1994 Dodge Dakota Performance and Racing Products
More 1994 Dodge Dakota Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1994 Dodge Dakota, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1994 Dodge Dakota Performance and Racing Products
Accel – High-Performance Ignition Coil – Direct OE Fit (Part No.140021)
from
$72.39
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Standard Motor Products SMP Uf-198
- MSD 8228
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
MSD Ignition – Tach Adapter (Part No.8910)
from
$91.99
In some instances when you install an MSD ignition, the factory ECU may not be able to distinguish when the coil fires. This is the signal that is also responsible for firing the injectors (or the tachometer), which may cause a no-run situation. The dual channel ignition adapter simulates the original coil trigger signal thus allowing the ECU to properly trigger both the tach and fuel injection with the MSD DIS ignition installed. In most cases, the adapter plugs directly into the MSD’s harness. For vehicles using an MSD DIS-2 ignition, only one PN 8912 is required. For DIS-4 applications, two PN 8912’s are required.
Product Features:
See More
Product Features:
- Designed for non-current limiting ignitions
- Size Non-Current Limiting Ignitions
- Easy mounting and installation
- Simulates the coil signal
Flowtech – Header Gasket Set (Part No.99361FLT)
from
$18.59
Header Gasket Set
Mallory – Distributor Wiring Harness (Part No.29349)
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1008)
from
$41.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
- Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
- Raises combustion sealing force to roughly three times that of standard head gaskets.
- Steel wire rings for the greatest combustion seal strength.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Super Intake Manifold Bolts (Part No.6080)
from
$27.49
These grade 5 hex head bolts are black coated plated for protection and appearance. Hardened flat washers provide uniform torque and prevent galling on aluminum manifolds.
Product Features:
See More
Product Features:
- Assures Accurate Torque App
- Prevents Galling Manifold
- Grade 5 Material
- Black Oxide Coasted
Edelbrock – Valve Cover Gasket Set for Chrysler (Part No.7593)
from
$29.99
Product Features:
See More
- 5/16 in. Thick
- Conforms to warped flanges, giving them better sealing capabilities
- Graphite-impregnated facing and steel expanded metal core
- Does not deteriorate or crack under excessive heat and pressure
- Sold as a pair
Mallory – Unilite Electronic Ignition Distributor Series 37 (Part No.3757901)
from
$538.99
The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.
Product Features:
See More
Product Features:
- Improved Combustion And Economy
- Increased Spark Plug Life
- Improved Cold Weather Starting
- Maintenance Free Operation
- Accurate Spark Timing
- Self-Lubricating Bushings
- Years Of Trouble-Free Service
K&N – Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (Part No.E-1080)
from
$89.99
K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.
Product Features:
See More
Product Features:
- ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
- RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
- 4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
- CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
- ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
- EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
- ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
- MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Powertrax – Lock Right Locker (Part No.1230-LR)
from
$450.99
The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles. Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction. Powertrax® = Extreme Traction Systems!
See More
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2004)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
Competition Cams – High Energy 218/218 Hydraulic Flat Cam and Lifter Kit for Chrysler 273-360 (Part No.CL20-212-2)
from
$1093.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering
Product Features:
See More
Product Features:
- Good blend of efficiency and performance.
- Perfect choice for performance street rebuilds.
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
Dynomax – Ultra Flo Muffler: Universal Fit, Stainless Steel, 16" L, 3" In, 3" Out, Round (Part No.17296)
from
$119.99
DynoMax Ultra Flo SS Polished performance mufflers are constructed of stainless steel for lifelong durability and completely polished for show-quality shine. The unrestricted, straight-through design is dyno proven to flow up to 2,000 SCFM and support up to 1,900 horsepower. Each muffler uses our exclusive Continuous Roving Fiberglass (CRF) Technology to absorb unwanted interior resonance while maintaining a deep performance tone.
Product Features:
See More
Product Features:
- Stainless steel construction for lifelong protection
- Polished finish for a show quality shine
- Dyno proven to flow up to 2,000 SCFM and support up to 1,900 horsepower
- Straight through design ensures unrestricted exhaust flow and reduces back pressure
- CRF Technology absorbs unwanted interior resonance while maintaining a deep performance tone
Accel – Adp.Harness 98/Newer Mopar (Part No.140021AH)
from
$35.49
Allows you to directly plug into the ACCEL PN 140021 Super coil when being used on a 1998 to 2002 Dodge truck, or Jeep equipped with a distributor and the newer light grey Yazaki wire harness coil connector. No cutting or splicing is required.
Product Features:
See More
Product Features:
- Nice Clean Connection
- Easy Installation
Richmond Gear – RngPnn (Part No.CR825355)
from
$185.99
RngPnn
Accel – Universal Fit Graphite Suppression; Spark Plug Wire Set (Part No.8026)
from
$128.99
These ACCEL carbon and graphite core wire sets virtually eliminate RFI noise, while providing maximum conductivity for ultimate performance in any race or street application. Double silicon insulation eliminates leakage and misfire.
Product Features:
See More
Product Features:
- Heavy Duty 8.8mm Oversized Silicone Jacket
- 500 Ohms/ft. Of Resistance
- 550 Degree Double Silicone Construction
- Fiberglass Braid
- Carbon/Graphite Core
- Magnetic Suppression
- Fiberglass/Kevlar Core
- 500 Ohms Resistance
Energy Suspension – SwyBarBshKt (Part No.5.5167G)
from
$25.99
SwyBarBshKt
Dynomax – 45293 Exhaust Tail Pipe (Part No.45293)
from
$75.99
Made from quality materials for durability, DynoMax® pipe is manufactured with precision benders and fixture checked to ensure a precise fit for quick and easy installation.
Product Features:
See More
Product Features:
- IMPROVED FLOW CAPACITY — Mandrel bends (where applicable) improve flow capacity over traditional bends while increased pipe diameter from OE sizes increases flow and power
- DESIGNED TO PERFORM — Fixture checked to ensure a precise fit for quick and easy installation
- AVAILABLE IN DIFFERENT SIZES — Offered in a variety of styles and sizes for a quality vehicle repair
- PREMIUM MATERIALS – Made from aluminized steel for durability and long life
- BETTER TOGETHER — Use premium DynoMax® accessories when installing DynoMax mufflers and exhaust systems for a complete performance exhaust system upgrade
Dynomax – 55255 Exhaust Intermediate Pipe (Part No.55255)
from
$66.99
Made from quality materials for durability, DynoMax® pipe is manufactured with precision benders and fixture checked to ensure a precise fit for quick and easy installation.
Product Features:
See More
Product Features:
- IMPROVED FLOW CAPACITY — Mandrel bends (where applicable) improve flow capacity over traditional bends while increased pipe diameter from OE sizes increases flow and power
- DESIGNED TO PERFORM — Fixture checked to ensure a precise fit for quick and easy installation
- AVAILABLE IN DIFFERENT SIZES — Offered in a variety of styles and sizes for a quality vehicle repair
- PREMIUM MATERIALS – Made from aluminized steel for durability and long life
- BETTER TOGETHER — Use premium DynoMax® accessories when installing DynoMax mufflers and exhaust systems for a complete performance exhaust system upgrade
Energy Suspension – Sway Bar Bushing Set (Part No.5.5118R)
from
$42.99
Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.
Product Features:
See More
Product Features:
- Allows Sway Bar System to Work At 100% Efficiency
- Zerk Type Fittings
- Allows for Periodic Greasing
- Lasts Much Longer Than OEM Rubber Bushings
- Handling Characteristics Improve Dramatically
Accel – Tst Dodge99-01 5.2L 99-02 5.9L (Part No.TST24)
from
$218.99
Everything you need to Super Tune Up your truck, van, or Jeep engine! The kits includes a high performance cap and rotor. A set of 8mm Extreme 9000 Spiral Core wires. This kit also includes the ACCEL classic copper core spark plugs to fire your engine up.
Product Features:
See More
Product Features:
- Complete Super Tune Kit
- 8mm Spiral Core Wires
- Accel Classic Core Plugs
- High Performance Cap And Rotor
- Reduced Emissions
Accel – Ignition/Electrical (Part No.8321)
Energy Suspension – Body Cab Mount Set (Part No.5.4106R)
from
$99.99
Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.
Product Features:
See More
Product Features:
- Assures Longer Lasting Cab to Bed Alignment
- Replace to Restore Ride Height
- Gain Durability
- Stronger Than Original Rubber Mounts
Energy Suspension – Body Cab Mount Set (Part No.5.4106G)
from
$103.99
Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.
Product Features:
See More
Product Features:
- Assures Longer Lasting Cab to Bed Alignment
- Replace to Restore Ride Height
- Gain Durability
- Stronger Than Original Rubber Mounts
Energy Suspension – CntrlArmBshngKt (Part No.5.3139R)
from
$96.99
CntrlArmBshngKt
Energy Suspension – Control Arm Bushing Set (Part No.5.3115G)
from
$83.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Energy Suspension – CntrlArmBshngKt (Part No.5.3139G)
from
$98.99
CntrlArmBshngKt
Popular 1994 Dodge Dakota Performance and Racing Products Categories
1994 Dodge Dakota Performance and Racing Products
You count on your 1994 Dodge Dakota to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 34 Performance and Racing Products ranging in price from $17.99 to $1,093.99, you’re sure to find everything you need for your 1994 Dodge Dakota.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 14 different brands like K&N, Accel, and Energy Suspension. 1994 Dodge Dakota Performance and Racing Products start as low as $17.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 460 extensive product reviews on 1994 Dodge Dakota Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Intake Manifold Bolts with 4.6 stars and 50 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Moderate Sound with 4.7 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1994 Dodge Dakota below to get started!
Top-Rated Performance and Racing Products Brands For Your 1994 Dodge Dakota
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1994 Dodge Dakota running right for years to come. In our inventory you’ll find brands like K&N, Accel, Energy Suspension, and even more.
Popular Mallory Performance and Racing Products
You’ll find popular Mallory brand products across Performance Ignition Products. All are waiting to get your 1994 Dodge Dakota back on the road. Some of the top-rated Mallory products in these categories are:
Top-Rated K&N Performance and Racing Products
If K&N are what you’re looking for, our inventory holds plenty. We stock K&N brand Performance and Racing Products for your 1994 Dodge Dakota, and some of our most reviewed K&N parts include:
from
$17.99
(120)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
from
$102.99
(5)
Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration
Performance Air Filters
FAQs for 1994 Dodge Dakota Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1994 Dodge Dakota?
Out of 34 Performance and Racing Products for the 1994 Dodge Dakota, the most popular in our inventory are:
What are the top-rated 1994 Dodge Dakota Performance and Racing Products?
Top-rated Performance and Racing Products for your 1994 Dodge Dakota based on customer reviews/ratings are:
from
$154.99
(3)
50 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Moderate Sound
“Muffler was delivered on time and fit my 1994 Ford Ranger perfectly, and was easy to install (once I got the old one off). The whole muffler felt ‘sol”
