1987 BMW M6 Brake Parts

Brakes are designed as a system and all the parts need to work together for best performance. The boot and square cut seals included in our Caliper Repair Kit, ensure that the caliper works as designed during the apply and release cycle.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Increases the life span of the brake pads
• Restores brakes to like-new performance
• Prevents noise and premature wear
• Direct replacement for a proper fit

Nut

Carquest Premium Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

• Application-specific formulations designed for extended pad life and clean wheels
• Multi-layer shim for near silent braking
• OE designed slots and chamfers for consistent performance
• Hardware included on popular and late-model applications

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

• Wearever Brake Shoes come bonded or riveted based on OE design.
• Wearever Brake Shoes are coated to prevent rust.
• Wearever Brake Shoes are 100% New not remanufactured.
• Brand may vary by location

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

• Short closing paths
• Low volume uptake
• High efficiency
• Low throttling / after-suction resistance
• Low pressure differential between primary and secondary circuits
• Good bleedability
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)
• Central valve version suitable for ABS
• Compact design – ideal for installation in small spaces
• Reduced weight – by roughly 20% compared to conventional central valve technology
• Fewer components – almost half as many as compared to conventional technologies
• Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
• Low volume uptake – minimized elastic deformations due to smaller seals
• Sealing cups supported in the housing – robustness against soiling and wear; longer life
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

• Each unit is 100% new, providing consistent performance when servicing your brake system
• Easy to transfer for on-the-spot master cylinder bleeding
• Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
• Easy to clean to ensure no cross contamination
• Durability for long lasting performance

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

• Triggers a warning light on the dashboard
• Should be replaced each time the brake pad is replaced
• Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features:

• Reduced cost
• OE Quality
• Complete Kit

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

• 100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
• Exclusive rust-prohibitive finishing process extends unit life.
• Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
• All units are 100% tested to ensure reliable performance.
• Guaranteed fit and function.

Brake Reservoir Cap

The ATE Caliper Guide Pin is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

This disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles
• Ideal solution – this kit provides is a reliable replacement for original hardware that has stripped
• Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers. Mounted on side of brake pressure regulator. Fine thread pitch.

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers. Mounted on top of brake pressure regulator. Coarse thread pitch.

The Brembo brand has a range of over 1,600 items, which covers a remarkable 98% of all passenger cars and commercial vehicles on the roads in Europe today. Brembo manufactures an OE-Quality Brake Disc that assures maximum performance and enhanced driving comfort and offers with its aftermarket rotors the same levels of quality, technology and performance that are found in many of the prestigious OEM fitments. PVT pillar venting technology: (Vented Rotors Only) Brembo PVT discs feature the exclusive pillar venting system patented by Brembo, which improves cooling capacity and increases resistance to thermal cracking by over 40%. Fixing screw kits: discs are supplied with all the necessary fixing hardware for simpler, more efficient and safer installation

Product Features:

• OE-Equivalent and a direct fit replacement
• Made of special cast iron with high carbon content
• Pillar Venting Technology (Vented Rotors Only)
• Easy Check wear indicator system
• Provides a higher friction coefficient.
• Resistant to vibrations and noise.

The Zimmermann Formula Z brake disc was designed with the aim of teaming simple installation with optimum braking effect under high mechanical and thermal load. The compound brake disc developed by Zimmermann accommodates the increased demands incurred by engine tuning and optimized chassis structures. COAT-Z – Coat-Z is a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Formula Z – Bake Disc – The composite or compound brake disc named Formula Z is suitable for motorsport applications due to its special design. In contrast to the fully cast-iron brake disc, the friction ring (cast iron) and hub (aluminum alloy) are connected by steel pins. The resulting, floating construction reduces the thermal buffering of the friction ring in the operating temperature state substantially, because the friction ring can freely expand under thermal stress (e.g. when braking from high speeds or several consecutive brake applications). The use of aluminium alloy also considerably reduces the unsprung masses on the vehicle. Material quality / high carbon – Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

• Excellent deceleration action and no distortion of friction ring at high temperatures
• Substantial weight saving and therefore less unsprung mass
• Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
• Hot spots prevented by optimized design of ventilation channels
• 1:1 exchange of original disc possible
• Not subject to registration: general ABE certification supplied with disc
• No conversion required for brake tuning

For over 25 years Hawk Performance has been producing premium friction products that stop you faster and last longer. Whether you are looking to cut seconds off of your track time, need additional stopping power for your large vehicle, want a product that is cleaner and quieter or, just don’t want to have to think about brakes and rotors, Hawk Performance has the products to keep you safer. We leverage our experience on the track and the technology used in aerospace and the military to make the best brake pads and rotors for all of your vehicle’s needs. Our extensive Research & Development department, including a PhD in friction and 23 dynamometers, allows us to produce first class products in the USA.

Product Features:

• Low to mid temperature range
• Fade resistant
• Smooth & predictable torque
• Ideal for Autocross & club racing events
• All Hawk Performance compounds are not compatible with carbon ceramic rotors. Hawk pads are designed to work with Iron/Metal rotors.

Akebono EURO® Ultra-Premium ceramic brake pads provide exactly the ideal vehicle control and performance response intended by the manufacturers of European makes. Maintain the enhanced pedal feel of European braking performance with brake pads and friction formulas engineered specifically for your vehicle and manufactured in the USA. Brake Pads That Ensure Optimal Responsiveness and Cleaner Wheels European car owners across North America now have a brake pad solution that will keep their wheels virtually free from dust and provide the European stopping power they expect. The use of our exclusive, highly advanced ceramic brake pad technology means that Akebono’s EURO Ultra-Premium brake pads provide excellent stopping power while extending rotor life and virtually eliminating brake dust, so the wheels on your European vehicle will remain their cleanest. In addition, Akebono EURO Ultra-Premium ceramic brake pads control noise, vibration, and harshness (NVH) and help ensure longer rotor life. They are the ultimate upgrade for semi-metallic and low-metallic brake pads. Akebono: The Industry Standard for European Manufacturers For over two decades, Akebono Ceramic Technology® (ACT) has been standard on many of North America’s passenger cars, light trucks, and SUVs and has set the benchmark for ceramic pads used in OE vehicle production. Now European manufacturers request Akebono brake products, and we can deliver that level of reliability to your replacement brake pads. Akebono manufactures replacement disc pads that contain the same materials, engineering, quality standards, and advanced technologies used to create our original ceramic brake pads. The use of Akebono ceramic brake pads ensures customer satisfaction and eliminates unnecessary return visits to the shop.

Product Features:

• Ultimate upgrade for OE semi-metallic, organic and low-metallic brake pads
• Ultra-Quiet – controls noise, vibration and harshness level
• European braking performance with enhanced pedal feel
• Extremely rotor friendly for longer rotor life
• Friction formulas specially designed for European vehicles

The AMA/URO Stop Light Switch is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• Premium aftermarket replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

This wheel disc hardware kit includes rubber components used to protect the caliper pins or bolts. Worn or cracked rubber components will allow excessive movement of guide pins or bolts.

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. A complete brake job that includes new hardware goes a long way toward preventing comebacks. Changing out your Rubber Pin Boot or Slider Bushing Kit will ensure the guide pins are clean and free from debris for smoother braking.

Product Features:

• This part matches Original Equipment (OE) quality specifications
• Easy and fast replacement
• Prevents noise and premature wear
• Provides longer brake life and performance

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

Highest mechanical stability under load, highest compressive strength and resistance ATE/Continental has been contributing hydraulic brake hose assemblies for the automotive industry since the 1920’s. With an annual production of approximately 40 million brake hose assemblies, ATE/Continental is one of the world leaders in this sector today. As a full brake system supplier, ATE/Continental distinctively places its direct knowledge of overall hydraulic brake design into this product. The complete OEM experience, coupled with the specialized technology of an OE world market leader, uniquely places ATE/Continental near the top for brake hose assemblies with their ATE brand. ATE brake hoses are suitable for all brake fluids (DOT 3, DOT 4, DOT 4 LV, DOT 5.1)

Product Features:

• More than 70 braiding machines for braid production.
• Autoclaves or vulcanizing presses, and automatic surface control for the production of the inner and outer rubber layers.
• Primary use of extruded connectors.
• Test stands and laboratories are abundantly available for assured accuracy in satisfying the rigid criteria of all customer specifications.
• Outstanding quality standards with compliance certifications for FMVSS106 on our ATE brake hose assemblies, as well as ISO 14001 certification for production.
• In-house ATE N standards that exceed the legal requirements. Original ATE Brake hoses – Presentation

All WBR hydraulic hoses are manufactured to match the exact OE fit, OE construction, to ensure quick and easy installation, as well as trouble-free functionality for the life of the hose. WBR brake hoses are suitable for all brake fluids (DOT 3, DOT 4, DOT 4 LV, DOT 5.1)

Product Features:

• Excellent pulse strength for use on vehicles with ESP, ABS, DSC and ASR
• Very high ozone resistance, temperature change resistance and so a long service life
• Low water permeation and so extended service life of the brake fluid
• Use of robust hose valve connections and additional safety and shrink-fitted hoses in various materials.

Highest mechanical stability under load, highest compressive strength and resistance ATE/Continental has been contributing hydraulic brake hose assemblies for the automotive industry since the 1920’s. With an annual production of approximately 40 million brake hose assemblies, ATE/Continental is one of the world leaders in this sector today. As a full brake system supplier, ATE/Continental distinctively places its direct knowledge of overall hydraulic brake design into this product. The complete OEM experience, coupled with the specialized technology of an OE world market leader, uniquely places ATE/Continental near the top for brake hose assemblies with their ATE brand. ATE brake hoses are suitable for all brake fluids (DOT 3, DOT 4, DOT 4 LV, DOT 5.1)

Product Features:

• More than 70 braiding machines for braid production.
• Autoclaves or vulcanizing presses, and automatic surface control for the production of the inner and outer rubber layers.
• Primary use of extruded connectors.
• Test stands and laboratories are abundantly available for assured accuracy in satisfying the rigid criteria of all customer specifications.
• Outstanding quality standards with compliance certifications for FMVSS106 on our ATE brake hose assemblies, as well as ISO 14001 certification for production.
• In-house ATE N standards that exceed the legal requirements. Original ATE Brake hoses – Presentation

This automotive brake hydraulic hose was precision-engineered to match the fit, function and performance of the original brake hose on specific vehicles and positions to ensure safe, long-lasting durability as part of a complete brake repair.

Product Features:

• Ideal replacement – precision-engineered to match the performance of the original brake hose on specific vehicles
• Position-specific – manufactured to precise measurements to provide an exact fit and easy installation
• Quality assured – materials tested to exacting government-regulated safety and durability standards
• Durable design – made with EPDM rubber and specially coated, corrosion-resistant fittings