from

$61.21

Differential Bearing

from

$445.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$218.99

Yukon standard open spider gear kit for GM 7.2″ S10 and S15 IFS. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits GM 7.2″ IFS
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$184.99

Yukon 1541H alloy rear axle for ’88-’97 GM 7.5″ S10 4WD with a length of 29 inches and 28 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

Fits 1988-1997 GM 7.5″ and 7.625″ in S10 with 4 wheel drive
28 spline
29″ long
5 lug

from

$27.99

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

from

$12.49

Valvoline High Performance Synthetic Gear Oil is the thermally stabile extreme pressure lubricant that offers outstanding protection for gearboxes and differentials in passenger cars, light trucks, and sport utility vehicles. Combined with high quality synthetic base oils, our formula’s superior additives help reliably safeguard against severe temperatures, shock loads, foaming, scuffing, scouring, corrosion and pitting in high load, high torque and high horsepower conditions. Can be used in conventional and limited slip hypoid differentials where GL-5 is specified as well as non-synchronized manual transmissions that require GL-4. Protect your gears with Valvoline, the #1 gear oil brand.

Product Features:

HIGH PERFORMANCE EXTREME-PRESSURE ADDITIVES HELP MINIMIZE WEAR in high pressure and high temperature conditions
EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION can easily handle both winter and summer conditions for dependable coverage and protection year-round
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
SUPERIOR ADDITIVES help reliably safeguard against severe temperatures, shock loads, foaming, scuffing, scouring, corrosion and pitting in high load, high torque and high horsepower conditions

from

$7.49

Product Features:

Brand may vary by location

from

$5.99

Differential Cover B

from

$28.99

7.2″ shifter seal.Yukon Mighty seal.

Product Features:

Shifter seal
Fits GM 7.2″ IFS

from

$57.99

Cross pin shaft for 7.5″, 7.625″, and 8″ GM.

Product Features:

Cross pin shaft for GM 7.5″, 7.625″ and 8.0″
Fits standard open differentials only

from

$234.99

Yukon cast yoke for GM 8.5″ with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.5″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$17.99

Standard open side gear thrust washer for 7.2″ GM.

Product Features:

Side gear thrust washer
Fits GM 7.2″ IFS

from

$25.99

Yukon 4340 Chrome-Moly replacement outer stub for D44 ’87-’94 Wrangler with a length of 8.31″ and 27 splines. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

27 spline
8.31″ long
Fits Dana Spicer 30 in 1987-1994 Wrangler
Outer stub
5-760X U-joint size
4340 Chromoly
For WARN hub conversion only

from

$14.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$32.99

Adjuster lock bolt for left hand case half of 7.2″ and 9.25″ GM IFS.

Product Features:

Side adjuster lock bolt
Fits GM 7.2″ IFS and 9.25″ IFS

from

$16.99

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$352.99

Yukon positraction internals for 8.5″ GM with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects. This kit is compatible with Yukon Dura Grip or Eaton positractions. It will not fit a factory Gov-Loc positraction.

Product Features:

Spider gear kit
Fits GM GM 8.5″ and 8.6″ Dura Grip positraction with 30 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and side gear thrust washers.

from

$26.49

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$7.99

Standard open pinion gear thrust washer for 7.2″ GM.

Product Features:

Pinion gear thrust washer
Fits GM 7.2″ IFS

from

$15.29

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

Manufactured from high quality elastomer compounds for durability and ride performance
Assembled with proper precompression for ultimate in performance and feel
High level bonding adhesive is used for durability
Elastomer compounds do not utilize any reground rubber fillers

from

$203.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1982-1999 GM 7.5″ and 7.625″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$10.99

Product Features:

Clutch guide
Fits GM 7.5″ and 7.625″ Dura Grip

from

$1.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$29.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$373.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
14 piece kit
Composite clutches

from

$9.99

Pinion nut for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.0″, 8.25″, 8.5″, 8.6″, 9.25″ IFS, 9.5″ & Oldsmobile Dropouts. 1 1/4″ socket, 7/8″ x 14 thread.

Product Features:

Pinion nut for GM 7.2″, 7.5″, 7.625″, 8.0″, 8.25″ IFS, 8.5″, 8.6″, 9.25″ IFS and 9.5″
7/8″ x 14 thread
1 1/4″ socket

from

$819.99

Hard use and poor lubrication can wear out a limited-slip differential. Restore original performance with this replacement differential carrier assembly that includes all-new spider gears, differential pins, clutches and carrier housing.

Product Features:

Direct replacement – this 30 spline limited-slip differential carrier fits in place of this vehicle’s original equipment carrier.
100% new – this differential carrier uses all-new components, including spider gears, diff pin, pre-load spring pack and clutch pack.
Ready to install – this differential carrier is shipped pre-assembled and ready to install
Ideal upgrade – can be used to upgrade from open differential to limited-slip in an existing differential

from

$344.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features: