1986 Chrysler Fifth Avenue Differentials

Essential 1986 Chrysler Fifth Avenue Differentials

Yukon Gear – Standard Open Spider Gear Kit For 7.25" Chrysler With 25 Spline Axles (Part No.16001)

Standard Open Spider Gear Kit For 7.25" Chrysler With 25 Spline Axles

from

$234.99
Yukon standard open spider gear kit for 7.25″ Chrysler with 25 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:
  • Spider gear kit
  • Fits Chrysler 7.25″ rear with open differential
  • Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
See More

Yukon Gear – Carrier Installation Kit For ’76 & Up Chrysler 8.25" Rear (Part No.57014)

Carrier Installation Kit For '76 & Up Chrysler 8.25" Rear

from

$78.99
Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for ’76 & up Chrysler 8.25″ rear.

Product Features:
  • Fits 1976 and up Chrysler 8.25″
  • Includes carrier bearings and races
See More

Yukon Gear – Pinion Install Kit For Chrysler 7.25" Differential (Part No.13001)

Pinion Install Kit For Chrysler 7.25" Differential

from

$223.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:
  • Fits Chrysler 7.25″
  • Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.
See More

Yukon Gear – Rubber Fill Plug For Chrysler (Part No.33463)

Rubber Fill Plug For Chrysler

from

$22.99
Product Features:
  • Rubber fill plug
  • Fits Chrysler 7.25″, 8.25″ and 9.25″
See More

National – Bearings (Part No.M86610)

Bearings

from

$9.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Yukon Gear – Pinion Nut (Part No.33142)

Pinion Nut

from

$10.99
Pinion nut for Chrysler 7.25″, 8.0″ IFS, 8.25″, 8.75″ fine spline, 9.25″ front & rear, 7/16″ x 14.

Product Features:
  • Pinion nut for Chrysler 8.0″ IFS, 8.25″, 8.75″ with 29 spline pinion and 9.25″ rear
  • 7/8″ x 14 thread
See More

Pro-King – Differential Internal Nest Kit (Part No.722B717)

Differential Internal Nest Kit

from

$194.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:
  • All products are designed to meet or exceed OE quality, form, fit and funtion.
See More

Powertrax – Lock Right Locker (Part No.1230-LR)

Lock Right Locker

from

$450.99
The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
  • Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
  • Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
  • Powertrax® = Extreme Traction Systems!
  • See More

    USA Standard Gear – Spartan Locker For Chrysler 8.25" With 27 Spline Axles, Includes Heavy-Duty Cross Pin Shaft (Part No.17037)

    Spartan Locker For Chrysler 8.25" With 27 Spline Axles, Includes Heavy-Duty Cross Pin Shaft

    from

    $829.99
    The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

    Product Features:
    • Fits Chrysler 8.25″ with 27 spline axles
    • Made from 9310 steel for added strength
    • Replaces the spiders in a standard carrier case
    See More

    Felpro – DIFFERENTIAL GASKET (Part No.RDS 55047)

    DIFFERENTIAL GASKET

    from

    $6.79
    Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

    Product Features:
    • Meets or exceeds all original equipment specifications
    • Application specific design to ensure a perfect fit
    • Unsurpassed quality you can trust
    • Validated for fit, form and function
    • Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
    See More

    Yukon Gear – High Performance Ring & Pinion Gear Set For Chrysler 8.25" In A 3.90 Ratio (Part No.24003)

    High Performance Ring & Pinion Gear Set For Chrysler 8.25" In A 3.90 Ratio

    from

    $459.99
    Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

    Product Features:
    • Fits Chrysler 8.25″
    • 8.25″ ring gear diameter
    • 27 spline pinion
    • 10 ring gear bolts
    • 3.90 ratio
    See More

    Motive Gear – Differential Crush Sleeve (Part No.3507575)

    Differential Crush Sleeve

    from

    $2.49


    Product Features:
    • CRUSH SLEEVE 7.25 & 8.25 MIN ORDER 5000
    See More

    USA Standard Gear – Chrysler 8.25" Spartan Locker Cross Pin Shaft (Part No.17035)

    Chrysler 8.25" Spartan Locker Cross Pin Shaft

    from

    $49.99
    Product Features:
    • USA Standard Gear heavy-duty cross pin shaft
    • Fits Chrylser 8.25″ with 27 and 29 spline axles
    • Works with Spartan Locker or standard open spider gears
    See More

    Yukon Gear – 7.25" & 8.25" Chrysler Pinion Seal (Part No.30189)

    7.25" & 8.25" Chrysler Pinion Seal

    from

    $16.99
    7.25″ & 8.25″ Chrysler pinion seal.Yukon Mighty seal.

    Product Features:
    • Pinion seal
    • Fits Chrysler 7.25″ and 8.25″
    See More

    Motive Gear – Differential Carrier Gear Kit (Part No.C7.25BI)

    Differential Carrier Gear Kit

    from

    $108.99


    Product Features:
    • CHRYSLER 7.25″ INTERNAL KIT
    See More

    Valvoline – High Performance Transmission & Differential Gear Oil: Conventional 80W-90, 1 Gallon (Part No.773732)

    High Performance Transmission & Differential Gear Oil: Conventional 80W-90, 1 Gallon

    from

    $32.99
    Valvoline High Performance Synthetic Gear Oil is the thermally stabile extreme pressure lubricant that offers outstanding protection for gearboxes and differentials in passenger cars, light trucks, and sport utility vehicles. Combined with high quality synthetic base oils, our formula’s superior additives help reliably safeguard against severe temperatures, shock loads, foaming, scuffing, scouring, corrosion and pitting in high load, high torque and high horsepower conditions. Can be used in conventional and limited slip hypoid differentials where GL-5 is specified as well as non-synchronized manual transmissions that require GL-4. Protect your gears with Valvoline, the #1 gear oil brand.

    Product Features:
    • HIGH PERFORMANCE EXTREME-PRESSURE ADDITIVES HELP MINIMIZE WEAR in high pressure and high temperature conditions
    • EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION can easily handle both winter and summer conditions for dependable coverage and protection year-round
    • REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
    • FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
    • SUPERIOR ADDITIVES help reliably safeguard against severe temperatures, shock loads, foaming, scuffing, scouring, corrosion and pitting in high load, high torque and high horsepower conditions
    See More

    Pro-King – Differential Axle Bearing (Part No.742G280)

    Differential Axle Bearing

    from

    $16.79
    Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

    Product Features:
    • All products are designed to meet or exceed OE quality, form, fit and funtion.
    See More

    Yukon Gear – Yoke For Chrysler 7.25" And 8.25" With A 7290 U/Joint Size (Part No.41005)

    Yoke For Chrysler 7.25" And 8.25" With A 7290 U/Joint Size

    from

    $359.99
    Yukon yoke for Chrysler 7.25″ and 8.25″ with a 7290 U/joint size. 2.625″ snap ring span. 1.125″ cap diameter. Inside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

    Product Features:
    • Fits Chrysler 7.25″ and 8.25″
    • 27 spline
    • 7290 u-joint size
    • Inside snap ring design
    • 2.625″ snap ring span
    • 1.125″ cap diameter
    • Strap style
    See More

    Yukon Gear – Cross Pin Bolt (Part No.33067)

    Cross Pin Bolt

    from

    $6.99
    Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

    Product Features:
    • Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS
    See More

    Yukon Gear – Standard Open Carrier Case For Chrysler 8.25", 29 Spline, 2.56 & Up, 1997 & Up Only (Part No.20011)

    Standard Open Carrier Case For Chrysler 8.25", 29 Spline, 2.56 & Up, 1997 & Up Only

    from

    $634.99
    Product Features:
    • Standard open carrier case
    • Does not include spider gears
    • Fits Chrysler 8.25″
    • 29 spline only
    • ABS and non-ABS compatible
    See More

    Yukon Gear – Bearing Race Driver Set, 21 Piece (Part No.56030)

    Bearing Race Driver Set, 21 Piece

    from

    $1566.99
    21 Piece bearing race driver set. (Box wt: 140lbs) No return.

    Product Features:
    • Bearing race driver set
    • 21 pieces
    • All steel construction
    See More

    Yukon Gear – Pinion Gear And Thrust Washer For 8" And 9" Ford, Model 20, And 7.25" Chrysler (Part No.33301)

    Pinion Gear And Thrust Washer For 8" And 9" Ford, Model 20, And 7.25" Chrysler

    from

    $4.99
    Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

    Product Features:
    • Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″
    See More

    Yukon Gear – 8.25" Chrysler Cover Gasket (Part No.23000)

    8.25" Chrysler Cover Gasket

    from

    $12.99
    8.25″ Chrysler cover gasket.

    Product Features:
    • Cover gasket
    • Fits Chrysler 8.25″
    See More

    Yukon Gear – The Carrier Bearing Puller (Part No.56034)

    The Carrier Bearing Puller

    from

    $689.99
    The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

    Product Features:
    • Carrier bearing puller
    • Works with an impact gun to safely and easliy remove carrrier bearings
    • Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications
    See More

    Driveworks – Tapered Cone/Cup Wheel Bearing Set (Part No.S-A-35)

    Tapered Cone/Cup Wheel Bearing Set

    from

    $13.99
    Value-priced bearing meets all cataloged application requirements.

    Product Features:
    • Brand may vary by location
    See More

    Yukon Gear – Steel Cover For Chrysler 8.25" (Part No.32312)

    Steel Cover For Chrysler 8.25"

    from

    $159.99
    Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

    Product Features:
    • Fits Chrysler 8.25″
    • Steel
    See More

    Yukon Gear – Replacement Pinion Depth Shims For Dana 35, Model 35 & Chrysler 7.25" (Part No.55014)

    Replacement Pinion Depth Shims For Dana 35, Model 35 & Chrysler 7.25"

    from

    $17.99
    Yukon 1541H alloy right hand rear axle for Model 35 (drum brakes) with a 54 tooth, 2.7″ ABS ring. axle has a length of 29-1/4″ inches and 27 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H allo

    Product Features:
    • Pinion depth shims for AMC Model 35 and Chrysler 7.25″
    See More

    Yukon Gear – Ring Gear Bolt For Chrysler 7.25", 8" IFS, 8.25", 8.75" & GM 7.2" IFS Front (Part No.33035)

    Ring Gear Bolt For Chrysler 7.25", 8" IFS, 8.25", 8.75" & GM 7.2" IFS Front

    from

    $8.99
    Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

    Product Features:
    • Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
    • 3/8″ x 24 thread
    • .866″ long
    See More

    1986 Chrysler Fifth Avenue Differentials

    Maybe you’re in the middle of a full rebuild of that 1986 Chrysler Fifth Avenue. Maybe you just need a couple of Differentials. Either way, Advance Auto Parts has 118 different Differentials in our inventory ranging from $2.49 to $1,566.99. That means you can find the exact parts or products you need to keep that 1986 Chrysler Fifth Avenue running smoothly.

    Differentials are only as good as their brand. We stock 12 different brands to make sure you have plenty of trusted parts to choose from for your 1986 Chrysler Fifth Avenue. Driveworks, Dorman, and National are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

    We know you’ll find the perfect Differentials for your 1986 Chrysler Fifth Avenue, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 70 reviews in this category, some of the top rated parts include Differential Pinion Shim Kit with 5.0 stars and Differential Crush Sleeve with 5.0 stars.

    So if you’re in the market for aftermarket Differentials to keep your 1986 Chrysler Fifth Avenue rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

    Differentials Brands To Make Your 1986 Chrysler Fifth Avenue Last

    Simple repair, complete replacement, or a full rebuild. No matter the job, your 1986 Chrysler Fifth Avenue demands trusted brand parts and products to keep it running. Many trusted brands of Differentials make up Advance Auto Parts’ inventory, and all are ready to help make your Fifth Avenue the best it can be. Be sure to browse some of our top Differentials brands and parts.

    Popular Driveworks Differentials

    We carry Driveworks parts in our stock across Front Differential Pinion Bearings categories, plus more. For a 1986 Chrysler Fifth Avenue, our most popular Driveworks Differentials include:
    Tapered Cone/Cup Wheel Bearing Set
    from $13.99
    (14)
    Tapered Cone/Cup Wheel Bearing Set
    Front Differential Pinion Bearings

    FAQs for 1986 Chrysler Fifth Avenue Differentials

    What are the most purchased Differentials for the 1986 Chrysler Fifth Avenue?

    Out of 118 Differentials for the 1986 Chrysler Fifth Avenue, the most popular in our inventory are:
    DIFFERENTIAL GASKET
    from $6.79
    (21)
    DIFFERENTIAL GASKET
    Rear Housing Cover Gaskets
    3 Qt - 80W90 Conventional Gear Oil With Posi Additive
    from $57.99
    This product is not rated
    3 Qt – 80W90 Conventional Gear Oil With Posi Additive
    Differential Oil
    Bearings
    from $23.99
    (7)
    Bearings
    Front Differential Pinion Bearings

    What are the top-rated 1986 Chrysler Fifth Avenue Differentials?

    Top-rated Differentials for your 1986 Chrysler Fifth Avenue based on customer reviews/ratings are:
    Differential Pinion Shim Kit
    from $7.49
    (1)
    Differential Pinion Shim Kit
    “good product”
    Differential Crush Sleeve
    from $2.49
    (1)
    Differential Crush Sleeve
    “High quality, would buy again”
    Differential Carrier Gear Kit
    from $108.99
    (1)
    Differential Carrier Gear Kit
    “easy installation, excellent fit,and seems to be made of good quality materials.”