1986 Jeep Scrambler Differentials

Yukon replacement trail repair kit for Dana 30 and 44 with 1350 size U/joint and straps. This kit comes with a yoke, U/joint, pinion seal, U/bolt or strap kit, pinion nut, and pinion nut washer (if applicable).

Product Features:

• Fits Dana Spicer 30 and 44
• 1350 u-joint size
• Kit includes yoke, U-joint, pinion seal, pinion nut and washer, straps, bolts and threadlocker

Yukon Gear & Axle tools are made to the highest industry standard.

Product Features:

• Works on popular Ford, GM, Chrysler, and many other housings
• For differentials with XHD Clamshells
• Can accommodate up to one-ton applications
• Comes with a handy bench-top stand
• This top-quality differential tool is built to last

Model 20 gasket.

Product Features:

• Cover gasket
• Fits AMC Model 20

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits AMC Model 20
• Works with Spartan Locker or standard open spider gears

Yukon Gear & Axle clutch kits fit popular GM and Chrysler diffs outfitted with a Power Lok positraction unit feature 14 advanced carbon clutch plates, ensuring total traction and long-lasting performance.

Product Features:

• Clutch kit
• Fits Chrysler 8.75″, 1955-1964 GM passenger car and AMC Model 20 Power Lok positraction

Redline Heavy Shockproof Gear Oil is formulated to provide lasting protection.

Product Features:

• Includes four quarts of Redline Shockproof oil

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Easily slips on and off pinion journal to allow for easier pinion depth adjustment
• Fits M802048 pinion bearing
• For popular GM, Ford, Dana, and Chrysler differentials

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Roll pin for Dana Spicer 30 and Dana Spicer 44
• 0.235″ diameter

Yukon shim kits are precision machined and tailored for each individual application to ensure you have the right shims for every set up.

Product Features:

• Complete shim kit for Dana Spicer 44

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion gear thrust washer for Dana Spicer 44, GM 8.2″ and 1955-1964 GM passenger car

Yukon Full Spools are a cost-effective way to convert a diff to 100% lockup. Installation is easy as they install in place of your differential carrier assembly. Each Yukon spool is made from high-quality 8620 steel and heat treated for additional strength. A spool is an outstanding choice for dedicated off-road and drag racing vehicles only.

Product Features:

• Fits Chrysler Dana Spicer 44 with 30 spline axles
• 3.73 and down ratio only
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
• 0.030″ thick

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

• Inner oil slinger for Dana Spicer 25, 27, 30, 44 and 50

Differential

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

• Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
• 1/2″ head

Yukon right hand axle for ’10-’14 Ford F150 SVT Raptor front, 31 spline.

Product Features:

• Bulkhead quit connect fitting

Yukon Gear & Axle offers an extensive line of general replacement and high-performance axles for passenger car, truck and SUV applications. High quality alloys and the latest in heat-treating technologies provide a stronger-than-stock axle for off-road, on the street, or at the track.

Product Features:

• 29 spline
• 28 5/8″ long
• Fits AMC Model 20 in 1982-1986 CJ7
• Two piece axle
• Left hand side
• Does not include hub

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Dana Spicer 44 rear
• Uses Koyo bearings and races
• 30 spline
• Rear axle kit
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers, thread locker, marking compound with brush and gasket.

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver select ability.

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 44 and Toyota 8″ and V6

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

• Fits standard rotation Dana Spicer 44
• 8.50″ ring gear diameter
• 26 spline pinion
• 10 ring gear bolts
• 3.54 ratio

Crown Automotive offers the largest line of replacement parts for Jeep (R), as well as a growing line of parts for Chrysler and Dodge vehicles. Our applications features Axle, Body, Brake, Clutch, Cooling, Electrical, Engine, Fuel, Lamps, Mirrors, Steering, Suspension, Transmission and Wiper.

Product Features:

• Long-Lasting, Durable Crown Automotive Products
• Hazardous Free Material
• Offers OE Fit And Function
• Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
• 0.480″ tall

Yukon replacement standard open carrier case for Dana 30, 3.73 & up, 1.943″ tall. If purchasing this case for a D30 JK front, you will need to also purchase spider gear set YPKD30-S-27.

Product Features:

• Standard open carrier case
• Fits Dana Spicer 30
• 3.73 and up ratio only
• Does not include spider gears

Yukon Gear & Axle spider gear kits feature higher quality materials and better manufacturing techniques than OEM to ensure a longer lasting spider gear set. Kit delivers everything needed for a complete and proper spider gear set replacement.

Product Features:

• Spider gear kit
• Fit Dana Spicer 44 open differential with 30 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Yukon shim kits are precision machined and tailored for each individual application to ensure you have the right shims for every set up.

Product Features:

• Complete shim kit for Dana Spicer 30 front

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Power Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

Yukon 1541H alloy 6 lug right hand rear axle for ’97 to ’04 Chrysler 9.25″ Durango with a length of 30-1/2 inches and 31 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

• Cover gasket
• Fits Dana Spicer 30