1987 Buick LeSabre Performance Ignition Products

Product Features:

• Service Part
• Makes Connections Quick And Easy

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

This unit permits a seamless wide range of adjustment to both amount and rate of ignition advance. This unit helps increase horsepower and throttle response. It provides maximum spark advance while preventing detonation or “pinging”. This kit includes an allen wrench for easy adjustment along with instructions.

Product Features:

• Adjustable Vacuum Advance
• Increases Horsepower And Throttle Response
• Includes Allen Wrench For Adjustments
• Instantly Increase Horsepower
• Maximum Possible Spark Advance
• Not Legal For Sale/Use In CA

Re-engineered to be the only true performance AC/Delco style DIS coil. “”Raised Dome”” construction, section bobbin technology, highly specialized silicone magnetic steel core, optimized windings, resistance, and turns ratio result in higher energy and voltage outputs, and longer dwell. Compatible with OE computer controlled ignition systems as well as Crane or MSD capacitive discharge DIS ignition systems. Brass contact increases energy transfer and resists corrosion better than aluminum. High dielectric strength “”ACCEL Yellow”” over molded housing. Packaged as single unit: 4 cyls require 2 coils, 6 cyls require 3 coils and 8 cyls require 4 coils.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP Dr-39
• MSD 8224
• Resist Corrosion

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

• Oil Filled For Better Cooling
• Optimized Low Resistance
• Silicon Magnetic Steel E-Core
• Higher Energy/Voltage Outputs
• Quicker Starts
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP Dr-31
• MSD 8225

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Complete with new mounting hardware.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP DR-37
• MSD 8226
• Resist Corrosion
• W/New Mounting Hardware

Stock style replacement modified HEI coil dust cover. Used on 8 cylinder vehicles only.

Product Features:

• Externally mounted coil
• Increases reliability
• Increase performance
• High quality plastic
• Resist spark loss
• Use brass conductors
• Low resistance connections
• No modifications

The updated Fuel Pump Booster is an easy way to maintain the proper fuel pressure on your car after adding a power adder such as a turbo or supercharger. The new model allows you to make your boost adjustments through a PC for improved control and accuracy. The Booster ensures that the engine receives the fuel it needs to make up for the increase in air being pumped into the intake manifold. It will increase the voltage to the factory fuel pump in proportion to manifold boost pressure in order to maintain the proper fuel delivery. The amount of increase is adjustable from a range of an additional 1.5 -22 volts up to 30 psi which can all be set and adjusted from your PC with MSD’s easy to use Windows based software. The MSD Booster will wire to the factory fuel pump relay or with a secondary booster pump.

Product Features:

• Direct performance replacement
• For GM 2 Tower Coils Used From Mid 1980s To Late 1990s
• 80:1 turns ratio
• Lower Primary Resistance Produces High Voltage Output
• Works w/Stock Ignition As Well As MSD Ignitions
• CARB E.O. Approved

These ACCEL carbon and graphite core wire sets virtually eliminate RFI noise, while providing maximum conductivity for ultimate performance in any race or street application. Double silicon insulation eliminates leakage and misfire.

Product Features:

• Heavy Duty 8.8mm Oversized Silicone Jacket
• 500 Ohms/ft. Of Resistance
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

• 8.8mm Graphite Suppression
• Silicone Spark Plug Boots
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

• 8.8mm Graphite Suppression
• Silicone Spark Plug Boots
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Less than 50 ohms per foot for superior spark
• Ferro-magnetic impregnated core creates an effective EMI choke
• 40 ft. Of Conductor Wound Into A Single Foot Of Wire
• For high EMI suppression
• Conductor core features Dupont Kevlar material
• Proprietary compound sleeves for resistance to high heat/abrasion