1991 Mitsubishi Mighty Max Belts and Hoses
More 1991 Mitsubishi Mighty Max Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1991 Mitsubishi Mighty Max, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1991 Mitsubishi Mighty Max Belts and Hoses
Gates – Molded Heater Hose: EPDM, Direct Fit, 0.62" Inside Diameter (Part No.18774)
from
$30.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 24 Inch Length (Part No.80404)
from
$18.79
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 12 Inch Length (Part No.80401)
from
$18.29
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length (Part No.80402)
from
$23.49
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Dorman – Idler Pulley (Part No.G6020360519DOR)
from
$20.24
Dorman’s Belt Tensioner Pulley is engineered to maintain tension on the serpentine belt for the life of the belt–thereby keeping the alternator charging, the water pump running, and the power steering pump and A/C compressor operating properly. They feature a high-quality double-sealed bearing to resist damage from contaminants. Replacement prevents belt slip and eliminates squeak, squeal or groaning noise associated with a worn belt tensioner pulley.
Product Features:
See More
Product Features:
- Steel or plastic construction for long-lasting durability against heat, shock and corrosion
- Replacement stops squeak, squeal or groaning noise associated with a worn Belt Tensioner Pulley
- Direct replacement for a proper fit every time
- Vehicle try-on testing and rigorous materials testing to ensure high-quality performance
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10" Long, 1.25" Diameter (Part No.B70797)
from
$14.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.31" Diameter (Part No.B70796)
from
$11.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Poly Rib Belt Serpentine Belt; 53 Long, 5 Rib Count (Part No.5050530)
from
$23.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Febi – Accessory Belt Tension Pulley (Part No.G6011169724FEB)
from
$62.53
Accessory Belt Tension Pulley
Dayco – V-Belt Idler/Tensioner Pulley; Steel, 81mm Dia., 16.4mm Width, Grooves (Part No.89036)
from
$43.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 81 mm Diameter (Part No.900047A)
from
$31.49
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in the U.S.A. to the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Gates – Notched V-Belt: 38.12" Long, 1 Strand, Exact Fit (Part No.9375)
from
$37.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
ContiTech – Drive V-Belt (Part No.W100032560CON)
from
$11.32
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Polyester fiber tensile members and a ribbed belt design.
Dayco – Bottom Cog V-Belt; 29.25 Inch Long, Exact Fit Premium Quality (Part No.17293)
from
$9.29
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.
Product Features:
See More
Product Features:
- Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
- Provides greater durability and flexibility – 35% stronger than all previous versions
- Features specially treated cords for added strength, stability and reliability
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Sealed Power – Engine Balance Shaft Belt (Part No.222-92)
from
$9.69
Sealed Power parts provide innovative designs, use leading-edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.
Product Features:
See More
Product Features:
- Unsurpassed quality that you can trust
- Uses leading edge materials
- State-of-the-art manufacturing
- Exacting tolerances
- Meets or exceeds OEM specifications
Dayco – Premium Balance Shaft Belt, 20.48 Inch With 65 Round Tooth (Part No.95168)
from
$25.99
Manufactured with tough, wear-resistant fabric, high-tensile strength cord and a molded tooth surface, the Dayco timing belt provides consistent slip-proof power transfer and high resistance to oil and engine heat. The belt features a molded cog design which runs quieter and is more economical and a premium, high modulus glass fiber cord that delivers precise length stability to keep the engine running smoothly over the life of the belt.
Product Features:
See More
Product Features:
- Designed for specific OHC and DOHC applications that range from normal service to high performance, high temperature engines
- Offers noise reduction and minimum dimensional tolerances for precise valve timing
- Engineered with reduced elongation for maximum durability, high abrasion resistance and better performance
- Belt tooth profile specifically designed to fit sprockets precisely and maintain timing effectiveness
Dayco – Balance Shaft Belt (Part No.A5002169609DAY)
from
$15.72
Dayco is recognized by the automotive industry as a world leading manufacturer of timing belts. The Dayco timing belt, designed for OHC and DOHC type engines, features a molded cog design which runs quieter and is more economical. Our premium, high modulus glass fiber cord delivers precise length stability to keep the engine running smoothly over the life of the belt. The belt’s compounding and tooth configurations are designed for specific applications ranging from normal service to high performance, high temperature engines where HSN compound is used. The part number includes three final digits that conform to industry standard numbering. Dayco timing belts meet all original equipment manufacturer performance requirements.
Product Features:
See More
Product Features:
- Premium, high modulus glass fiber cord
- Molded cog design
- Meets all original equipment manufacturer performance requirements
Dayco – Flex Radiator Hoses; EPDM Rubber, 17.25 Inch Long, 1.25 Inch Inner Dia. (Part No.81051)
from
$21.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Flex Radiator Hoses; EPDM Rubber, 11 Inch Long, 1.25 Inch Inner Dia. (Part No.81031)
from
$27.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
ACDelco – Professional Molded Coolant Hose (Part No.G2000584211ACD)
from
$31.56
ACDelco Professional, premium aftermarket Molded Coolant Hoses are composed of specially blended materials to help resist electrochemical degradation (ECD), the leading cause of hose failure. They are specially designed, GM OE style factory-molded hoses to fit today’s smaller, tighter-fitting engine compartments. ACDelco Professional Molded Coolant Hoses are temperature rated from -40 degrees Fahrenheit to 275 degrees Fahrenheit (-40 degrees Celsius to 135 degrees Celsius) and are approved for Marine applications. Do not use for fuel or oil transfer applications. These premium aftermarket replacement molded coolant hoses are manufactured to meet or exceed your expectations for fit, form, and function.
Product Features:
See More
Product Features:
- Has a heat and ozone resistant cover to increase the life of the hose
- Comes with a protective sleeve to help duplicate GM OE designs for proper fit and function
- Made of re-engineered materials to resist vacuum collapse and also reduce the need for internal springs in many applications
- Installs without buckling, bending out of shape, or straining at the connection for easy installation
- Inside diameters ranges from 1?4 in to 1 in to fit different types of vehicles
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12.50" Long, 1.31" Diameter (Part No.D70741)
from
$13.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 15.63" Long, 1.25" Diameter (Part No.D70898)
from
$13.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12.50" Long, 1.22" Diameter (Part No.D70960)
from
$18.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25253)
from
$26.99
Product Features:
See More
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Popular 1991 Mitsubishi Mighty Max Belts and Hoses Categories
1991 Mitsubishi Mighty Max Belts and Hoses
You count on your 1991 Mitsubishi Mighty Max to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 52 Belts and Hoses ranging in price from $2.49 to $79.99, you’re sure to find everything you need for your 1991 Mitsubishi Mighty Max.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 10 different brands like Dayco, Gates, and Imperial. 1991 Mitsubishi Mighty Max Belts and Hoses start as low as $2.49!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 69 extensive product reviews on 1991 Mitsubishi Mighty Max Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Flex Radiator Hoses; EPDM Rubber, 23 Inch Long, 1.25 Inch Inner Dia. with 4.0 stars and Flex Radiator Hoses; EPDM Rubber, 11 Inch Long, 1.25 Inch Inner Dia. with 2.3 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1991 Mitsubishi Mighty Max below to get started!
Top-Rated Belts and Hoses Brands For Your 1991 Mitsubishi Mighty Max
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1991 Mitsubishi Mighty Max running right for years to come. In our inventory you’ll find brands like Dayco, Gates, Imperial, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 1991 Mitsubishi Mighty Max back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1991 Mitsubishi Mighty Max, and some of our most reviewed Dayco parts include:
from
$14.99
(8)
Flex Radiator Hoses; EPDM Rubber, 14.75 Inch Long, 1.25 Inch Inner Dia.
Lower Radiator Hoses
FAQs for 1991 Mitsubishi Mighty Max Belts and Hoses
What are the most purchased Belts and Hoses for the 1991 Mitsubishi Mighty Max?
Out of 52 Belts and Hoses for the 1991 Mitsubishi Mighty Max, the most popular in our inventory are:
from
$43.99
(6)
V-Belt Idler/Tensioner Pulley; Steel, 81mm Dia., 16.4mm Width, Grooves
Idler Pulleys
What are the top-rated 1991 Mitsubishi Mighty Max Belts and Hoses?
Top-rated Belts and Hoses for your 1991 Mitsubishi Mighty Max based on customer reviews/ratings are:
from
$19.49
(5)
Flex Radiator Hoses; EPDM Rubber, 23 Inch Long, 1.25 Inch Inner Dia.
“Replacing possibly damaged hose, secondary to overheating, and unknown age of the component.”
from
$27.49
(3)
Flex Radiator Hoses; EPDM Rubber, 11 Inch Long, 1.25 Inch Inner Dia.
“well satisfied”
from
$25.99
(1)
Molded Heater Hose; EPDM Rubber, 3/8 Inch Diameter, 9 1/4 Inch Length
“Fit was excellent”
