1990 Suzuki Samurai Differentials

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Suzuki Samurai
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and silicone.

Product Features:

• Fits Suzuki Samurai
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Suzuki Samurai
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

The Spartan locker by USA standard gear is a mechanical locker that fits inside a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect. This unit does use the stock side gears.

Product Features:

• Fits Suzuki Samurai
• Made from 9310 steel for added strength
• Works with stock side gears in standard carrier case

Mini Spool for ’86 to ’95 Suzuki Samurai and ’89 to ’00 sidekick (rear only) with 26 axles. Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

• Fits Suzuki Samurai
• Installs into a standard open carrier case
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Samurai Spartan locker cross pin long.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Suzuki Samurai
• Works with Spartan Locker or standard open spider gears
• Long shaft

Samurai Spartan locker cross pin short.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Suzuki Samurai
• Works with Spartan Locker or standard open spider gears
• Short shaft

Mobil 1 Synthetic Gear Lubricant LS 75W-90 is a supreme, multi-purpose automotive gear lubricant that helps to provide exceptional thermal stability and resistance to high temperature oxidation, extending gear life due to minimal deposits. Helps to deliver outstanding protection against low speed/high torque wear with the capability to handle severe driving conditions while delivering smooth efficient performance. Mobil 1 Synthetic Gear Lubricant LS provides exceptional shear stability, corrosion protection, and enhanced frictional properties. Compared to conventional hypoid gear lubricants, Mobil 1 LS 75W-90 performs exceptionally over a wide range of temperatures to reduce wear at start up. Mobil 1 gear lube helps to minimize leakage and reduce contamination while providing good resistance to foaming to maintain film strength for reliable lubrication. Meets or exceeds the requirements of the following industry specifications: API GL-5.

Product Features:

• Mobil 1 LS synthetic automotive gear lubricant exceeds the highest level of performance requirements of modern passenger vehicles
• Helps to provide exceptional thermal stability and resistance to high temperature oxidation and extend gear life due to minimal deposits
• Delivers outstanding protection against low speed/high torque wear, handling severe driving conditions with smooth, efficient performance
• Compared to conventional hypoid gear lubricants, performs exceptionally over a wide range of temperatures to reduce wear at start up
• Provides exceptional shear stability, corrosion protection, and enhanced frictional properties
• Manufacturer Part Number: 104361

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil

Suzuki Samurai crush sleeve. Approx 1.240″ long.

Product Features:

• Crush sleeve for Suzuki Samurai
• 1.240″ tall

8″ Toyota, 7.5″ GM, 8.2″ GM, 12T, pinion shim set, & Mazda truck.

Product Features:

• Pinion depth shim kit for Toyota 7.5″, 8″ and V6

Product Features:

• KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Suzuki Samurai pinion seal.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Suzuki Samurai

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: spring loaded; single-lip
• Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
• Excellent high temperature capabilities
• Compatible with wide range of fluids
• Delivers quality and reliable performance for every type of repair

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landrcuiser (fine spline pinion) & T100/Tacoma with factory locker. 30mm socket, M20 x 1.5 thread.

Product Features:

• Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landcruiser with 30 spline pinion and Tacoma/T100 with factory locker
• 20mm x 1.5 thread
• 30mm socket

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using high-quality materials for durability and performance
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Bearing race driver front Toyota 7.5″, 8″, Landcruiser, and the Suzuki Samurai. No return. (TOY30306).

Product Features:

• Bearing race driver
• Fits 30306 race
• All steel construction