1989 Chevrolet G10 Performance Engines

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

• Advance the cam for increased torque and horsepower
• Tune your powerband for more end torque or increase top end horsepower
• Includes (4) offset bushings and (1) 0 degree bushing
• Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
• Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
• Increase Top-End Horsepower

HYDRAULIC – Xtreme Energy: Very strong mid-range torque and throttle response, 2200+ stall.

Product Features:

• HYDRAULIC – Xtreme Energy: Very strong mid-range torque and throttle response, 2200+ stall.
• 274/286 Advertised Duration, 230/236 Duration @ .050″, .490″/.490″ Lift, 110 Lobe Separation
• Valve spring upgrade required
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Product Features:

• Replacement Gasket Set For PN[4242]

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Manufactured from cellulose and nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement, high performance street, drag race and oval track.

Product Features:

• Made of high temp silicone or nitrile blend rubber
• Torque limiters to prevent over tightening
• One piece molded rubber
• Fits left and right hand dipsticks

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Product Features:

• Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
• 3/8 inch-16 by 1 inch bolts
• Kit includes 12 bolts and washers
• Manufactured from high quality steel
• Bolts feature hex heads

SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Xtreme Energy Computer Controlled: Great in throttle body, crossfire or carbureted engine and 305 TPI.

Product Features:

• Cam and lifter kit for Small Block Chevy engines
• CL-Kit includes cam, lifters, assembly lube, instructions and decals
• HYDRAULIC – Xtreme Energy Computer Controlled: Great in throttle body, crossfire or carbureted engine and 305 TPI.
• 249/260 Advertised Duration, 206/212 Duration @ .050″, .434″/.444″ Lift, 112 Lobe Separation
• Valve spring upgrade required

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

• Has A Zinc Dichromate Finish
• Made Of High Quality Grade 8 Steel
• Has A Tall Hex Head To Prevent Wrench Slipping Off
• Extra Thick Parallel Ground Washer
• Washer Provides More Accurate And Uniform Torque

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• Complete Kit: Includes Retainers And Locks
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Includes Superior Quality Steel Retainers
• Includes 7 deg. Heat-Treated Valve Stem Locks
• Retainers and Locks Black Oxide Coated
• Non-Rotator Style: Dyno Tested and Street Proven
• Great Match to Edelbrock Camshaft Kit

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Die cut silicone rubber gaskets conform to out-of-flat covers
• Great for on-again/off-again situations
• Not intended for use in emission controlled vehicles.

VALVE SEALS, O-RING 11/32″ 1 ST

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Chevrolet V8 265-400 applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

• CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
• Designed for high performance street and race engines
• Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
• Additional clearance, up to 1.650″ O.D. valve spring

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

• Edge Molded Rubber Water Outlet Gasket Is Reusable
• Requires No Gasket Sealer
• Solid Aluminum Carrier For Strength/rigidity
• Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

Spectre’s chrome engine kits are designed to give the top of your engine an amazing look in one neat package. This chrome engine kit includes chrome valve covers, chrome valve cover bolts, a chrome dip stick and a chrome plated timing cover.

Product Features:

• Chrome valve covers
• Chrome valve cover bolts
• Chrome dip stick and tube
• Chrome timing cover
• Dresses up the engine
• Triple plated chrome

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

• 3/8″ Diameter, 7.800″ Length
• Magnum Pushrods for Small Block Chevy
• One-piece .080″ wall chromemoly steel tubing
• Heat-treated for extended durability and guide plate compatibility
• Precision formed and reinforced pushrod end

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Die-cut for an excellent fit
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

• Chrome Plated
• Grade 5
• AN washers with no exposed shoulder for a professional appearance

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

• Valve Spring Retainers for Use OE Cast Iron Heads
• Superior Quality Heat-Treated Steel
• Machined for Strength with Black Oxide Finish
• Finish Ensures Rust and Corrosion Protection

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 Deg Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Computer Chip Available – Return Card in Packaging
• Accepts All Factory Accessories
• Not for Vehicles with Flash Memory Computer
• Gains 6/10s of a Second in 10 to 70 MPH
• Stock Throttle Body Remains in Stock Position

Mr. Gasket cam locking plates feature a steel retainer plate designed to secure the cam gear bolts from coming loose and backing out, preventing costly engine damage. Retainer plate fits under bolt heads allowing tabs to be bent against hex head flats creating a secure positive lock.

Product Features:

• Black oxide finished steel
• Includes (3) grade 5 bolts & locking plate
• Fits Chevrolet Small and Big Block without OE roller cam
• Tabs bend up around bolt head to secure

This Mr. Gasket Rear Main Seal is made from Viton&reg: Rubber. This style of rubber can handle high temperature like silicone rubber, but with superior abrasion resistance. Its durability and it’s double, offset lip seal design make it recommended for applications that have high engine vacuum, like racing engines that utilize external vacuum pumps for crankcase evacuation.

Product Features:

• Repairs That Leaky Rear Main Sail
• Viton« Rubber Offers Both Abrasion Resistance & High Temperature Tolerance
• Viton® Rubber Offers Both Abrasion Resistance & High Temperature Tolerance
• Upgrade for Rope Seal Equipped Cars or Silicone Rubber Main Seals

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit