from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$173.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits GM 8.5″ rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$28.49

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$8.49

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$232.99

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

from

$186.99

Product Features:

FULL SPOOL DANA 60 35 SPLINE 4.10 & DOWN

from

$5.49

Product Features:

CRUSH SLV 8 7/8 12BLT TRK

from

$206.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits GM 8.5″ rear
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$10.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$7.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$57.99

Pilot bearing for 10.5″ 14 bolt truck, 2.050″ O.D.

Product Features:

Pilot bearing
Fits GM 10.5″ 14 bolt truck
2.050″ O.D.

from

$16.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$27.49

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$89.99

Standard Open cross pin shaft for four pinion design for GM 14T.

Product Features:

Cross pin shaft
Fits GM 10.5″ 14 bolt truck

from

$18.09

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1964-1970 Chevrolet 8.2 inch 10 bolt & 1970-1981 GM 8.5 inch ring gear

Product Features:

.047″ thick cellulose/nitrile composite gasket material
Precision die cut
Reusable

from

$23.99

Product Features:

Cross pin bolt
Fits GM 9.5″ and 9.25″ IFS

from

$179.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$5.99

DiffrlPinSupportBolt

from

$41.99

Product Features:

Shim kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction

from

$29.99

9.5″ GM differential carrier Supershim kit.

Product Features:

Super carrier shim kit for GM 9.5″
Interlocking design makes installation much easier

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$139.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$9.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$10.99

14T ring gear bolt 4.11 & down. 9/16″ x 18. 2.085″ overall length.

Product Features:

Ring gear bolt for GM 10.5″ 14 bolt truck
4.11 and down ratio
1/2″ x 18 thread
2.085″ overall length

from

$1025.00

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits GM 9.5″
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$8.29

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!