1993 Mazda Miata Ignition Boots

NGK Resistor Spark Plug Wire Sets utilize a construction method known as variable pitch wire winding to create resistance to radio frequency interference. The variable pitch winding (loose/tight/loose) provides suppression throughout a very wide range by scrambling and breaking up the electrical waves radiated by the firing of the spark plugs. A ferrite magnetic layer consisting of a mixture of rubber, plastic and powdered ferrite magnetic materials, offers uniform resistance and unsurpassed conductivity. NGK wires have a lower resistance than conventional carbon core wires (8k ohm/meter versus 16k ohm/meter). This comparison is important to remember when you consider that many manufacturers recommend wires be replaced when the resistance exceeds 20k ohm/meter. This does not leave much margin for wear when the wire may only meet original standards at the very early stages of its life.

Product Features:

• OE-Equivalent.
• OEM style connectors for easy Installation.
• Superior Firing and Fuel Savings
• Outstanding Durability and Performance
• Excellent Noise Suppression
• Numbered for easy cylinder identification.
• High quality EPDM and Silicone coverings.

NGK variable pitch resistor cables provide uniform resistance and ensure outstanding electrical conductivity in high-quality cables. Outer EPDM/silicone jacket and inner insulation contain high voltage currents for excellent dielectric strength. NGK varia

Product Features:

• PERFECT FIT FOR YOUR VEHICLE: Built to OEM tolerances with OE quality or better materials
• BUILT TO LAST: Outer Jacket built to withstand temperatures greater than 250 degrees C, inner insulation EPDM or silicone for best dielectric strength
• STAINLESS STEEL TERMINALS: Provide the highest possible retention to ensure positive connections through the life of the set
• PREMIUM ALLOY WINDING: Variable pitch winding over Ferrite magnetic alloy coating delivers ultra low resistance and excellent interference protection
• CYLINDER LEAD ID: Cylinder lead identification tags where possible make installation easier

CARQUEST Premium coil on plug boots are engineered to restore ignition boot reliability and performance. We have OE design providing an exact direct fit for your application and the performance and durability meet or exceed OE requirements. It offers excellent heat resistance as well as maximum protection against spark loss. With durable silicone compound for resistance to high heat or abrasion.

Product Features:

• Provides excellent heat resistance as well as maximum protection against spark loss.
• Durable silicone compound for resistance to high heat or abrasion
• Spring included with the coil boot
• Design for direct compatibility
• OE design provides an exact fit for your application
• Multipack provides one time replace all COP for better deal

NGK Coil on Plug Boots are built to stringent OEM tolerances, combining original equipment fit, design and outstanding durability. NGK Coil on Plug Boots are manufactured using only premium silicone and always include any required internal springs and ferrite resistors for superior performance and RFI noise suppression. Bridging the important link between ignition coil and spark plug, COP boots should always be replaced with NGK Coil on Plug Boots at the time as changing spark plugs to prevent ignition problems such as flashover.

Product Features:

• PREMIUM GRADE SILICONE: Designed to withstand harsh environments
• OEM MATCHED: Includes all required internal springs and ferrite resistors for superior performance and RFI noise suppression

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Bolt-on Performance
• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications
• Conductor core features DuPont Kevlar material for increased tensile strength
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately