1988 Chevrolet Monte Carlo Performance Exhaust Products
More 1988 Chevrolet Monte Carlo Performance Exhaust Products
Find your specific 1988 Chevrolet Monte Carlo original or aftermarket Performance Exhaust Products below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 1988 Chevrolet Monte Carlo Performance Exhaust Products
Dynomax – Direct Fit Catalytic Converter: No Fabrication Needed, EPA Compliance (Part No.24235)
from
$99.99
DynoMax Race Bullet mufflers feature 100-percent welded construction for lifelong durability. The ‘Pure Unadulterated POWER’ and lightweight, compact design make it the ultimate race muffler. The unrestricted, straight-through design is dyno tested and t
Product Features:
See More
Product Features:
- Designed for vehicles with limited space
- Light weight compact design
- 100% welded design for maximum durability
- CRF Technology which helps provide up to a 4 dbA sound reduction, on most race applications, while maintaining a deep race tone
Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound (Part No.8042441)
from
$123.99
The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More
Flowmaster Inc. – 50 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, Non-Reversible, Moderate Sound (Part No.842553)
from
$175.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More
Flowmaster Inc. – Super 40 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.952548)
from
$133.99
The Super 40 features Flowmaster’s Delta Flow technology. It’s larger case profile provides the best of both worlds of performance and sound. The Super 40 has that deep powerful sound of the Original 40 series but with all the benefits of performance and low interior resonance from the Delta Flow technology. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound (Part No.942441)
from
$133.99
This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Flowmaster Inc. – Super 44 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound (Part No.942446)
from
$113.99
Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Flowmaster Inc. – 50 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Moderate Sound (Part No.942051)
from
$154.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Mr. Gasket – Alternator Bracket (Part No.5170)
from
$38.49
Original equipment style bracket in high quality chrome for years of service. Includes hardware.
Product Features:
See More
Product Features:
- Chrome Plated Heavy Gauge Steel
- Can Be Used For Other Applications
- Looks Better Than Painted
- Hardware included
Mr. Gasket – Alternator Bracket (Part No.9850)
from
$25.99
Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.
Product Features:
See More
Product Features:
- Chrome Plated Steel
- F-Style
- Heavy Gauge Steel Construction
- Fits Small Block Chevy 265-400 CID
- Must Be Used With Part 9852
Mr. Gasket – Header Bolt Set (Part No.2210G)
from
$41.99
Made of high quality stainless steel. These bolts will brighten up your hot rod, or improve the looks of your race car.
Product Features:
See More
Product Features:
- Bright Ball Burnish Finish
- Made From 304 Stainless
- Compact Hex Head Is Ideal Where Space Is Limited
- 12 Per Set
- Resist corrosion and provides a clean professional appearance
Mr. Gasket – Alternator Bracket (Part No.4954)
from
$19.29
These brackets are made from heavy gauge steel, polished to a high luster, then chrome plated. Similar in design to OEM units, these brackets can be adapted to other engines.
Product Features:
See More
Product Features:
- Chrome plated
- Similar to OEM design
- May be adaptable to other applications
Mr. Gasket – Header Bolt Set (Part No.2211G)
from
$50.39
Made of high quality stainless steel. These bolts will brighten up your hot rod, or improve the looks of your race car.
Product Features:
See More
Product Features:
- Bright Ball Burnish Finish
- Made From 304 Stainless
- Compact Hex Head Is Ideal Where Space Is Limited
- 16 per Package
- Resist corrosion and provides a clean professional appearance
Mr. Gasket – Alternator Bracket (Part No.5171)
from
$37.69
These brackets are made from heavy gauge steel, polished to a high luster, then chrome plated for lasting beauty, Similar in design to OEM units, these brackets can be adapted to other engines.
Product Features:
See More
Product Features:
- Replaced GM # 6262956
- Polished To High Luster
- Chrome Plated For Lasting Beauty
Spectre – Alternator Bracket (Part No.4719)
from
$30.99
This Spectre Alternator Bracket is an upper mount designed to fit 1969 and later Chevrolet Big Block engines with a long water pump. Featuring a triple chrome-plated finish and high quality steel construction, this part is an OEM replacement that mounts on the passenger’s side.
Product Features:
See More
Product Features:
- Fits Big Block Chevy engines with a long water pump from 1969 and later
- Manufactured from high quality steel
- Upper bracket for passenger side mounting
- Features a triple chrome-plated finish
- Stock replacement part
Dynomax – 89017 Exhaust System Kit (Part No.89017)
from
$259.99
Give your vintage vehicle’s exhaust system an upgrade with a DynoMax® dual header kit. Designed to attach with OE headers, it features a special reducer that allows for a variety of mounting options.
Product Features:
See More
Product Features:
- COMPATIBILITY — Designed for 1978-1987 midsize sedans such as Oldsmobile Cutlass, Chevrolet Monte Carlo, Buick Regal and Pontiac Grand Prix; see product information for compatibility and engine spec
- BUILD IT YOURSELF — Design and custom fabricate your own exhaust system with this kit that attaches to OE headers
- FLEXIBLE MOUNTING — Special reducer design allows for a variety of mounting options
- IMPROVED FLOW CAPACITY — Smooth bends improve flow capacity over traditional bends
- SPECS — Extra-long tailpipes with side exits with a full 2.25-in. diameter; tail pipes exit on each side of vehicle at rear bumper
- COMPLETE SOLUTION — Includes all the necessary clamps, hangers, flanges, gaskets, mounting hardware, intermediate, extension and tail pipes
- PREMIUM MATERIALS – Made from quality aluminized steel for durability and long life
- BETTER TOGETHER — Complete your system with premium DynoMax mufflers and DynoMax accessories for a complete performance exhaust system
- WARNING — Not legal for use on pollution-controlled motor vehicles; headers are for racing use only and not intended or applicable for highway use
Flowtech – Real-Seal; Header Gasket (Part No.99153FLT)
from
$85.39Product Features:
- Water/Weather Resistant
- Re-Useable
- Will Not Burn Or Blow Out
- Suitable For Port-Matching
- Made In USA
Mr. Gasket – Mls Exhaust Gasket (Part No.4805G)
from
$49.49
Multi-Layered Steel (MLS) exhaust and header collector gaskets are designed for extreme cylinder pressures produced by high horsepower high compression turbo-charged, supercharged and nitrous oxide injected engines. Manufactured from three stainless steel layers, they resist corrosion, will not burn through or push out and maintain maximum fastener torque retention. Stress formed inner and outer layer embossments act like springs that rebound under exhaust flange clamp load, creating force to seal extreme exhaust pressures. Total gasket thickness .075 inch. Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.
Product Features:
See More
Product Features:
- Multi Layer Stainless Steel 3-Layers
- Round Port 1.75″ Diameter
- Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.
- Thickness .072″
- Fits GM LS Series Engines 1997-’15
Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5901)
from
$31.99
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Withstands Intense Exhaust Heat
- Graphite-Impregnated Facing
- Steel Expanded Metal Core
- Superior Tensile Strength
- Resists Deteriorating
- Anti-stick Properties
- Easy Removal For Disassembly
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1410)
from
$37.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1411)
from
$42.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Exhaust Manifold Gasket -Performance (Part No.5906)
from
$45.99
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Manufactured from high-temperature steel core/graphite faced exhaust material
- Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
- Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
- Conforms to and seals minor surface irregularities
- Can be trimmed if necessary for modified port applications
- For OE replacement, high performance street, drag race and oval track use
- Anti-Stick Properties
- Easy Removal For Disassembly
Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5908)
from
$45.99
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Manufactured from high-temperature steel core/graphite faced exhaust material.
- Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
- Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
- Conforms to and seals minor surface irregularities
- Can be trimmed if necessary for modified port applications
- For OE replacement, high performance street, drag race and oval track use
- Anti-Stick Properties
- Easy Removal For Disassembly
Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5912)
from
$38.49
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Has A Graphite Core W/ Steel Outer Layers
- Graphite Core Has Excellent Thermo-conductivity
- Coated With High Temp Silicone For Sealing
- Will Not (brindle ) Or Indent Aluminum Heads
Hooker Headers – Super Competition Header Gasket (Part No.10809HKR)
from
$23.29
Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.
Product Features:
See More
Product Features:
- Tear Resistant
- Precisely Cut To Match Header
Edelbrock – Exhaust Manifold Gasket Set for Chevrolet (Part No.7205)
from
$31.99
Product Features:
See More
- Designed To Match Port Openings Of Cylinder Heads
- Excellent Free-Flowing Seal
Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5903)
from
$37.69
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Manufactured from high-temperature steel core/graphite faced exhaust material
- Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
- Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
- Conforms to and seals minor surface irregularities
- Can be trimmed if necessary for modified port applications
- For OE replacement, high performance street, drag race and oval track use
- Anti-Stick Properties
- Easy Removal For Disassembly
Mr. Gasket – Exhaust Gasket Set (Part No.152)
from
$36.49
Mr. Gasket’s Performance Header Gaskets are manufactured from a heavy duty high-temperature material, .062 inch? thick, consisting of an acrylic binder system to resist high temperature. Provides excellent sealing and durability with maximum torque retention to eliminate gasket failure. While precision die-cut for an excellent fit, it can be trimmed if necessary for modified port applications. For OE replacement, higher performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Provides excellent sealing and durability.
- Precision die-cut for an excellent fit
- Manufactured from high-temperature acrylic blend exhaust material
- Can be trimmed if necessary for modified port applications
- For OE replacement, high performance street, drag race and oval track use
Hooker Headers – Super Competition Header Gasket (Part No.10846HKR)
from
$17.79
Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.
Product Features:
See More
Product Features:
- Tear Resistant
- Precisely Cut To Match Header
Popular 1988 Chevrolet Monte Carlo Performance Exhaust Products Categories
1988 Chevrolet Monte Carlo Performance Exhaust Products
Maybe you’re in the middle of a full rebuild of that 1988 Chevrolet Monte Carlo. Maybe you just need a couple of Performance Exhaust Products. Either way, Advance Auto Parts has 14 different Performance Exhaust Products in our inventory ranging from $20.99 to $259.99. That means you can find the exact parts or products you need to keep that 1988 Chevrolet Monte Carlo running smoothly.
Performance Exhaust Products are only as good as their brand. We stock 5 different brands to make sure you have plenty of trusted parts to choose from for your 1988 Chevrolet Monte Carlo. Mr. Gasket, FEL-PRO Performance, and Flowtech are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Performance Exhaust Products for your 1988 Chevrolet Monte Carlo, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 21 reviews in this category, some of the top rated parts include Real-Seal; Header Gasket with 5.0 stars.
So if you’re in the market for aftermarket Performance Exhaust Products to keep your 1988 Chevrolet Monte Carlo rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Performance Exhaust Products Brands To Make Your 1988 Chevrolet Monte Carlo Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 1988 Chevrolet Monte Carlo demands trusted brand parts and products to keep it running. Many trusted brands of Performance Exhaust Products make up Advance Auto Parts’ inventory, and all are ready to help make your Monte Carlo the best it can be. Be sure to browse some of our top Performance Exhaust Products brands and parts.
Popular Flowmaster Inc. Performance Exhaust Products
We carry Flowmaster Inc. parts in our stock across Performance Exhaust Mufflers categories, plus more. For a 1988 Chevrolet Monte Carlo, our most popular Flowmaster Inc. Performance Exhaust Products include:
from
$133.99
(1)
40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound
Performance Exhaust Mufflers
Top 1988 Chevrolet Monte Carlo Performance Exhaust Products from Mr. Gasket
Mr. Gasket products are another trusted brand when it comes to Performance Exhaust Products for your 1988 Chevrolet Monte Carlo. Popular Mr. Gasket parts include:
from
$20.99
(14)
Performance Exhaust Gasket Set for Enhanced Sealing and Durability
Performance Exhaust Manifold Gaskets
FAQs for 1988 Chevrolet Monte Carlo Performance Exhaust Products
What are the most purchased Performance Exhaust Products for the 1988 Chevrolet Monte Carlo?
Out of 14 Performance Exhaust Products for the 1988 Chevrolet Monte Carlo, the most popular in our inventory are:
from
$31.99
This product is not rated
Ultra Seal: Exhaust Gasket Set
Performance Exhaust Manifold Gaskets
What are the top-rated 1988 Chevrolet Monte Carlo Performance Exhaust Products?
Top-rated Performance Exhaust Products for your 1988 Chevrolet Monte Carlo based on customer reviews/ratings are:
