1986 Buick Electra Transmission Torque Converters

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

B&M Nitrous HoleShot 3000 stall for 1965-91 TH400, 425 and 1968-81 TH350, 375 transmissions (Not TH350C) is an excellent choice for vehicles with engine modifications, particularly big cams that tend to reduce low end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Nitrous Holeshot converters feature furnace brazed impeller and turbine, new precision steel alloy pump drive tube, new heavy duty needle bearings between the stator and impeller (not a thrust washer) and needle bearings between the stator and turbine. Other features include dual pattern 10.75 and 11.50-inch bolt circle, a new turbine hub, new springs and rollers in the stator and anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower that a nitrous plate system delivers. Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. These are serious converters for serious performance street cars. To prevent contamination left from worn parts being circulated in your new components causing premature wear, we strongly recommend protecting your investment by adding a B&M transmission cooler with all new transmission installations. Listed converters are NOT to be used in trans-brake applications. Not for use in trans-brake applications. Has both 10.75 and 11.50-inch bolt circles.

Hays Twister 3/4 Race performance torque converters are a perfect addition to our line of performance flexplates, clutches, and flywheels. Our 3/4 Race series of torque converters is intended for street/strip combinations, with various stall speed offerings to accommodate any mixture of modifications including higher compression ratios, aftermarket camshafts, aftermarket cylinder heads, lower gear ratios, and vehicle weight loss. The Twister 3/4 Race torque converter perfectly describes a converter suited for an application just shy of Full Race converter.

Hays Twister 3/4 Race Torque Converters–Good names never go away, and neither should good terms!

B&M Nitrous HoleShot 3500 stall for GM 1965-91 TH400, TH425, TH375 and 1968-81 TH350, TH375B (not TH350C.) The Nitrous Holeshot 3500 stall converter are an excellent choice for vehicles with many engine modifications, particularly big cams that tend to reduce low end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Nitrous Holeshot converters feature furnace brazed impeller and turbine, new precision steel alloy pump drive tube, new heavy duty needle bearings between the stator and impeller (not a thrust washer) and needle bearings between the stator and turbine. Other features include dual pattern 10.75 and 11.50-inch bolt circle, a new turbine hub, new springs and rollers in the stator and anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower that a nitrous plate system delivers. Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. These are serious converters for serious performance street cars. To prevent contamination left from worn parts being circulated in your new components causing premature wear, we strongly recommend protecting your investment by adding a B&M transmission cooler with all new transmission installations. Listed converters are NOT to be used in trans-brake applications. Not for use in trans-brake applications.

This Holeshot 3200 fits 1965-91 GM TH400, 425, 375 and 1968-81 TH350, 375B (not 350C) transmissions. Holeshot torque converters are for serious-minded performance enthusiasts and offer additional strength and durability features not found in our Tork Master or Traveler series of converters. The Holeshot 2400 converter is an excellent choice for vehicles with some performance engine modifications, particularly big cams that tend to reduce low-end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.

This remanufactured torque converter is designed to restore smooth engagement, reliable power transfer, and consistent drivability. Built using high-quality internal components and new seals where applicable, each unit is professionally assembled and tested to ensure dependable performance. Designed as a direct-fit replacement, it delivers factory-like operation for everyday driving conditions.