1988 Oldsmobile Cutlass Performance and Racing Products
More 1988 Oldsmobile Cutlass Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1988 Oldsmobile Cutlass, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1988 Oldsmobile Cutlass Performance and Racing Products
Edelbrock – Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire (Part No.5487)
from
$367.99Product Features:
- Designed for Optimum Torque and Acceleration
- Maximum Performance From Idle through Mid-Range
- Matched To Performer Intake PN[5486]
- Includes Hydraulic Lifters and Assembly Lube
- Major Improvement in Throttle Response and Torque
- Use For Daily Drivers/Trucks/Vans/RVs/4x4s
- Take The Guesswork Out Of Camshaft Selection
B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)
from
$665.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 3400-3800 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
B & M – Holeshot 3600 (Part No.20425)
from
$825.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
- Dual Pattern Drive Lugs
- New Turbine Hub
- New Springs/Rollers In Stator
Energy Suspension – Control Arm Bushing Set (Part No.3.3132R)
from
$154.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Energy Suspension – Control Arm Bushing Set (Part No.3.3133G)
from
$125.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1016)
from
$67.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
- Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
- Raises combustion sealing force to roughly three times that of standard head gaskets.
- Steel wire rings for the greatest combustion seal strength.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Head Gasket (Part No.1130G)
from
$32.99
Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.
Product Features:
See More
Product Features:
- Manufactured from .020″ steel shim stock.
- Thinner than composition head gaskets – increases engine compression.
- Stress formed embossments seal extreme cylinder pressures.
- For high performance street, drag race and oval track use.
Mr. Gasket – Ultra Seal: Oil Pan Gasket (Part No.5884)
from
$36.49
Manufactured from cellulose/nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For original equipment replacement, high performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile rubber composition gasket material
- Provides excellent sealing and durability
- Complete with molded rubber front/rear oil pan end seals where applicable
- For OE replacement, high performance street, drag race and oval track use
- Graphite Non-Wicking Rubber
- No Cork Particles
- Easy Removal For Disassembly
FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1814)
from
$30.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – PERFORMANCE VALVE COVER GASKET SET (Part No.1602)
from
$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Die cut silicone rubber gaskets conform to out-of-flat covers
- Great for on-again/off-again situations
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5861)
from
$37.99
Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are an extra thick .312 inch which can help with valvetrain clearance.
Product Features:
See More
Product Features:
- Manufactured from high-density cork /rubber blend gasket material
- A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
- Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
- For OE replacement, high performance street, drag race and oval track
- An extra thick .312″ which can help with valvetrain clearance
Accel – High Energy Ignition Coil for GM HEI – 1973-1991 (Part No.140003)
from
$100.99
Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Highly Specialized Silicone Magnetic Steel Cores
- Standard Motor Products SMP Dr-31
- MSD 8225
Accel – GM 1984-95 Remote Supercoil (Part No.140011)
from
$79.99
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Complete with new mounting hardware.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Highly Specialized Silicone Magnetic Steel Cores
- Standard Motor Products SMP DR-37
- MSD 8226
- Resist Corrosion
- W/New Mounting Hardware
Mr. Gasket – Rear Main Seal Gasket (Part No.1960)
from
$23.99
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.
Product Features:
See More
Product Features:
- Repairs That Leaky Rear Main Sail
- Silicone Rubber to Withstand Extreme Engine Oil Temperatures
- Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
- Injection Molded for Precise Fit
FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2900)
from
$21.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)
from
$134.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
Mallory – Distributor Wiring Harness (Part No.29349)
Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)
from
$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Energy Suspension – Tie Rod Dust Boot (Part No.9.13102G)
from
$5.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Energy Suspension – Control Arm Bushing Set (Part No.3.3169G)
from
$59.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Energy Suspension – Control Arm Bushing Set (Part No.3.3165G)
from
$57.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Energy Suspension – Control Arm Bushing Set (Part No.3.3168R)
from
$57.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Edelbrock – Performer Small-Block Oldsmobile 350 EGR Intake Manifold (Part No.3711)
from
$463.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Edelbrock – Performer Rover Intake Manifold for Buick/Olds 215 V-8 Engines (Part No.2198)
from
$411.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Edelbrock – Super Victor 4500 for Raised Port 23 Degree Intake Manifold Small-Block Chevy (Part No.2971)
from
$494.99
Product Features:
See More
- 3500-8000 RPM Range
- Single Plane Type-4500 Style Flange
- 6.77 in. Front Height, 6.77 in. Center Height, 6.77 in. Rear Height
- Satin Finish
- For Raised Port 23 Degree Heads
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2002)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-1001)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2001)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
Popular 1988 Oldsmobile Cutlass Performance and Racing Products Categories
1988 Oldsmobile Cutlass Performance and Racing Products
You count on your 1988 Oldsmobile Cutlass to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 20 Performance and Racing Products ranging in price from $5.99 to $766.99, you’re sure to find everything you need for your 1988 Oldsmobile Cutlass.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 8 different brands like K&N, Energy Suspension, and Accel. 1988 Oldsmobile Cutlass Performance and Racing Products start as low as $5.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 166 extensive product reviews on 1988 Oldsmobile Cutlass Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are GM 86-99 Dis Supercoil with 2.2 stars and Unilite Ignition Module with 5.0 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1988 Oldsmobile Cutlass below to get started!
Top-Rated Performance and Racing Products Brands For Your 1988 Oldsmobile Cutlass
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1988 Oldsmobile Cutlass running right for years to come. In our inventory you’ll find brands like K&N, Energy Suspension, Accel, and even more.
Popular K&N Performance and Racing Products
You’ll find popular K&N brand products across Performance Oil Filters. All are waiting to get your 1988 Oldsmobile Cutlass back on the road. Some of the top-rated K&N products in these categories are:
from
$17.99
(29)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
from
$17.99
(47)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
FAQs for 1988 Oldsmobile Cutlass Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1988 Oldsmobile Cutlass?
Out of 20 Performance and Racing Products for the 1988 Oldsmobile Cutlass, the most popular in our inventory are:
What are the top-rated 1988 Oldsmobile Cutlass Performance and Racing Products?
Top-rated Performance and Racing Products for your 1988 Oldsmobile Cutlass based on customer reviews/ratings are:
from
$85.29
(3)
Unilite Ignition Module
“I like the Unilite product because it is so small and compact compared to the HEI stuff I normally use. If you are restricted on space Its a great pro”
from
$18.29
(3)
PERFORMANCE OIL PAN GASKET SET
“This part is incorrectly listed as fitting a 2007 Pontiac Grand Prix. It’s not Advanced’s fault as EVERY shop and site has this part listed for that v”
