1991 Dodge Dakota Performance Ignition Products
More 1991 Dodge Dakota Performance Ignition Products
Find your specific 1991 Dodge Dakota original or aftermarket Performance Ignition Products below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 1991 Dodge Dakota Performance Ignition Products
MSD Ignition – Harness; Dodge/Chrysler; 98-03 (Part No.8884)
from
$66.99
This MSD to Dodge harness is designed to provide a splice free and simple installation of an MSD Ignition control to late model Dodge vehicles equipped with the coil.
Product Features:
See More
Product Features:
- Plug-In Harness w/Color Coded Wires
- No Cutting Or Splicing
- Quick Easy Installation
- Provides A Direct Plug-In Installation
- When Adding An MSD Ignition Control
Accel – Adp.Harness 98/Newer Mopar (Part No.140021AH)
from
$35.49
Allows you to directly plug into the ACCEL PN 140021 Super coil when being used on a 1998 to 2002 Dodge truck, or Jeep equipped with a distributor and the newer light grey Yazaki wire harness coil connector. No cutting or splicing is required.
Product Features:
See More
Product Features:
- Nice Clean Connection
- Easy Installation
Accel – High-Performance Ignition Coil – Direct OE Fit (Part No.140021)
from
$72.39
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Standard Motor Products SMP Uf-198
- MSD 8228
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
MSD Ignition – Coil; Chrysler Late Model; 90-96 (Part No.8228)
from
$72.09
When it comes to late model performance parts nothing beats bolt-on and direct connection components. These new bolt-in coils are designed with improved materials and windings to produce a stronger output. The MSD blaster coils is a direct replacement for late model dodges.
Product Features:
See More
Product Features:
- Direct performance replacement for late model Dodge vehicles
- Works w/Stock Ignition As Well As MSD Ignitions
- CARB E.O. Approved
- Improved mid range RPM power
- Connect to factory wiring
- Use PN 8877 harness for direct plug in install
MSD Ignition – Blaster 2 Coil: High Performance Ignition Upgrade (Part No.8202)
from
$49.99
If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.
Product Features:
See More
Product Features:
- Improved output coil for electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Alkyd tower w/high dielectric properties lessens carbon tracking
Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)
from
$186.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).
Product Features:
See More
Product Features:
- Glass Filled Polyester Case
- Longer Spark Duration
- Increased Performance
- No Energy Loss Due To Arcing
- Includes Brass Contact Terminal
MSD Ignition – Tach Adapter (Part No.8910)
from
$91.99
In some instances when you install an MSD ignition, the factory ECU may not be able to distinguish when the coil fires. This is the signal that is also responsible for firing the injectors (or the tachometer), which may cause a no-run situation. The dual channel ignition adapter simulates the original coil trigger signal thus allowing the ECU to properly trigger both the tach and fuel injection with the MSD DIS ignition installed. In most cases, the adapter plugs directly into the MSD’s harness. For vehicles using an MSD DIS-2 ignition, only one PN 8912 is required. For DIS-4 applications, two PN 8912’s are required.
Product Features:
See More
Product Features:
- Designed for non-current limiting ignitions
- Size Non-Current Limiting Ignitions
- Easy mounting and installation
- Simulates the coil signal
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Unilite Ignition Module (Part No.605)
from
$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Popular 1991 Dodge Dakota Performance Ignition Products Categories
1991 Dodge Dakota Performance Ignition Products
Maybe you’re in the middle of a full rebuild of that 1991 Dodge Dakota. Maybe you just need a couple of Performance Ignition Products. Either way, Advance Auto Parts has 8 different Performance Ignition Products in our inventory ranging from $30.49 to $186.99. That means you can find the exact parts or products you need to keep that 1991 Dodge Dakota running smoothly.
Performance Ignition Products are only as good as their brand. We stock 3 different brands to make sure you have plenty of trusted parts to choose from for your 1991 Dodge Dakota. Accel, MSD Ignition, and Mallory are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Performance Ignition Products for your 1991 Dodge Dakota, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.
So if you’re in the market for aftermarket Performance Ignition Products to keep your 1991 Dodge Dakota rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Performance Ignition Products Brands To Make Your 1991 Dodge Dakota Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 1991 Dodge Dakota demands trusted brand parts and products to keep it running. Many trusted brands of Performance Ignition Products make up Advance Auto Parts’ inventory, and all are ready to help make your Dakota the best it can be. Be sure to browse some of our top Performance Ignition Products brands and parts.
Popular Mallory Performance Ignition Products
We carry Mallory parts in our stock across Performance Ignition Parts categories, plus more. For a 1991 Dodge Dakota, our most popular Mallory Performance Ignition Products include:
Top 1991 Dodge Dakota Performance Ignition Products from MSD Ignition
MSD Ignition products are another trusted brand when it comes to Performance Ignition Products for your 1991 Dodge Dakota. Popular MSD Ignition parts include:
FAQs for 1991 Dodge Dakota Performance Ignition Products
What are the most purchased Performance Ignition Products for the 1991 Dodge Dakota?
Out of 8 Performance Ignition Products for the 1991 Dodge Dakota, the most popular in our inventory are:
