1986 Pontiac Firebird Drivetrains
More 1986 Pontiac Firebird Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1986 Pontiac Firebird, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1986 Pontiac Firebird Drivetrains
Driveworks – Taper Bearing Set (Part No.S-A-6)
from
$10.29
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – Yoke For GM 7.5" (Mech 3R) In A Triple Lip Design (Part No.41090)
from
$184.99
Yukon yoke for GM 7.5″ (mech 3R) in a triple lip design. 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring. This yoke uses inside clips. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits GM 7.5″ and 7.625″
- 27 spline
- Mechanics 3R u-joint size
- Inside snap ring design
- 2.556″ snap ring span
- 1.125″ cap diameter
- Strap style
Yukon Gear – Pinion Nut Washer (Part No.33166)
from
$23.99
Pinion nut washer for GM 12 bolt car & truck, 55-62 GM car & truck, GM 8.2″ & 63-79 Corvette.
Product Features:
See More
Product Features:
- Pinion nut washer for GM 12 bolt car and truck, 1955-1964 GM car and truck, GM 8.2″ and 1963-1979 Corvette.
Yukon Gear – U/Joint Strap Bolt For 14T, 7.5", And 8.5" GM (Part No.33351)
from
$8.49
U/joint strap bolt for 14T, 7.5″, and 8.5″ GM.
Product Features:
See More
Product Features:
- u-joint strap bolt for GM 10.5″ 14 bolt truck, 7.5″ and 8.5″
Yukon Gear – Positraction Cross Pin Bolt For GM 12 Bolt Car And Truck (Part No.33344)
from
$28.99
Positraction cross pin bolt for GM 12P and 12T.
Product Features:
See More
Product Features:
- Cross pin bolt for GM 12 bolt passenger car and truck
- For OEM positraction applications only
Yukon Gear – Posi Spring Kit For GM 7.5", With Preload Plates (Part No.33206)
from
$153.99
Product Features:
See More
- Positraction spring kit
- Fits GM 7.5″ and 7.625″ Dura Grip
- Includes preload plates
Yukon Gear – Clutch Guide For GM 7.5" & 7.6" Dura Grip (Part No.33251)
Yukon Gear – Dura Grip Case, GM 7.5 & 7.625", 3.23 & Up (Part No.20106)
from
$399.99
GM 7.5″ & 7.6″ DURA GRIP case, bare, 3.23 & up, 26spline & 28spline.
Product Features:
See More
Product Features:
- Dura Grip positraction carrier case
- Does not include spider gears
- Fits GM 7.5″ and 7.625″
- 3.23 and up ratios only
USA Standard Gear – Master Overhaul Kit for the 8.2" Buick, Olds, Pontiac Differential (Part No.37054)
from
$279.99
USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.
Product Features:
See More
Product Features:
- Fits 8.2″ Buick, Oldsmobile and Pontiac
- Uses Koyo bearings and races
- Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.
Driveworks – Oil Seal (Part No.S-3638)
Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-005.1)
from
$3.79
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dorman – Spindle Nut (Part No.K1002831647DOR)
from
$5.57
Spindle Nut
Yukon Gear – C/Clip (Part No.33083)
from
$8.99
C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.
Product Features:
See More
Product Features:
- c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
- .150″ thick
Motive Gear – Differential Gear Install Kit (Part No.GM7.5IK)
Richmond Gear – RngPnn (Part No.49-0045-1)
from
$350.99
RngPnn
USA Standard Gear – Axle Shaft For ’68-’72 Chevelle & ’70 Camaro (Part No.35058)
from
$162.99
USA Standard axle shaft for ’68-’72 Chevelle & ’70 Camaro. 12 bolt differential, 30 1/8″ long, 30 spline.
Product Features:
See More
Product Features:
- Fits 1968-1972 Chevelle and 1970 Camaro with 12 bolt differential
- 30 spline
- 30 1/8″ long
Yukon Gear – Bearing Race Driver (Part No.56016)
from
$188.99
Bearing race driver. No return.
Product Features:
See More
Product Features:
- Bearing race driver
- Fits HM89210 race
- All steel construction
Yukon Gear – Dana 25, 27, 30, 44, Model 20 And Model 35, GM 7.5", 8.2", 8.5", 12P, 12T, C9.25 Rear Cover Bolt (Part No.33286)
from
$9.99
5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.
Product Features:
See More
Product Features:
- Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
- 1/2″ head
Yukon Gear – Set Up Bearing (Part No.56045)
from
$153.99
M802048 set-up bearing (one bearing). No return.
Product Features:
See More
Product Features:
- Set up bearing
- Fits M802048 pinion bearing
- Easily slips on and off pinion journal to allow for easier pinion depth adjustment
Yukon Gear – Pinion Install Kit For GM 8.2" Differential For Buick, Pontiac, And Oldsmobile (Part No.13068)
from
$282.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits 8.2″ Buick, Oldsmobile and Pontiac
- Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.
Yukon Gear – Axle Seal For 5707 Or 1563 Bearing (Part No.30196)
from
$6.99
Axle seal for 5707 OR 1563 bearing.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Rear axle seal
- 2.250″ O.D.
Yukon Gear – Pinion Seal For GM 8.5", 8.2", Buick, Oldsmobile, And Pontiac (Part No.30017)
from
$9.99
Pinion seal for GM 8.5″, 8.2″, Buick, Oldsmobile, and Pontiac.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Pinion seal
- Fits GM 8.5″ rear, 8.2″ and 8.2″ in Buick, Oldsmobile and Pontiac
Yukon Gear – 8.2" & 8.5" Rear Cover Gasket (Part No.23020)
from
$10.99
8.2″ & 8.5″ rear cover gasket.
Product Features:
See More
Product Features:
- Cover gasket
- Fits GM 8.2″, 8.5″ and 8.6″
Pro-King – Differential Ring Gear Bolt (Part No.742G935)
from
$1.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Yukon Gear – Replacement Carrier Shim Kit For Dana 60, 70, 70HD, 70U & 80 (Part No.55011)
Yukon Gear – R1563Tav Rear Axle Bearing And Seal Kit (Part No.10004)
from
$42.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Includes axle bearing and seal
- Services one side
- Torrington Brand
- 2.250″ O.D.
- 1.400″ I.D.
Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)
from
$148.99
Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.
Product Features:
See More
Product Features:
- Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive
Dorman – Spindle Nut 3/4 In.-20 Hex Size 1-1/16 In. (Part No.615-065.1)
from
$6.99
This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Popular 1986 Pontiac Firebird Drivetrains Categories
1986 Pontiac Firebird Drivetrains
You count on your 1986 Pontiac Firebird to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 205 Drivetrains ranging in price from $1.99 to $1,014.99, you’re sure to find everything you need for your 1986 Pontiac Firebird.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 14 different brands like Moog, Driveworks, and National. 1986 Pontiac Firebird Drivetrains start as low as $1.99!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 4,532 extensive product reviews on 1986 Pontiac Firebird Drivetrains. Some of the top-rated Drivetrains products we carry are Oil Seal with 4.8 stars and Rear Differential Cover with 4.5 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1986 Pontiac Firebird below to get started!
Top-Rated Drivetrains Brands For Your 1986 Pontiac Firebird
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1986 Pontiac Firebird running right for years to come. In our inventory you’ll find brands like Moog, Driveworks, National, and even more.
Popular Felpro Drivetrains
You’ll find popular Felpro brand products across Differentials. All are waiting to get your 1986 Pontiac Firebird back on the road. Some of the top-rated Felpro products in these categories are:
Top-Rated MOOG Driveline Products Drivetrains
If MOOG Driveline Products are what you’re looking for, our inventory holds plenty. We stock MOOG Driveline Products brand Drivetrains for your 1986 Pontiac Firebird, and some of our most reviewed MOOG Driveline Products parts include:
FAQs for 1986 Pontiac Firebird Drivetrains
What are the most purchased Drivetrains for the 1986 Pontiac Firebird?
Out of 205 Drivetrains for the 1986 Pontiac Firebird, the most popular in our inventory are:
What are the top-rated 1986 Pontiac Firebird Drivetrains?
Top-rated Drivetrains for your 1986 Pontiac Firebird based on customer reviews/ratings are:
from
$20.99
(38)
Rear Differential Cover
“Looks great, face lift for the rear differential. Old one was rusted & in bad shape. Just remember to get the correct size.”
