1986 Mercury Grand Marquis Air Intakes
Find Your Specific 1986 Mercury Grand Marquis Air Intakes
Below you will find various in-demand Mercury Air Intakes, components and accessories for your 1986 Grand Marquis. Advance Auto Parts has popular Grand Marquis parts like Carburetor Kits, Throttle Bodies & Carb Parts, Carburetor Parts and more. You’ll also find aftermarket and OEM Air Intakes for other Grand Marquis model years including
2003,
2004,
2005,
2006,
2007,
2008,
2009,
2010,
2011 and more. Select a category of 1986 Mercury Grand Marquis Air Intakes below and start saving instantly.
Popular 1986 Mercury Grand Marquis Air Intakes Categories
Essential Air Intakes for 1986 Mercury Grand Marquis
Mr. Gasket – Intake Manifold Bolts (Part No.958G)
from
$22.99
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers
Product Features:
See More
Product Features:
- Hex Head
- Zinc Plated
- Ideal For Minimal Space
- 12-Point Head And Flange
- Zinc Plated For Protection
Delphi – Throttle Position Sensor (Part No.SS10387)
from
$45.99
Delphi’s ever growing portfolio of high quality vehicle sensors are backed by stringent OE development and product validation methods. We offer a wide range of sensors, including ABS, camshaft, crankshaft, knock, EGT, MAP, temperature, throttle position, and vehicle speed sensors for a variety of vehicle applications. All of our sensors are tested and calibrated to OE standards, ensuring accurate readings, which helps to reduce comebacks.
Product Features:
See More
Product Features:
- Delphi sensors are built to meet or exceed OE requirements and testing
- Not impacted by temperature changes and provide robust, long-lasting sensor protection
- Designed digital output for maximum signal to noise ratio
NTK – Throttle Position Sensor (Part No.TH0098)
from
$42.99
The Throttle Position Sensor (TPS) reports the angle of the throttle plate and thus the engine air intake to the ECM for optimal engine operation under all engine load conditions. Located on the throttle body, a failed Throttle Position Sensor may result in poor engine performance including stalling, hesitation, rough idle, increased fuel consumption, unnecessary stress on the emissions system and check engine light illumination.
Product Features:
See More
Product Features:
- OE MATCH: Throttle Position Sensors are manufactured to operational performance standards to meet or exceed OE fit, form and function to ensure proper feedback to the ECU to control engine performance.
- THE DIFFERENCE: Magnet size and strength optimized for precise output signal. 100% thermo-shock and vibration tested to ensure the best performance in extreme conditions.
Carquest Premium – Throttle Position Sensor (TPS) (Part No.ECA1468)
from
$47.99
The engine control module (ECM) requires multiple sensor inputs to perform the needed system operations. The Throttle Position Sensor (TPS) provides the computer the needed input for exact throttle plate position for ignition timing, injection pulse width, transmission shift control along with several other system operations. Carquest Premium throttle position sensors are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.
Product Features:
See More
Product Features:
- Designed to meet or exceed OE specifications for fit, form and function
- Manufactured with high quality materials, industry-leading electronic components and strict quality controls
- Superior sealing protecting sensor from moisture and temperature extremes
- Extensive design validation testing and 100% end-of-line tested
- Carquest Vehicle Solutions Technical Support available from ASE certified technicians: 1-866-687-5413
Edelbrock – Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors (Part No.12760)
from
$60.99
Product Features:
See More
- The Edelbrock #12760 4150 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4150 style Carburetor.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G2096)
from
$28.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1847)
from
$49.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Delphi – Fuel Injection Idle Air Control Valve (Part No.CV10140)
from
$78.99
Delphi is a Tier 1 supplier to the majority of global vehicle manufacturers and has been a manufacturer of dependable fuel pumps and fuel delivery parts for over 80 years. With over 30 OE-proprietary innovations and 150 patents in fuel technologies, Delphi is regarded as a market leader in North American fuel management with sales coverage at over 95%. Learn more about our expert-led training programs and tech hotline at 1-877-463-3574. Visit our Resource Center for helpful tips and tricks on fuel pumps, technologies, and more: https://www.delphiautoparts.com/usa/en-US/resource-center.
Product Features:
See More
Product Features:
- Delphi’s 100% OE replacement idle air control valves allow for accurate, stable, and precise air flow during the idle phase
- Provides superior fit resulting in an easier installations
- Maximizes fuel and engine efficiency
- Manufactured and engineered with premium quality and stringent standards eliminating potential for malfunctions
Delphi – Fuel Injection Idle Air Control Valve (Part No.CV10102)
from
$99.99
Delphi is a Tier 1 supplier to the majority of global vehicle manufacturers and has been a manufacturer of dependable fuel pumps and fuel delivery parts for over 80 years. With over 30 OE-proprietary innovations and 150 patents in fuel technologies, Delphi is regarded as a market leader in North American fuel management with sales coverage at over 95%. Learn more about our expert-led training programs and tech hotline at 1-877-463-3574. Visit our Resource Center for helpful tips and tricks on fuel pumps, technologies, and more: https://www.delphiautoparts.com/usa/en-US/resource-center.
Product Features:
See More
Product Features:
- Delphi’s 100% OE replacement idle air control valves allow for accurate, stable, and precise air flow during the idle phase
- Provides superior fit resulting in an easier installations
- Maximizes fuel and engine efficiency
Delphi – Fuel Injection Idle Air Control Valve (Part No.CV10125)
from
$77.99
Delphi is a Tier 1 supplier to the majority of global vehicle manufacturers and has been a manufacturer of dependable fuel pumps and fuel delivery parts for over 80 years. With over 30 OE-proprietary innovations and 150 patents in fuel technologies, Delphi is regarded as a market leader in North American fuel management with sales coverage at over 95%. Learn more about our expert-led training programs and tech hotline at 1-877-463-3574. Visit our Resource Center for helpful tips and tricks on fuel pumps, technologies, and more: https://www.delphiautoparts.com/usa/en-US/resource-center.
Product Features:
See More
Product Features:
- Delphi’s 100% OE replacement idle air control valves allow for accurate, stable, and precise air flow during the idle phase
- Provides superior fit resulting in an easier installations
- Maximizes fuel and engine efficiency
- Manufactured and engineered with premium quality and stringent standards eliminating potential for malfunctions
Edelbrock – Performer Intake Manifold Small-Block Ford (Part No.3721)
from
$414.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Edelbrock – Performer 289 Intake Manifold for Small-Block Ford, Black Finish (Part No.21213)
from
$465.99
Edelbrock part #21213 Performer 289 intake manifold is designed for street 260-289-302 c.i.d. Ford V8’s without EGR. Will not fit Boss 302 or 255 c.i.d. V8’s. Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket
Product Features:
See More
Product Features:
- Idle-5500 RPM Range
- Dual Plane Type-4150 Style Flange
- 3.5 in. Front Height, 4.12 in. Center Height, 4.75 in. Rear Height
- Black Powder Coated Finish
- Made In The USA
Idemitsu – Type TLS Automatic Transmission Fluid, 1 Quart (Part No.30040093-75000C)
from
$14.49
Formulated to meet the specific requirements of Toyota, Lexus, and Scion vehicles equipped with conventional (non-CVT) transmissions that require the use of ATF T-IV. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF T-IV is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.
Product Features:
See More
Product Features:
- Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
- Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
- Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
- Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
- Advanced anti-wear technology provides maximum protection to gears and bearings
- Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Edelbrock – Engine Intake Manifold Spacer #8728 For Manifold Part #2945, 3887 (Part No.8728)
from
$191.99Product Features:
- Fiber Laminate Spacers
- Provide Heat Insulation Between Upper and Lower
- Creates Cooler/Denser Charge
- Raise Intake 0.5in. For More Valve Cover Clearance
- Includes all Necessary Hardware for Installation
Felpro – Valley Pan Gasket Set (Part No.MS 96020)
from
$45.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- RIGHT TYPE – Valve stem seals designs are application-specific for the repair occasion using either deflector (umbrella) seals, O-ring style or positive seals
- QUALITY MATERIALS – Each valve stem seal features materials based on the specific application for your vehicle repair
- ENGINEERING EXPERTISE – Parts are reviewed, validated and approved by Fel-Pro engineers through rigorous research, development and testing
- INSTALLATION AID – Installation tool included to protect inner lip of seal from damage during seal installation
- COVERAGE – Available for domestic and foreign nameplate vehicles
Dorman – Upper Intake Manifold Gasket Set: 23 Piece Set (Part No.615-175GA)
from
$59.99
This engine intake manifold gasket set is designed to match the original gaskets required to reseal and restore proper function to the intake manifold on specified vehicles.
Product Features:
See More
Product Features:
- Direct replacement – this engine intake manifold gasket set is designed to match the original gaskets required to reseal and restore proper function to the intake manifold on specified vehicles
- Restores functionality – this gasket set is made to fit and fully restore part functionality after the original gasket fails
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Mr. Gasket – Intake Gasket (Part No.222)
from
$44.99
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Die-cut for an excellent fit
- Can be trimmed if necessary for modified port applications
- Complete with manifold end seals
- For OE replacement, high performance street, drag race and oval track use
Edelbrock – Intake replacement base and upper plenum gasket for #2945 & #3887 (Part No.7232)
Felpro – Fuel Injection Throttle Body Mounting Gasket (Part No.70261)
from
$3.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for the repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Holley – Professional Race Carburetor: 750 CFM, No Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80803BKX)
from
$1249.99
Xtreme Performance – Holley Ultra XP(TM) Circle Track Carburetors! Ultra XP carbs are 38% lighter than our original HP, have fuel capacity that is 20% greater and 30 other new features! They’re available in our Hard Core Gray(TM) hard coat anodized finish with Black(TM) billet for improved corrosion protection & also available in natural tumble-polished aluminum with Black(TM) metering blocks and base plate. The Aluminum Ultra XP Cirlce Tracks are available in 650 & 750 CFM’s. Holley Ultra XP carburetors are Specifically Calibrated for Circle Track & offer new features such as anti-siphon valve in the main body; high capacity HP bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, fully tunable billet metering blocks, billet base plate, wedge floats, adjustable secondary linkage and knurled (hand adjustable) curb idle screws. Holley Ultra XP carburetors are the ultimate in square bore race carburetors!
Product Features:
See More
Product Features:
- Aluminum Construction
- Saves 4.5 Pounds 38% Weight Savings
- Contoured Venturi Inlet Balances Airflow For Increased hp
- Air Bleeds Moved Outward For Smoother Transition Of Airflow
- Metering Blocks/True Gasket Sealing/Fully Adjustable
- Idle Bypass Valve Eliminates Holes In Throttle Plates
- Dual 30CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowls Provide 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Both Sides Of Bowls For Safe Fuel Level
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- 8AN O-Ringed Inlet Threads Offer A Variety Of Plumbing Options
- 4 Corner Idle Allows You To Precisely Control Your Idle System
Holley – Professional Race Carburetor: 1150 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Hard Core Gray (Part No.0-80906HB)
from
$1899.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Holley – Performance and Race Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Dual Inlet (Part No.0-4776C)
from
$799.99
The Ultra Double Pumper Carburetors feature all aluminum construction and are equipped with metering blocks and a base plate made from 6061-T6 billet aluminum. Three different anodized color options (Red, Blue, or Black) allow for a personalized look while maintaining the ultra high strength and durability you get from billet. They weigh in at approximately 5 lbs less than a comparable zinc carburetor. The new Ultra Double Pumper Carburetors have an enhanced fuel curve for optimum performance, with many more features such as aluminum construction; anodized billet aluminum metering blocks and base plate; 4 corner idle for precise idle control; mechanical secondaries for great performance; clear fuel level sight plugs for easy, no mess fuel level adjustments; Ford automatic transmission kickdown for use on popular Ford transmissions; four vacuum ports for all necessary vacuum accessories; and for the first time on a Double Pumper, factory pre-set electric choke for easy, fast cold start-ups. The clean, polished look coupled with Red, Blue, or Black metering blocks and throttle body will certainly set your ride apart whether you are at the show or track. Dont trust your performance to just anyone, Holley is the only Modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60s.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Optimized Street/Strip Calibration That Works Out Of The Box
- Man. Choke Cable Hand Controlled For Cold Start Control
- Mechanical Secondaries For Awesome Tire Turning Performance
- Dual Accelerator Pumps For Add Fuel Under Initial Acceleration
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
- Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing
- 100% Wet Flow Tested By Holley Technicians
United Carb – Remanufactured Carburetor 2 Barrel (Part No.7-7581)
from
$296.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-86670BK)
from
$899.99
The Ultra Street Avenger carburetors feature all aluminum construction and are equipped with metering blocks and a base plate made from 6061-T6 billet aluminum. They weigh in at approximately 5 lbs less than a comparable zinc carburetor. The new Ultra Street Avenger carburetors have the same great features as their aluminum counterparts such as a tumble polished aluminum finish; quick change vacuum secondaries for easy tuning to optimize performance or fuel economy; four vacuum ports for all necessary vacuum accessories; factory preset electric choke for easy startups; built-in fuel filters; and an included fuel line kit so there are no unnecessary trips back to the parts store. Ultra Street Avengers feature the same optimized street calibration as the zinc versions so you know they will run great on your vehicle. In addition, the Ultra Street Avenger now comes with anodized metering blocks and a base plate made from 6061-T6 billet aluminum and a built in, clear fuel level sight glass for easy, no mess fuel level adjustments. Don’t trust your performance to just anyone, Holley is the only Modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.
Product Features:
See More
Product Features:
- Ultra Street Avenger Has Optimized Calibration Works Out Of Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- 4 Corner Idle Allows You To Precisely Control Your Idle System
- Built In Clear Fuel Level Sight Glass For Fuel Level Adjustment
- Aluminum Construction For A 43% Weight Savings
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Street Carburetor: 450 CFM, No Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate (Part No.0-9776)
from
$599.99
Replace your old carburetor with original Holley performance 4160 carburetors. Budget-minded enthusiasts, like you, will be rewarded with maximum performance from your stock or mildly-modified engine. These Holley 4160 adjustable float carburetors are easier to tune than full race carburetors with temperamental secondary metering blocks and dual pumps. Plus, they’re available in your choice of universal or direct fit OE replacement versions with all emission provisions. Bolt-on installation and improved performance; no wonder when car guys think of carburetors, they think of Holley 4160 carburetors!
Product Features:
See More
Product Features:
- Universal Holley 4-Barrel Carburetor
United Carb – Remanufactured Carburetor 4 Barrel (Part No.7-7567)
from
$382.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Holley – Street Carbs (Part No.0-3310S)
from
$531.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Vibratory Polished Alum Good Looks/Weight Savings/Lasting Shine
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal Calibration For Easy Bolt-On Performance
- Man. Choke Cable Hand Controlled For Cold Start Control
- Vacuum Secondaries For Use On Wide Variety Of Vehicles
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
Holley – Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80458SA)
from
$516.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Vibrant Polished Alum Good Looks/Weight Savings/Lasting Shine
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal Calibration For Easy Bolt-On Performance
- Factory Preset Electric Choke For Easy Startups
- For All Weights/Gearing/Trans For Smooth Open Of Secondaries
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
- Power Valve Blow-Out Protection
- Clear Fuel Level Sight Glasses
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Upgrade your 1986 Mercury Grand Marquis with Top-Quality Air Intakes
When it comes to maintaining or upgrading your 1986 Mercury Grand Marquis, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Mercury or enhancing its overall performance, Air Intakes are key to keeping your Grand Marquis functioning at its best. At Advance Auto Parts, we offer a wide selection of 18 Air Intakes for the 1986 Mercury Grand Marquis, designed to meet your needs without breaking the bank.
From
Carburetor Kit
replacements to
Throttle Bodies & Carb Parts
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Air Intakes for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Air Intakes for your 1986 Mercury Grand Marquis at great prices.
Our Air Intakes inventory for this model
ranges from just $3.99 to $1,249.99, with
an average price of $252.14.
Our 18 Air Intakes in stock come from 6 trusted brands, so you’re sure to find the right part for your 1986 Mercury Grand Marquis without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1986 Mercury Grand Marquis, we stock popular OEM and aftermarket Air Intakes from top names
like FELPRO Holley, and more.
FELPRO Air Intakes
start at just $24.99 and boast an impressive 4.6 stars average rating from customers.
With 20 customer reviews and counting, our 1986 Mercury Grand Marquis Air Intakes have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Air Intake upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1986 Mercury Grand Marquis is always ready to roll. We’re committed to providing you with everything you need to keep your Grand Marquis in top shape, all in one place.
Start shopping confidently below for your 1986 Mercury Grand Marquis!
Best-Selling Carburetor Kits for 1986 Mercury Grand Marquis
Enhance the driving experience in your Mercury with 1 quality Carburetor Kit components, starting at $3.99.
Carquest Premium – Fuel Injector Seal Kit (Part No.AS009)
from
$3.99
CARQUEST fuel injector seal kits include the necessary O-rings and seals to properly reseal the injector, which is a recommended practice any time the injector is removed. Each kit services one injector and includes hard to find or previously dealer-only components.
Product Features:
See More
Product Features:
- Premium OE quality materials
- Services one injector
Most Popular 1986 Mercury Grand Marquis Throttle Bodies & Carb Parts
Customize your Mercury with 3 Throttle Bodies & Carb Parts products
like Throttle Position Sensors,
Throttle Body Mounting Gaskets, and
Throttle Bypass Valves, all
priced under $78.99.
Carquest Premium – Throttle Position Sensor with Hardware (Part No.ECC1065)
from
$49.99
Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.
Product Features:
See More
Product Features:
- Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
- 100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
- Designed to meet or exceed all OEM specifications in fit, form & function
- Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.
Delphi – Fuel Injection Idle Air Control Valve (Part No.CV10140)
from
$78.99
Delphi is a Tier 1 supplier to the majority of global vehicle manufacturers and has been a manufacturer of dependable fuel pumps and fuel delivery parts for over 80 years. With over 30 OE-proprietary innovations and 150 patents in fuel technologies, Delphi is regarded as a market leader in North American fuel management with sales coverage at over 95%. Learn more about our expert-led training programs and tech hotline at 1-877-463-3574. Visit our Resource Center for helpful tips and tricks on fuel pumps, technologies, and more: https://www.delphiautoparts.com/usa/en-US/resource-center.
Product Features:
See More
Product Features:
- Delphi’s 100% OE replacement idle air control valves allow for accurate, stable, and precise air flow during the idle phase
- Provides superior fit resulting in an easier installations
- Maximizes fuel and engine efficiency
- Manufactured and engineered with premium quality and stringent standards eliminating potential for malfunctions
Felpro – Fuel Injection Throttle Body Mounting Gasket (Part No.70261)
from
$3.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for the repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Top Picks for 1986 Mercury Grand Marquis Carburetor Parts
Upgrade Mercury Grand Marquis with top-quality Carburetor Parts parts, including 4 OEM and aftermarket selections for your 1986 model.
Holley – Street Carburetor: 500 CFM, Manual Choke, 2 Barrel, 2300 Bore, Single Inlet, Shiny (Part No.0-4412S)
from
$534.99
The 0-4412 is designed as a stock replacement for 2BBL street applications as well as being mandated for some oval track racing sanctioning bodies. Whether you are looking for a replacement carburetor to replace your tired and worn factory 2BBL or one to push you to the finish line on Saturday night, the Holley 0-4412 Performance 2BBL is the perfect choice.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
Holley – Street Carburetor: 500 CFM, Manual Choke, 2 Barrel, 2300 Bore, Single Inlet, Gold Dichromate (Part No.0-4412C)
from
$649.99
The 0-4412 is designed as a stock replacement for 2BBL street applications as well as being mandated for some oval track racing sanctioning bodies. Whether you are looking for a replacement carburetor to replace your tired and worn factory 2BBL or one to
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
- Does Not Work w/A.O.D. Transmissions
- Installation/Tuning DVD Incl.
Holley – Performance and Race Carburetor: 500 CFM, No Choke, 2 Barrel, 2300 Bore, Single Inlet (Part No.0-4412CT)
from
$649.99
Competition fuel curves provide safe and reliable horsepower for high performance race engines.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
Holley – Street Carburetor: 500 CFM, Electric Choke, 2 Barrel, 2300 Bore, Single Inlet, Shiny (Part No.0-80500)
from
$599.99
Street Avenger carburetors are known to bolt on right out of the box and Holley is excited to announce the addition of our new 2bbl Street Avenger models available in 350 and 500 CFM. Street Avenger carburetors have great features such as optimized street calibrations; three vacuum ports for all necessary vacuum accessories; factory preset electric choke for easy startups; built-in fuel filters; and an included 3/8″ fuel line connection so there are no unnecessary trips back to the parts store.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Built In No Trouble Fuel Inlet Filter
- Provides Precise Fuel Control For Low End Torque/Acceleration
- Gen Iv No Trouble Power Valve
- Three Vacuum Ports [1 Pcv/Brake 1 Timed Spark 1 Full]
- Limited Lifetime Warranty Defects In Material/Workmanship
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
In-Demand Intake Manifold Parts for 1986 Mercury Grand Marquis
Select from 10 premium Intake Manifold Parts parts for your 1986 Mercury Grand Marquis, with prices ranging from $22.99 to $1,249.99.
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 93334)
from
$24.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
Holley – SysteMAX; Intake Manifold Gasket (Part No.108-80)
from
$56.99
Kormetal gasket used between the SysteMax II Ford 5.0 liter upper and lower manifolds.
Product Features:
See More
Product Features:
- SysteMAX II Upper/Lower Manifold
Mr. Gasket – Intake Manifold Bolts (Part No.958G)
from
$22.99
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers
Product Features:
See More
Product Features:
- Hex Head
- Zinc Plated
- Ideal For Minimal Space
- 12-Point Head And Flange
- Zinc Plated For Protection
Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5835)
from
$43.99
Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Silicone beading on both sides of each gasket
- Complete with manifold end seals and distributor gasket
- For OE replacement, high performance street, drag race and oval track use
- Creates Tight Leak proof Seal
Edelbrock – Intake replacement base and upper plenum gasket for #2945 & #3887 (Part No.7232)
Holley – Intake Manifold (Part No.300-72S)
from
$1249.99
Holley products have been the undisputed leader in fuel systems for over 100 years. Holley carburetors power every NASCAR Sprint Cup team and every NHRA Pro-Stock champion. Holley’s products include performance fuel pumps, fuel injection, intake manifolds, cylinder heads & engine dress-up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies, Hooker Headers, Flowtech Headers, NOS, Weiand, or Earl’s, Holley products can give you the edge you need over the competition.
Product Features:
See More
Product Features:
- Retains Stock Injector
- Retains Water Outlet Locations
- Internal Erg Passage
- External EGR Passage
- Maximized Port and Runner Sizes
- Maximum Unrestricted Air Flow
- 50 State Legal
Holley – Manifold; Ford II Lower (Part No.300-75S)
from
$724.99
Utilizes late model alternator and A/C bracket mounting provisions. Has vacuum taps off Manifold runners. Uses cable bracket P/N 20-101 for GM 700R4 transmission. Extra installation hardware included.
Product Features:
See More
Product Features:
- Dual Plane Design
- Front Height 3.5 in.
- Rear Height 4.18 in.
Edelbrock – Performer Intake Manifold Small-Block Ford (Part No.3721)
from
$414.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Edelbrock – Engine Intake Manifold Spacer #8728 For Manifold Part #2945, 3887 (Part No.8728)
from
$191.99Product Features:
- Fiber Laminate Spacers
- Provide Heat Insulation Between Upper and Lower
- Creates Cooler/Denser Charge
- Raise Intake 0.5in. For More Valve Cover Clearance
- Includes all Necessary Hardware for Installation
Edelbrock – Intake Manifold replacement base and upper plenum gasket for #7126 (Part No.7231)
from
$26.99Product Features:
- Performer RPM 5.0L Gasket Set
- Includes Base To-Upper And Plenum Cover Gaskets
Top-Rated Air Intakes Brands For Your 1986 Mercury Grand Marquis
Shop for the best-rated brands offering Air Intakes and other products for your 1986 Mercury Grand Marquis. Below you’ll find some of our best rated Air Intakes from FELPRO and Holley, and more. Air Intakes from these brands that fit a 1986 Grand Marquis start at just $24.99 and are rated as high as 4.6 stars. OEM and aftermarket Air Intakes don’t get more top quality, durable, and affordable than from the brands below.
Popular FELPRO 1986 Mercury Grand Marquis Air Intakes
When it comes to maintaining or upgrading your 1986 Mercury Grand Marquis, using quality Air Intakes is essential to ensure durability and a perfect fit. FELPRO ticks all of those boxes. We offer a wide selection of FELPRO Air Intakes, specifically designed for the 1986 Mercury Grand Marquis. With over 1 FELPRO brand Air Intakes in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $24.99. Plus, with over 8 customer reviews and an average rating of 4.6 stars, you can trust that our FELPRO Air Intakes will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
from
$24.99
(8)
Engine Intake Manifold Gasket Set
“Similar to high-end racing type intake gaskets at a much lower price. Silicone rubber with steel core. End pieces are molded silicone rubber instead”
Popular Holley 1986 Mercury Grand Marquis Air Intakes
Holley auto parts is one of the highest quality Air Intake brands in the market. Any 1986 Mercury Grand Marquis owner should feel confident when installing genuine Holley parts in their vehicle. To ensure the best fit and performance for your 1986 Grand Marquis, Advance Auto Parts carries a full inventory of 1 Holley Air Intakes. Plus you will be keeping your Mercury in peak condition while saving money because prices on these Holley Air Intakes range up to $56.99, plus, with more than 1 customer reviews and an impressive 4.1 stars average rating, you can be confident the Fram Air Intakes below will deliver on both quality and value.
from
$56.99
(1)
SysteMAX; Intake Manifold Gasket
“Gaskets went on easy. Have not ran the engine yet, but hopefully Felpro’s quality will allow these to last a good long time!”
FAQs for 1986 Mercury Grand Marquis Air Intakes
Which Air Intakes are best-sellers for 1986 Mercury Grand Marquis?
Out of 18 Air Intakes that fit 1986 Mercury Grand Marquis, the following parts are the top sellers:
- Fuel Injector Seal Kit (11450096) – $3.99
- Throttle Position Sensor with Hardware (12424366) – $49.99
- Intake Manifold Bolts (17360287) – $22.99
What’s the price range for 1986 Mercury Grand Marquis Air Intakes?
Air Intake prices for the 1986 Mercury Grand Marquis start at $3.99 and go up to $1,249.99 for the most premium parts.
What’s the average price of a Air Intake for a 1986 Mercury Grand Marquis?
The average price for Air Intakes for the 1986 Mercury Grand Marquis is $252.14. Keep in mind the variety of part types within our Air Intake category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Air Intakes for other Mercury Grand Marquis model years?
What are the cheapest Air Intakes for my 1986 Mercury Grand Marquis?
The cheapest 1986 Mercury Grand Marquis Air Intakes we carry in stock are:
- Fuel Injector Seal Kit (11450096) – $3.99
- Fuel Injection Throttle Body Mounting Gasket (3210006) – $3.99
- Intake Manifold Bolts (17360287) – $22.99
- Intake replacement base and upper plenum gasket for #2945 & #3887 (22342065) – $22.99
- Engine Intake Manifold Gasket Set (5781639) – $24.99
What are the top-rated Air Intakes that fit the 1986 Mercury Grand Marquis?
Out of 20 reviews by customers, our 1986 Mercury Grand Marquis Air Intakes have an average customer rating of . These are some of the highest-rated Air Intake types for the 1986 Mercury Grand Marquis and their top-rated products:
- Intake Manifold Parts
- SysteMAX; Intake Manifold Gasket (17120507) – $56.99
- Engine Intake Manifold Gasket Set (5781639) – $24.99
- Intake Manifold Bolts (17360287) – $22.99
What types of Air Intakes do you sell for my 1986 Mercury Grand Marquis?
As of 11/2/25, these are some of the most in-demand types of Air Intakes for a 1986 Mercury Grand Marquis:
Can I get help with 1986 Mercury Grand Marquis Air Intake orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Mercury Air Intakes and more.
What is your return policy for Mercury Grand Marquis Air Intakes?
Advance Auto Parts keeps returns simple. For new Mercury Grand Marquis Air Intakes and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
