Name: Super Victor 4500 for Raised Port 23 Degree Intake Manifold Small-Block Chevy
Brand: Edelbrock
SKU: 2971
Price: 494.99 USD

from

$494.99

Product Features:

3500-8000 RPM Range
Single Plane Type-4500 Style Flange
6.77 in. Front Height, 6.77 in. Center Height, 6.77 in. Rear Height
Satin Finish
For Raised Port 23 Degree Heads

from

$258.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$42.49

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

Advance the cam for increased torque and horsepower
Tune your powerband for more end torque or increase top end horsepower
Includes (4) offset bushings and (1) 0 degree bushing
Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
Increase Top-End Horsepower

from

$95.99

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

Valve Spring Retainers for Use OE Cast Iron Heads
Superior Quality Heat-Treated Steel
Machined for Strength with Black Oxide Finish
Finish Ensures Rust and Corrosion Protection

from

$709.99

Holeshot 2400 for GM 1998 to 2002 4L60E Camaro and Firebird with an LS1 engine Application: GM 1998 to 2002 4L60E Camaro and Firebird with LS1 A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benef

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$32.99

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

Chrome Plated
Grade 5
AN washers with no exposed shoulder for a professional appearance

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$42.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use

from

$36.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.
Not intended for use in emission controlled vehicles.

from

$94.99

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$58.99

Product Features:

4.125 in. Cylinder Bore Diameter
0.039 in. Thickness
8.7cc Volume
Charcoal Color
Two Piece Configuration

from

$32.99

Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.

Product Features:

Manufactured from .020″ steel shim stock.
Thinner than composition head gaskets – increases engine compression.
Stress formed embossments seal extreme cylinder pressures.
For high performance street, drag race and oval track use.

from

$187.99

Product Features:

Case-Hardened Tubing
Surface Hardening
Welded Ends
0.3125 in. Diameter
Use with or without Hardened Steel Guideplates

from

$189.99

Product Features:

Case-Hardened Tubing
Welded Ends
5/16 in. Diameter
Use with or without Hardened Steel Guideplates

from

$20.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Steel core gasket construction
Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
Not intended for use in emission controlled vehicles.

from

$41.99

Product Features:

Replacement Gasket Set For PN[4242]

from

$334.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$306.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$65.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$147.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

Complete Kit: Includes Retainers And Locks
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Includes Superior Quality Steel Retainers
Includes 7 deg. Heat-Treated Valve Stem Locks
Retainers and Locks Black Oxide Coated
Dyno Tested And Street Proven
Great Match to Edelbrock Camshaft Kit

from

$23.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$38.49

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair, these gaskets are .187 inch thick. They fit both 1987-2002 Gen I Chevrolet Small Blocks as well as 1992-1997 Gen II LT-Based Small Blocks.

Product Features:

Manufactured from high-density cork /rubber blend gasket material
A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
For OE replacement, high performance street, drag race and oval track
.187″ thick
Handles Ex Flange Pressure
Forms Leak Proof Seal
Black Latex Coating

from

$17.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$75.99

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

Chrome plated
Grade 8
12-point head
AN washers with no exposed shoulder for a professional appearance

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$1028.99

Product Features:

Designed for 1987-95 Throttle Body Injection or Tuned Port Injection 5.7L Small-Block Chevy engines originally equipped with center bolt valve covers
Flat Tappet Camshaft Type
60cc chambers with 165cc intake ports
Size of intake valve is 2.02 in. and exhaust valve is 1.60 in.
Sold as one complete head

from

$605.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Hand-Blended Intake and Exhaust Bowls
CNC-Matched Intake/Exhaust Ports in Std Location
Thicker Deck Surfaces than Other Brands
Hardened Tip Stainless Swirl-Polished Valves
Heli-Coils Rocker Studs And Exhaust Bolt Holes

from

$927.99

The Edelbrock #609019 Performer cylinder head is designed for 302, 327, 350 and 400 cid small-block Chevy engines up to 1986. This cylinder head includes your choice of 64cc (In order to retain stock compression ratio on 1970 and earlier small-blocks) or

1994 GMC G1500 Performance Engines

More 1994 GMC G1500 Performance Engines

Essential 1994 GMC G1500 Performance Engines

Edelbrock – Super Victor 4500 for Raised Port 23 Degree Intake Manifold Small-Block Chevy (Part No.2971)

Competition Cams – CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA (Part No.12-250-3)

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

B & M – Holeshot 2400 (Part No.70441)

Mr. Gasket – Bolt Water Pump (Part No.4998)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1819)

Mr. Gasket – Intake Gasket (Part No.143)

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Edelbrock – Cylinder Head Gasket Set for Chevrolet (Part No.7310)

Mr. Gasket – Head Gasket (Part No.1130G)

Edelbrock – Pushrod Set for S/B Chevy (Part No.9629)

Edelbrock – Pushrod Set for S/B Chevy (Part No.9630)

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Edelbrock – Replacement Timing Cover Gasket #4243 For SB Chevy, Fits 2-Piece Part #4242 (Part No.4243)

Edelbrock – Performer-Plus Camshaft Kit for 1957-86 Small-Block Chevrolet (Part No.2103)

Edelbrock – Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet (Part No.3702)

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5894)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5867)

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

Mr. Gasket – Intake Bolt Kit (Part No.5003)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Edelbrock – Performer Small-Block Chevy Cylinder Head Hydraulic Flat Tappet Cam (Part No.60859)

Edelbrock – Engine Cylinder Head (Part No.60849)

Edelbrock – Performer Small-Block Chevy Cylinder Head 64cc Flat Tappet Polished (Part No.609019)

Popular 1994 GMC G1500 Performance Engines Categories

1994 GMC G1500 Performance Engines

Performance Engines Brands To Make Your 1994 GMC G1500 Last

Popular FEL-PRO Performance Performance Engines

Top 1994 GMC G1500 Performance Engines from Mr. Gasket

FAQs for 1994 GMC G1500 Performance Engines

What are the most purchased Performance Engines for the 1994 GMC G1500?

What are the top-rated 1994 GMC G1500 Performance Engines?

More Popular Parts for All Makes