from

$258.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$92.99

Conversion bearing for small bearing Ford 9″ axle in large bearing housing.

Product Features:

Axle bearing
Fits Ford 9″
Conversion bearing to install small bearing axle into large bearing housing
3.150″ O.D.
1.377″ I.D.

from

$30.99

Standard open and TracLoc cross pin block for 9″ Ford.

Product Features:

Cross pin block
Fits Ford 9″

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$187.99

8″ & 9″ Ford 4-Tab clutch kit with 9 pieces (late TracLoc).

Product Features:

Clutch kit
Fits Ford 8″ and 9″ Trac Loc positraction

from

$309.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$1183.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. This unit requires the use of a 3.250″ dropout. Use carrier bearing/race numbers LM104949/LM104911. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! This unit has been approved for competition in NASCAR National & Touring series. This is a race unit designed for extreme off road use or racing. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

Fits Ford 9″ with 31 spline axles
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA
Aggressive design for racing applications only

from

$5.99

Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt, 1.0″ long, Ford.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
1.0″ long

from

$20.29

This drive shaft bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this engine mount bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this drive shaft bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$26.49

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$203.99

Yukon yoke (short, for Daytona support) for Ford 9″ with 28 spline pinion and a 1330 U/joint size. 4″ length. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″
28 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.125″ cap diameter
U-bolt style

from

$42.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.250″ O.D.
1.400″ I.D.

from

$37.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$35.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$228.99

Product Features:

FRD 10BL 8.8 R/P 3.55 MG

from

$1993.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$9.99

7.5″ Ford cover gasket.

Product Features:

Cover gasket
Fits Ford 7.5″

from

$342.99

8.8″ Ford TracLoc clutch set (Carbon), both sides, 2003-2010 Cobra SVT.

Product Features:

Clutch kit
Fits Ford 8.8″ trac Loc positraction
Carbon fiber clutches

from

$209.99

Yukon yoke for Ford 8.8″ truck or passenger with a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″
30 spline
1330 u-joint size
3.625″ snap ring span
1.062″ cap diameter
Outside snap ring design
Strap style

from

$219.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M88010 race
All steel construction

from

$41.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$8.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$579.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect. This unit uses the factory side gears.

Product Features:

Fits Ford 8″ and 9″ with 28 or 31 spline axles
Made from 9310 steel for added strength
Works with stock side gears in standard carrier case

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$175.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9″ without aftermarket Daytona pinion support
Included are pinion bearings and races, pinion seal, pilot bearing , crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$201.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits 2009 and down Ford 8.8″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$226.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Ford 9″ with LM603011 carrier races
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.