Name: Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads
Brand: Edelbrock
SKU: 5703
Price: 65.99 USD

from

$65.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$17.99

Product Features:

For Small-Block Chevy
One Piece Configuration
Includes Front Cover Gasket & Front Seal
Includes Necessary Gaskets & Crankshaft Oil Seal
For Replacement Or Installation

from

$850.99

Holley designed these throttle bodies with all relevant emission provisions and hook-ups for a true 50 state legal installation. They are engineered for a bolt-on installation on stock factory Manifolds for the applications cataloged. The one barrel throttle bodies have been assigned California Air Resources Board (C.A.R.B.) Executive Order (E.O.) number D-115-4. The two barrel throttle replacement bodies are considered to be the functional equivalent of the original equipment throttle body and, as such, are considered to be 50-State legal.

Product Features:

Direct Replacement For OE Units
2 in. Throttle Bore
42 percent Area Increase Over Stock TBI
Including Air Distribution Ring
Increased Torque and Horsepower
50 State Legal

from

$7.99

Spectre’s Harmonic Balancer Bolt Kit is designed to fit Chevrolet Small Block 265-400 V8 engines. This grade 8 bolt is 2-1/2 inches long, and features a plated finish for corrosion resistance. This kit also includes a security lock washer.

Product Features:

Fits Chevrolet Small Block 265-400 V8 engines
Features a corrosion resistant plated finish
Gold iridite finish
Grade 8 bolt, 7/16 inch-20 by 2-1/2 inches
Includes security lock washer

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$587.99

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:

Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
Best with aftermarket converters and more rear gear.
Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

from

$42.49

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .187 inch thick. Fits Chevy 5.0, 5.7L Vortec V8 with center bolt valve covers.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track

from

$63.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
Not intended for use in emission controlled vehicles.

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$102.99

Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.brbrA typical MLS head gasket requires a smoother (30Ra) surface finish than composite head gaskets. Mr. Gasket’s proprietary polymer coating will seal a surface finish twice as rough (60Ra) as a typical MLS head gasket. For high performance street, drag race and oval track use.

Product Features:

Gasket bore – 4.165 inch: Compressed thickness – .040 inch
Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
Optimized sealing embossments seals extreme cylinder pressure
Provides excellent stability and reduces cylinder bore distortion.
Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
For high-performance street, drag race and oval track use

from

$80.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
For OEM Hydraulic Roller Lifter Cams Only

from

$429.99

Torque Converter – Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) APPLICATION: Tork Master 2400 for GM 1993 to 1996 TH700R4 (30 spline) 1984 to 1993 and 4L60E (30 spline) The Tork Master is B&M’s lowest cost pe

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$323.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$306.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$94.99

Manufactured from high quality machine finished aluminum, Spectre’s Throttle Body Spacers are engineered to improve engine performance. By providing added volume to the intake manifold and directing air through a tapered internal constriction, this spacer utilizes the Venturi effect to increase the speed of air flowing into your intake manifold. Spectre has designed a number of kits to fit a wide range of specific applications. Each kit includes the necessary gaskets and hardware to bolt directly to the factory components, making installation quick and easy.

Product Features:

Includes the necessary gaskets and hardware to bolt directly to the factory components
Each kit is designed for the applications listed
Manufactured from high quality machine finished aluminum
Can be installed in less than an hour using common hand tools with no drilling or cutting required
Simple to install

from

$494.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
All Factory Connections Used
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal with OEM Throttle Body
For OE and Small Bore TBI Injectors Only
No Chip Changes/Computer Modifications Required
5.7L Power Package Provides Free Computer Chip

from

$27.49

These grade 5 hex head bolts are black coated plated for protection and appearance. Hardened flat washers provide uniform torque and prevent galling on aluminum manifolds.

Product Features:

Assures Accurate Torque App
Prevents Galling Manifold
Grade 5 Material
Black Oxide Coasted

from

$34.99

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use
Creates Tight Leak proof Seal

from

$42.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use

from

$435.99

Edelbrock #8827 Water Pump small block Chevy cartridge style race ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling

Product Features:

Standard Impeller Rotation
0.750 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.8125 in. Block To Hub Height
Satin Finish

from

$215.99

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$203.99

Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:

7.25 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.