveworks – Poly Rib Belt Serpentine Belt; 40.75 Long, 6 Rib Count (Part No.408K6)

Poly Rib Belt Serpentine Belt; 40.75 Long, 6 Rib Count

from

$21.99
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
See More

Dayco – Poly Rib Belt Serpentine Belt; 35.83 Long, 4 Rib Count (Part No.5040358)

Poly Rib Belt Serpentine Belt; 35.83 Long, 4 Rib Count

from

$24.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Driveworks – Poly Rib Belt Serpentine Belt; 33.27 Long, 4 Rib Count (Part No.333K4)

Poly Rib Belt Serpentine Belt; 33.27 Long, 4 Rib Count

from

$30.49
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
See More

Dayco – Poly Rib Belt Serpentine Belt; 40.75 Long, 6 Rib Count (Part No.5060408)

Poly Rib Belt Serpentine Belt; 40.75 Long, 6 Rib Count

from

$25.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Dayco – Poly Rib Belt Serpentine Belt; 32.09 Long, 4 Rib Count (Part No.5040320)

Poly Rib Belt Serpentine Belt; 32.09 Long, 4 Rib Count

from

$33.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Driveworks – Poly Rib Belt Serpentine Belt; 31.5 Long, 4 Rib Count (Part No.315K4)

Poly Rib Belt Serpentine Belt; 31.5 Long, 4 Rib Count

from

$33.99
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
See More

Driveworks – Poly Rib Belt Serpentine Belt; 32.09 Long, 4 Rib Count (Part No.320K4)

Poly Rib Belt Serpentine Belt; 32.09 Long, 4 Rib Count

from

$21.79
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
See More

Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100026443MBL)

Multi-Rib (Serpentine) Belt

from

$25.90
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
See More

Driveworks – Poly Rib Belt Serpentine Belt; 35.83 Long, 4 Rib Count (Part No.358K4)

Poly Rib Belt Serpentine Belt; 35.83 Long, 4 Rib Count

from

$15.79
This Driveworks v-belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks v-belt delivers long-lasting dependable belt life.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
  • Meets OEM requirements
See More

Dayco – Poly Rib Belt Serpentine Belt; 32.5 Long, 4 Rib Count (Part No.5040325)

Poly Rib Belt Serpentine Belt; 32.5 Long, 4 Rib Count

from

$25.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
  • Made in the USA
See More

ContiTech – Multi Rib (Serpentine) Belt (Part No.W1000108435CON)

Multi Rib (Serpentine) Belt

from

$27.20
ContiTech Serpentine Belts come in a wide range of sizes and are designed to be oil-resistant and temperature-stable from -22F to 176F (-30C to 80C). ContiTech Serpentine Belts deliver 98% power efficiency. While a lower profile design easily handles higher engine revs, reducing noise and providing cooler running temperatures. High performance construction features include polychloroprene rubber cover and body, polyester fiber tensile members, and a ribbed belt design. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Temperature-stable from -22F to 176F (30C to 80C).
  • Delivers over 98% power efficiency.
  • High performance construction.
  • Polychloroprene rubber cover and body.
  • Polyester fiber tensile members and a ribbed belt design.
See More

Dayco – Poly Rib Belt Serpentine Belt; 33.07 Long, 4 Rib Count (Part No.5040330)

Poly Rib Belt Serpentine Belt; 33.07 Long, 4 Rib Count

from

$23.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:
  • Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
  • Engineered to help address noise issues caused by the belt drive 
  • Capable of handling more extreme temperatures and workloads
See More

Gates – Micro-V« Serpentine Drive Belt (Part No.K040360)

Micro-V« Serpentine Drive Belt

from

$28.99
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.

Product Features:
  • Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
  • EPDM rubber constructions resist cracking on the rib surface
  • Meets or exceeds all specifications from the Original Equipment Manufacturer
  • Tensioner Replacement is Recommended (if equipped)
  • Unique form grinding of each individual belt assures precise dimensional control.
  • Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
See More

Dayco – Dayco, Drive Belt (Part No.W10001221199DAY)

Dayco, Drive Belt

from

$19.81
Built for passenger cars and light-duty trucks, Dayco’s extensive line of Poly Rib serpentine belts are engineered for high mileage, demanding drives found in today’s vehicles. As the manufacturer of the first original equipment multi-ribbed serpentine belt, Dayco’s commitment to automotive product excellence and innovation is unwavering. The Dayco Poly Rib W Profile serpentine belt is the most innovative advancement in serpentine belt design in more than 30 years. Developed through extensive laboratory and actual road mileage testing, this unique rib profile EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and help eliminate noisy belt conditions. Constructed with aramid-reinforced EPDM compounds, the Dayco W Poly Rib serpentine belt delivers more than just OE-required quality. It delivers the solution to troublesome drive problems.

Product Features:
  • Constructed with aramid-reinforced EPDM compounds
  • Engineered to conform to high mileage, worn or misaligned drives
  • Helps eliminate noisy belt conditions Related Documents: (PDF 63.78 KB)
See More

Gates – Micro-V« Serpentine Drive Belt (Part No.K060408)

Micro-V« Serpentine Drive Belt

from

$27.49
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.

Product Features:
  • Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
  • EPDM rubber constructions resist cracking on the rib surface
  • Meets or exceeds all specifications from the Original Equipment Manufacturer
  • Tensioner Replacement is Recommended (if equipped)
  • Unique form grinding of each individual belt assures precise dimensional control.
  • Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
See More

Gates – Micro-V« Serpentine Drive Belt (Part No.K040320)

Micro-V« Serpentine Drive Belt

from

$27.49
Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.

Product Features:
  • Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
  • EPDM rubber constructions resist cracking on the rib surface
  • Meets or exceeds all specifications from the Original Equipment Manufacturer
  • Tensioner Replacement is Recommended (if equipped)
  • Unique form grinding of each individual belt assures precise dimensional control.
  • Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.
See More

Carquest Standard – Serpentine Belt: 31.5" Long, 4 Rib Count (Part No.315K4)

Serpentine Belt: 31.5" Long, 4 Rib Count

from

$22.99
Carquest Standard serpentine belts are constructed from quality materials to ensure durability and a long lifespan. We design and manufacture each Carquest Standard belt to enhance belt-to-pulley contact, maximizing load-carrying capacity and extending belt life. Our serpentine belts are built with EPDM rubber and treated polyester cord to improve durability and belt life. Carquest Standard belts are the right choice when looking for OE fit, form, and function at a great price.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
  • Meets OE fit, form, and function
See More

Carquest Standard – Serpentine Belt: 33.3" Long, 4 Rib Count (Part No.333K4)

Serpentine Belt: 33.3" Long, 4 Rib Count

from

$22.99
Carquest Standard serpentine belts are constructed from quality materials to ensure durability and a long lifespan. We design and manufacture each Carquest Standard belt to enhance belt-to-pulley contact, maximizing load-carrying capacity and extending belt life. Our serpentine belts are built with EPDM rubber and treated polyester cord to improve durability and belt life. Carquest Standard belts are the right choice when looking for OE fit, form, and function at a great price.

Product Features:
  • Constructed with heat and ozone resistant EPDM rubber
  • Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
  • Made with treated polyester cord to reduce belt stretch
  • Meets OE fit, form, and function
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W100026443BAN)

Multi Rib (Serpentine) Belt

from

$21.67
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

ContiTech – Multi Rib (Serpentine) Belt (Part No.W100027958CON)

Multi Rib (Serpentine) Belt

from

$17.19
ContiTech Serpentine Belts come in a wide range of sizes and are designed to be oil-resistant and temperature-stable from -22F to 176F (-30C to 80C). ContiTech Serpentine Belts deliver 98% power efficiency. While a lower profile design easily handles higher engine revs, reducing noise and providing cooler running temperatures. High performance construction features include polychloroprene rubber cover and body, polyester fiber tensile members, and a ribbed belt design. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Temperature-stable from -22F to 176F (30C to 80C).
  • Delivers over 98% power efficiency.
  • High performance construction.
  • Polychloroprene rubber cover and body.
  • Polyester fiber tensile members and a ribbed belt design.
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W100027637BAN)

Multi Rib (Serpentine) Belt

from

$16.71
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W100036482BAN)

Multi Rib (Serpentine) Belt

from

$15.40
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100027637MBL)

Multi-Rib (Serpentine) Belt

from

$15.27
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W100027638BAN)

Multi Rib (Serpentine) Belt

from

$15.10
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100026956MBL)

Multi-Rib (Serpentine) Belt

from

$14.51
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
See More

Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100027958MBL)

Multi-Rib (Serpentine) Belt

from

$14.44
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W100027958BAN)

Multi Rib (Serpentine) Belt

from

$14.40
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100026447MBL)

Multi-Rib (Serpentine) Belt

from

$14.13
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
See More

Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100027189MBL)

Multi-Rib (Serpentine) Belt

from

$13.64
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
See More

Top-Rated Belts and Hoses Brands For Your 1994 Nissan Sentra

Shop for the best-rated brands offering Belts and Hoses and other products for your 1994 Nissan Sentras. Below you’ll find some of our best rated Belts and Hoses from Dayco and Driveworks, and more. Belts and Hoses from these brands that fit a 1994 Sentra start at just $10.68 and are rated as high as 5 stars. OEM and aftermarket Belts and Hoses don’t get more top quality, durable, and affordable than from the brands below.

Popular Dayco 1994 Nissan Sentra Belts and Hoses

When it comes to maintaining or upgrading your 1994 Nissan Sentra, using quality Belts and Hoses is essential to ensure durability and a perfect fit. Dayco ticks all of those boxes. We offer a wide selection of Dayco Belts and Hoses, specifically designed for the 1994 Nissan Sentra. With over 21 Dayco brand Belts and Hoses in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $10.68, with an average price of just $21.99. Plus, with over 91 customer reviews and an average rating of 5 stars, you can trust that our Dayco Belts and Hoses will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

Popular Driveworks 1994 Nissan Sentra Belts and Hoses

Driveworks auto parts is one of the highest quality Belts and Hose brands in the market. Any 1994 Nissan Sentra owner should feel confident when installing genuine Driveworks parts in their vehicle. To ensure the best fit and performance for your 1994 Sentra, Advance Auto Parts carries a full inventory of 5 Driveworks Belts and Hoses. Plus you will be keeping your Nissan in peak condition while saving money because prices on these Driveworks Belts and Hoses range from $15.79 to $33.99, plus, with more than 44 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Belts and Hoses below will deliver on both quality and value.

Poly Rib Belt Serpentine Belt; 35.83 Long, 4 Rib Count
from
$15.79
This product is not rated

Poly Rib Belt Serpentine Belt; 35.83 Long, 4 Rib Count

“”

FAQs for 1994 Nissan Sentra Belts and Hoses

Which Belts and Hoses are best-sellers for 1994 Nissan Sentras?

Out of 58 Belts and Hoses that fit 1994 Nissan Sentras, the following parts are the top sellers:

What’s the price range for 1994 Nissan Sentra Belts and Hoses?

Belts and Hose prices for the 1994 Nissan Sentra start at $1.79 and go up to $87.99 for the most premium parts.

What’s the average price of a Belts and Hose for a 1994 Nissan Sentra?

The average price for Belts and Hoses for the 1994 Nissan Sentra is $24.25. Keep in mind the variety of part types within our Belts and Hose category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Belts and Hoses for other Nissan Sentra model years?

Yes, we currently carry Belts and Hoses for 42 model years of Nissan Sentras between 1982 and 2024. Belts and Hoses are bought most frequently for the following model years: 2019, 2018, 2017, 2016, 2015, 2014, 2013, 2012, and 2011.

What are the cheapest Belts and Hoses for my 1994 Nissan Sentra?

The cheapest 1994 Nissan Sentra Belts and Hoses we carry in stock are:

What are the top-rated Belts and Hoses that fit the 1994 Nissan Sentra?

Out of 327 reviews by customers, our 1994 Nissan Sentra Belts and Hoses have an average customer rating of . These are some of the highest-rated Belts and Hose types for the 1994 Nissan Sentra and their top-rated products:

What types of Belts and Hoses do you sell for my 1994 Nissan Sentra?

As of 2/5/25, these are some of the most in-demand types of Belts and Hoses for a 1994 Nissan Sentra:

Can I get help with 1994 Nissan Sentra Belts and Hose orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Nissan Belts and Hoses and more.

What is your return policy for Nissan Sentra Belts and Hoses?

Advance Auto Parts keeps returns simple. For new Nissan Sentra Belts and Hoses and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.