1987 Chevrolet Blazer Performance Fuel Systems

CARQUEST premium remanufactured fuel injection pumps are completely torn down, ultrasonically cleaned, inspected and remanufactured using premium components. Each pump is tested on a sophisticated flow bench under multiple operating parameters.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Edelbrock Performer RPM Series fuel pump for SBC and W Series Chevy, 1721.

Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.

Edelbrock Performer RPM Series fuel pump is for Big-Block Chevrolet, 1722.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

These universal in-line fuel pumps are intended for fuel Injection systems. They are designed to work in-line, not inside the tank, so installation is a snap. They’re all rated for continuous duty service and have been tested up to 2,500 hours.

Keith Dorton Series VoluMax race series fuel pump made from heavy duty construction for continuous high RPM operation. Redesigned high flow valves always ensure adequate fuel delivery. Fuel pressure regulator is required. Fuel body casting can be rotated to accommodate various plumbing situations. High output fuel flow, flows 170 gph free flow. Shutoff pressure pre-set at 8 PSI, 3/4-inch-16 inlet and outlet ports. Fittings not included.

Precision cut to cover stock fuel pump opening when converting to an electric fuel pump. Gasket included.

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

“Edelbrock part #1712 Victor Series fuel pump is for Big-Block Chevrolet. The Edelbrock Victor Series fuel pump is a must for drag racing, circle track racing, street machines or any application that demands a high-volume fuel delivery, these fuel pumps feature a high quality three stage polished finish. High-volume 3/8″” NPT inlet and outlet orifices surpass the capacity of conventional models. Produces 10 psi and must be used with an external fuel pressure regulator such as our Fuel Pressure Regulator #8190 or #1727. For gasoline only. Clockable lower housing can be rotated in 60 Deg Increments for best inlet/outlet alignment.”

Ideal for mounting a stock original equipment pump. The mounting plate is precision cut to cover the stock fuel pump opening and is complete with gasket.

New for Sniper 2 is the optional Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12-volt source is all that’s required from your vehicle to power the PDM and your Sniper EFI.

Make your classic drive like a modern fuel-injected vehicle, including easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley’s comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine and the system will begin self-tuning with no laptop or tuning experience required.

If you’re looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI.

Not only does the Sniper EFI 2GC offer superior throttle response and WOT power over the carburetor, but you may also benefit from increased fuel economy! Put an end to cold start issues, hesitations, vapor lock, and flooding with the accuracy of EFI. You can also use the Sniper EFI 2GC to control the ignition timing, taking EFI to the next level.

New for Sniper 2 is the optional Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12-volt source is all that’s required from your vehicle to power the PDM and your Sniper EFI.

If you’re looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI.

Make your classic drive like a modern fuel-injected vehicle, including easy cold starts, smooth drivability, and improved fuel economy! Sniper 2 is designed to be installed at home in your garage with limited tools and the support of Holley’s comprehensive installation manual and videos. The user-friendly setup wizard allows you to answer a few simple questions about your engine and the system will begin self-tuning with no laptop or tuning experience required.

Not only does the Sniper EFI 2GC offer superior throttle response and WOT power over the carburetor, but you may also benefit from increased fuel economy! Put an end to cold start issues, hesitations, vapor lock, and flooding with the accuracy of EFI. You can also use the Sniper EFI 2GC to control the ignition timing, taking EFI to the next level. The Sniper EFI 2GC system is capable of supporting 350 HP on naturally aspirated engines. Upgrade to Sniper EFI today!.

“You don’t have to be a computer wiz or tuning professional to run a sniper kit on your build. Simplicity is what we strive for! Our calibration wizard allows you to just answer a few questions about your engine and the system will begin self-tuning with no laptop required. Use the high resolution 3.5″” full color touchscreen for tuning and gauge displays. The stealth 4150 also includes transmission kick down provisions for GM TH350/400, 200R4/700R4 and Ford C4/C6 applications.”

Introducing the next generation of Holley EFI Dual Sync Distributors, the new design features an improved shutter wheel, high-quality dual Hall Effect sensors, and an MSD cap and rotor. While these distributors are designed to be used primarily in sequentially injected installations, you can easily use them as a crank trigger for TBI system also. The precision machined shutter wheel design ensures accurate timing, even at very high engine speeds. The Gen 2 Dual Sync also included a QPQ coated shutter wheel for superior corrosion resistance, and the wheel has been pinned and welded to the shaft for increased reliability. These distributors can also be used with other EFI systems that support Hall Effect crank and cam sensor inputs. Do you need to a bronze gear for your billet cam, No problem, these distributors maintain MSD shaft diameters, making it easy to source a bronze gear.

If you’re looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI.

Holley’s Sniper Stealth 4150 Master Kit gives you carburetor styling but functions just like the Sniper! A 4150 stealth is a great way to upgrade your ride to fuel injection in a cost-efficient way with just 4 simple connections required. Take your build to the next level and take advantage of improved engine performance, better MPG’s and easier starting. This kit supports up to 650hp naturally aspirated and 600hp boosted with Four 100 Lb./Hr injectors!.

If you’re looking for a high-performance fuel injection system that delivers power, efficiency, and ease of use, look no further than the Sniper 2 EFI.

New for Sniper 2 is the optional Power Distribution Module (PDM). This cost-effective and optional accessory isolates the core of your EFI and ignition wiring into one, easy-to-use location. Simply slide the stripped wire ends under the positive lock connector and tighten down the set screw. Battery and a switched 12-volt source is all that’s required from your vehicle to power the PDM and your Sniper EFI.