1986 Chevrolet Camaro Air Intakes
More 1986 Chevrolet Camaro Air Intakes Categories
If you’re looking for an original Air Intakes replacement for a 1986 Chevrolet Camaro, you can search through our selection below. You’ll also find aftermarket and OEM Air Intakes to meet your needs.
Essential 1986 Chevrolet Camaro Air Intakes
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$12.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$40.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1779)
from
$38.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Carquest – Choke Thermostat (Part No.779-1527)
from
$47.99
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1040)
from
$18.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Felpro – Carburetor Mounting Gasket (Part No.60731)
from
$7.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Dorman – GM Bumper Retainer (Part No.961-364D)
from
$4.49
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.
Product Features:
See More
Product Features:
- Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
- Quality material – this retainer is made of durable material for long-lasting service
- Versatile design – this retainer is suitable for a variety of automotive uses
- Excellent value – this part offers original equipment quality at a competitive cost
Dorman – Electrical Harness – 3-Wire Throttle Position Sensor (Part No.85186)
from
$16.29
This throttle position sensor connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this throttle position sensor connector matches the appearance and function of the factory hardware on specified applications
- Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
AutoLine Products – Throttle Body Unit (Part No.FI917)
from
$423.39
All of our throttle bodies come with fuel injectors, idle air control valve, pressure regulator, and throttle postion sensor
Product Features:
See More
Product Features:
- All castings are completely disassembled and thoroughly cleaned using industrial compounds and equipment.
- Housings are surface restored and repaired as necessary. Base sealing faces are surface machined.
- All components that do not meet Autoline’s rigid standards are replaced with parts which equal or exceeed O.E.M. specifications.
- Housings are vacuum calibration verified to meet OE specifications. Tests include throttle stop setting, vacuum drop test and vacuum port verification.
GM Genuine Parts – Fuel Injection Throttle Body Mounting Gasket (Part No.12634371)
from
$11.99
GM Genuine Parts Fuel Injection Throttle Body Mounting Gaskets are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These gaskets help provide an air-tight seal between the throttle body and the intake manifold, and are GM-recommended replacements for your vehicle’s original components. Replace this gasket whenever you service the throttle body, as leaks can negatively affect the air/fuel ratio and compromise performance. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Helps prevent excess air form entering the intake
- Helps seal the intake and throttle from the elements
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Holley – Carburetor – 770 CFM Alum Street Avenger E/C (Part No.0-83770)
from
$626.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Features A Tumble Polished Finish Can Also Be Hand Polished
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Glass Fuel Level Sight Windows For Easy Safe Float Adjustments
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- 4 Corner Idle Allows You To Precisely Control Your Idle System
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)
from
$186.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent
Product Features:
See More
Product Features:
- Steel Material
- Zinc Plated
- Adjustable
- 3-Barrel Configuration
- Made In The USA
Dorman – Breather Element Clips – GM 2002-76-Use with breather elements: AC; FB59: Fram; CA19: Purolator; AF9 (Part No.41251)
from
$1.99
Breather Element Clips – GM 2002-76-Use with breather elements: AC; FB59: Fram; CA19: Purolator; AF9
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$62.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$20.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", 12 Point Head Type, Polished, With Washers (Part No.434-2101)
from
$46.49
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
ACDelco – GM Original Equipment Throttle Position Sensor (Part No.C7012488075ACD)
from
$184.77
The ACDelco GM Original Equipment Throttle Position Sensor is a GM-recommended replacement for your vehicle’s original component. The TPS reports the throttle position to the engine control module, which uses the signal to adjust fuel delivery and ignition timing. This throttle position sensor kit meets the performance standards you would expect from General Motors.
Product Features:
See More
Product Features:
- Undergo the same stringent testing process as the original part
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Edelbrock – Intake Manifold replacement runner to base gaskets (Part No.6942)
from
$14.99Product Features:
- Replacement Gasket For PN[3789] Edelbrock Intake
- One Gasket Only
- Goes Between Base pn[3785] And Top PN[3789]
- Also Included in Base PN[3789]
Felpro – Carburetor Mounting Gasket (Part No.60110)
from
$4.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Carquest Premium – Air Charge Temperature Sensor (Part No.WTA1042)
from
$25.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$13.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Dorman – Body Bolt With Washer – M6-1.0 X 25mm (sold by each) (Part No.700-251)
from
$1.29
These nuts are manufactured using durable materials and corrosion tested to ensure required strength and longevity.
Product Features:
See More
Product Features:
- Durable materials – manufactured to specific thread tolerance standards
- Corrosion tested – hardware undergoes salt spray testing to ensure corrosion resistance
- Multipurpose usefulness – can be used in a variety of applications, from auto to home
- Trustworthy quality – backed by team of professional engineers and quality control specialists in the United States
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$24.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Dorman – Help – Throttle Return Spring (Part No.59209)
from
$9.99
This throttle return spring is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this throttle return spring matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this spring is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)
from
$12.99
The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var
Product Features:
See More
Product Features:
- Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
- Includes Gasket
- 1/2 in. x 28 Power Valve Thread
- For Applications That Prefer To Run Carbs Without The Power Valves
- Made In The USA
Edelbrock – Pro-Flo 1000 Series Chrome Air Cleaner with Foam Element with 5-1/8" Air Horn (Part No.1002)
from
$31.99Product Features:
- Super Flow; Good Filtration
- Urethane Foam Element
- Strong Metal Inner Frame
- Performance Benefits
- Cleans With Soap and Water
- Low Maintenance Cost
- Simple To Install
- Nicely Finished; Low Profile
Edelbrock – Triple Carburetor Fuel Log Kit #1288 with 5-1/2 in. Outlet Spacing (Part No.1288)
from
$99.99
This Edelbrock Fuel Log kit #1284 is an exact replica of the original design used by Vic Sr. in the 1950’s. They are made from extruded aluminum tube with a 3/8″ threaded outlet at each end and a polished finish. Kit includes, black neoprene hose, Corbin
Product Features:
See More
Product Features:
- Polished Log
- Brass Fittings
- Black Neoprene Hose
- 5-1/2 in. Outlet Spacing
- Includes Hose Clamps
Felpro – Air Cleaner Mounting Gasket (Part No.5292)
from
$3.29
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Popular 1986 Chevrolet Camaro Air Intakes Categories
1986 Chevrolet Camaro Air Intakes
You count on your 1986 Chevrolet Camaro to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Air Intakes. With 101 Air Intakes ranging in price from $1.29 to $1,776.99, you’re sure to find everything you need for your 1986 Chevrolet Camaro.
Brands matter. If you want to shop a specific Air Intakes brand, we stock 15 different brands like Felpro, Carquest Premium, and Dorman. 1986 Chevrolet Camaro Air Intakes start as low as $1.29!
One of the best ways to find top quality OEM or aftermarket Air Intakes is by asking professionals. Short of that, you can shop with confidence thanks to our 423 extensive product reviews on 1986 Chevrolet Camaro Air Intakes. Some of the top-rated Air Intakes products we carry are Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg with 4.5 stars and Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) with 4.6 stars.
Did we mention you can order your Air Intakes from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Air Intakes inventory for your 1986 Chevrolet Camaro below to get started!
Top-Rated Air Intakes Brands For Your 1986 Chevrolet Camaro
Trusted Air Intakes OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1986 Chevrolet Camaro running right for years to come. In our inventory you’ll find brands like Felpro, Carquest Premium, Dorman, and even more.
Popular Holley Air Intakes
You’ll find popular Holley brand products across Intake Manifold Parts. All are waiting to get your 1986 Chevrolet Camaro back on the road. Some of the top-rated Holley products in these categories are:
Top-Rated Felpro Air Intakes
If Felpro are what you’re looking for, our inventory holds plenty. We stock Felpro brand Air Intakes for your 1986 Chevrolet Camaro, and some of our most reviewed Felpro parts include:
FAQs for 1986 Chevrolet Camaro Air Intakes
What are the most purchased Air Intakes for the 1986 Chevrolet Camaro?
Out of 101 Air Intakes for the 1986 Chevrolet Camaro, the most popular in our inventory are:
What are the top-rated 1986 Chevrolet Camaro Air Intakes?
Top-rated Air Intakes for your 1986 Chevrolet Camaro based on customer reviews/ratings are:
from
$16.99
(27)
Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg
“Works perfectly”
from
$451.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
