1994 Mazda MX-6 Belts and Hoses

MacKay utilizes leading edge rubber technology and compounds, supported by in-house processes from rubber mixing to final product. This ensures hoses are made to the strict specifications required for the advanced motor vehicles of the 21st century. In vehicles of today, a hose has to be designed to withstand the stresses of modern, more compact but powerful engines that run hotter and at a higher pressure. Other factors include smaller engine compartments with poor heat dissipation, aggressive coolant additives, and stray (electrochemical) current that may be conducting through the cooling system. In short, the smaller but more powerful engines of today work a lot harder than the larger engines that were standard before. More heat is generated, higher burst pressures are required in cooling system components, and hoses have to be made tougher to withstand these demands. MacKay’s research and development chemists have developed new rubber formulations and manufacturing processes that ensure MacKay hoses meet the greater wear and heat demands created by modern engines. Rubber compounds used in automotive hoses today are predominantly synthetic rubber formulation. All MacKay coolant hoses are made from EPDM compounds that are highly resistant to ozone attack. Hoses made from some other rubber compounds may be subject to ozone deterioration.

Product Features:

• Excellent resistance to high temperatures
• Resists chemical attack (oils, fuels etc.)
• Excellent Ozone resistance
• Good resistance to abrasion
• High resistance to vibration

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Dayco, Heater Hose, 90 Trim-to-Fit

This pulley is supplied by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This heavy duty steel pulley conforms to original equipment material and tolerances, specifications and meets performance and durability requirements. Fits Ford/Mazda applications Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._

Product Features:

• Manufactured by the original equipment part supplier to ensure proper form, fit and performance
• Heavy Duty Steel Pulley
• Precision steel stamping with close tolerance ball bearing pocket.
• Electro-deposited coating (e-coat) for superior corrosion resistance.
• Running surface designed and engineered for proper belt tracking.

This Litens pulley is supplied by one of the largest automotive pulley suppliers in the world and meets all form, fit, and performance characteristics of the original equipment part . Like the Original Equipment (O.E.) pulley, the Litens replacement part is constructed of heavy duty steel for long life and trouble free performance. This pulley, is manufactured in Japan for both O.E. and aftermarket Mazda/Ford applications. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.

Product Features:

• Improved sealing surface for greater leak resistance
• High flexibility for easy installation
• Maximum vehicle coverage with minimum inventory
• Resistant to heat, oil and ozone
• Rated for SAE 20R5 Class D-2 performance
• Temperature Range: up to +257 Deg. F (+125 Deg. C)
• Note: Gates recommends replacing clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:

• Designed to meet OE specifications
• Not suitable for oil or heat transfer
• Meets SAE J20R4, Class D-2 requirements for improved service hoses
• This hose is designed to prevent splitting, ballooning, and elongation

The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.

Product Features:

• Constructed with heat and ozone resistant EPDM rubber
• Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
• Made with treated polyester cord to reduce belt stretch

Import or domestic, car or truck, every vehicle can depend on the superior quality of Gates precision fit Micro-V belts. With advanced technology that matches the OE size, construction and materials, Gates Micro-V ensures optimal vehicle performance.

Product Features:

• Special belt construction eliminates belt noise, reduces tension loss and solves problem drive applications
• EPDM rubber constructions resist cracking on the rib surface
• Meets or exceeds all specifications from the Original Equipment Manufacturer
• Tensioner Replacement is Recommended (if equipped)
• Unique form grinding of each individual belt assures precise dimensional control.
• Meets or exceeds SAE J1459, SAE J2432, and SAE J1596 specifications.

Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:

• Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
• Engineered to help address noise issues caused by the belt drive 
• Capable of handling more extreme temperatures and workloads

Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:

• OE-Equivalent.
• Direct fit for easy installation.
• Resistant against wear, oil and heat.
• Strong tensile cords limit stretching.
• Supports higher horsepower loads.
• Made from high strength synthetic rubber.

Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:

• OE-Equivalent.
• Direct fit for easy installation.
• Resistant against wear, oil and heat.
• Strong tensile cords limit stretching.
• Supports higher horsepower loads.
• Made from high strength synthetic rubber.

Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:

• OE-Equivalent.
• Direct fit for easy installation.
• Resistant against wear, oil and heat.
• Strong tensile cords limit stretching.
• Supports higher horsepower loads.
• Made from high strength synthetic rubber.

Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.

Product Features:

• Resists electrochemical degradation and water permeation
• Use with heater hose connectors and bulk heater hose to create custom assemblies
• Compatible for coolant, air and water applications
• EPDM tube and cover, synthetic fiber reinforcement
• SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
• Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
• Caution: Do not use for fuel or oil transfer applications

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:

• Has all the quality features of Gates molded coolant hose and similar to OEM specifications
• Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
• EPDM tube, synthetic fiber knit reinforcement, EPDM cover
• Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
• Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:

• Engine oil cooler hose
• Size: 1/2″ x 12′
• Designed for engine oil applications
• 12′ hose length accommodates most applications

Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:

• Metal line kit
• For use in engine oil cooler applications
• Routes oil lines past exhaust manifolds
• Provides protection where standard hoses can fail

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Radiator Hose

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Product Features:

• Improved sealing surface for greater leak resistance
• High flexibility for easy installation
• Maximum vehicle coverage with minimum inventory
• Resistant to heat, oil and ozone
• Rated for SAE 20R5 Class D-2 performance
• Temperature Range: up to +257 Deg. F (+125 Deg. C)
• Note: Gates recommends replacing clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements