from

$12.79

Product Features:

High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks
Long-life friction modifiers and premium base oils help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
Enhanced cleaning additives help reduce varnish formation and keep the transmission running properly longer
Engineered with a unique blend of viscosity modifiers and base oils to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$17.99

Product Features:

Pinion depth shims for Dana Spicer 60 and 70U

from

$629.99

9.25″ IFS & 9.5″ case standard Open, loeaded.

Product Features:

Standard open carrier case and spiders
Fits GM 9.25″ IFS and 9.5″

from

$153.99

Set-up bearing (one bearing). HM803146. No return.

Product Features:

Set up bearing
Fits HM803146 pinion bearing
Easily slips on and off pinion journal to allow for pinion depth adjustment

from

$7.99

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
0.225″ diameter
1.870″ long

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$141.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Dana Spicer 70U
Included are a pinion seal, complete shim kit, marking compound and brush.

from

$315.99

Yukon standard open spider gear kit for GM 10.5″ and 14T with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits GM 10.5″ 14 bolt truck open differential
Includes two side gears, four pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$276.99

Set-up carrier bearing kit (2 bearings, no races) for Dana 60 and 70. 387A. No return.

Product Features:

Set up bearing kit
Fits Dana Spicer 60
Easily slips on and off carrier journals to allow for easier carrier shim adjustment

from

$13.99

Crush Sleeve for Chrysler 9.25″ front, GM 8.6″ IRS, 9.25″ IFS & 9.5″. Approx 0.640″ long.

Product Features:

Crush sleeve for Chrysler 9.25″ front, GM 8.6″ IRS, 9.25″ IFS and 9.5″
0.640″ tall

from

$369.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits 1988 and down GM 10.5″ 14 bolt truck
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, pilot bearing, marking compound and brush.

from

$39.99

Replacement pinion seal for Dana 44HD, Dana 60 & Dana 70 .Yukon Mighty seal.

Product Features:

Pinion seal
Pinion seal
Fits Dana Spicer 44HD, 60, 70, 70U and 70HD

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$59.99

RngPnnInstlKt

from

$249.99

Product Features:

Spider gear kit
Fit Dana Spicer 70 and 80 open differential with 35 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$8.79

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

from

$596.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$232.99

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$13.99

Product Features:

Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

from

$7.99

Dana 70 & Dana 80 pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer for Dana Spicer 70 and 80

from

$47.99

Eaton positraction shim kit for 9.5″ GM.

Product Features:

Shim kit
Fits GM 9.5″ Eaton positraction

from

$5.99

DiffrlPinSupportBolt

from

$11.99

10.5″ GM 14 bolt truck ring gear bolt 4.56 & up. 9/16″ x 18. 2.522″ overall length.

Product Features:

Ring gear bolt for GM 10.5″ 14 bolt truck
4.56 and up ratio
1/2″ x 18 thread
2.522″ overall length

from

$22.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$26.99

Spartan spring & pin kit, fits larger designs.

Product Features:

Fits Dana Spicer 60
Replacement alignment pin and spring kit

from

$37.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft