1986 Buick Electra Performance Ignition Products
More 1986 Buick Electra Performance Ignition Products
Find your specific 1986 Buick Electra original or aftermarket Performance Ignition Products below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 1986 Buick Electra Performance Ignition Products
Accel – Adj:Vac Adv GM V8 Hei Dist (Part No.31035)
from
$48.49
This unit permits a seamless wide range of adjustment to both amount and rate of ignition advance. This unit helps increase horsepower and throttle response. It provides maximum spark advance while preventing detonation or “pinging”. This kit includes an allen wrench for easy adjustment along with instructions.
Product Features:
See More
Product Features:
- Adjustable Vacuum Advance
- Increases Horsepower And Throttle Response
- Includes Allen Wrench For Adjustments
- Instantly Increase Horsepower
- Maximum Possible Spark Advance
- Not Legal For Sale/Use In CA
Accel – GM 86-99 Dis Supercoil (Part No.140017)
from
$72.99
Re-engineered to be the only true performance AC/Delco style DIS coil. “”Raised Dome”” construction, section bobbin technology, highly specialized silicone magnetic steel core, optimized windings, resistance, and turns ratio result in higher energy and voltage outputs, and longer dwell. Compatible with OE computer controlled ignition systems as well as Crane or MSD capacitive discharge DIS ignition systems. Brass contact increases energy transfer and resists corrosion better than aluminum. High dielectric strength “”ACCEL Yellow”” over molded housing. Packaged as single unit: 4 cyls require 2 coils, 6 cyls require 3 coils and 8 cyls require 4 coils.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Highly Specialized Silicone Magnetic Steel Cores
- Standard Motor Products SMP Dr-39
- MSD 8224
- Resist Corrosion
Accel – High Energy Ignition Coil for GM HEI – 1973-1991 (Part No.140003)
from
$100.99
Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Highly Specialized Silicone Magnetic Steel Cores
- Standard Motor Products SMP Dr-31
- MSD 8225
Accel – Supercoil (Part No.140001)
from
$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.
Product Features:
See More
Product Features:
- Oil Filled For Better Cooling
- Optimized Low Resistance
- Silicon Magnetic Steel E-Core
- Higher Energy/Voltage Outputs
- Quicker Starts
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
MSD Ignition – Mod HEI Dust Cover, V8 & Odd Fire V6 (Part No.8401)
from
$72.99
Stock style replacement modified HEI coil dust cover. Used on 8 cylinder vehicles only.
Product Features:
See More
Product Features:
- Externally mounted coil
- Increases reliability
- Increase performance
- High quality plastic
- Resist spark loss
- Use brass conductors
- Low resistance connections
- No modifications
MSD Ignition – Coil; GM Coil Pack; 2 Tower Style (Part No.8224)
from
$76.99
The updated Fuel Pump Booster is an easy way to maintain the proper fuel pressure on your car after adding a power adder such as a turbo or supercharger. The new model allows you to make your boost adjustments through a PC for improved control and accuracy. The Booster ensures that the engine receives the fuel it needs to make up for the increase in air being pumped into the intake manifold. It will increase the voltage to the factory fuel pump in proportion to manifold boost pressure in order to maintain the proper fuel delivery. The amount of increase is adjustable from a range of an additional 1.5 -22 volts up to 30 psi which can all be set and adjusted from your PC with MSD’s easy to use Windows based software. The MSD Booster will wire to the factory fuel pump relay or with a secondary booster pump.
Product Features:
See More
Product Features:
- Direct performance replacement
- For GM 2 Tower Coils Used From Mid 1980s To Late 1990s
- 80:1 turns ratio
- Lower Primary Resistance Produces High Voltage Output
- Works w/Stock Ignition As Well As MSD Ignitions
- CARB E.O. Approved
Accel – GM 1984-95 Remote Supercoil (Part No.140011)
from
$79.99
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Complete with new mounting hardware.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Highly Specialized Silicone Magnetic Steel Cores
- Standard Motor Products SMP DR-37
- MSD 8226
- Resist Corrosion
- W/New Mounting Hardware
Mallory – Unilite Ignition Module (Part No.605)
from
$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)
from
$134.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
Accel – Universal Fit Graphite Suppression; Spark Plug Wire Set (Part No.8026)
from
$128.99
These ACCEL carbon and graphite core wire sets virtually eliminate RFI noise, while providing maximum conductivity for ultimate performance in any race or street application. Double silicon insulation eliminates leakage and misfire.
Product Features:
See More
Product Features:
- Heavy Duty 8.8mm Oversized Silicone Jacket
- 500 Ohms/ft. Of Resistance
- 550 Degree Double Silicone Construction
- Fiberglass Braid
- Carbon/Graphite Core
- Magnetic Suppression
- Fiberglass/Kevlar Core
- 500 Ohms Resistance
Accel – Custom Fit Spark Plug Wire Set (Part No.8843)
from
$112.99
These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.
Product Features:
See More
Product Features:
- 8.8mm Graphite Suppression
- Silicone Spark Plug Boots
- 550 Degree Double Silicone Construction
- Fiberglass Braid
- Carbon/Graphite Core
- Magnetic Suppression
- Fiberglass/Kevlar Core
- 500 Ohms Resistance
MSD Ignition – Wire Set; Street Fire; Multi-Angle plug; HEI; Universal (Part No.5550)
from
$72.39
The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.
Product Features:
See More
Product Features:
- Helically wound conductor suppresses electro and radio noise
- Kevlar core combination for great strength and durability
- Heavy Duty Terminals For Secure Connection
- 8mm silicone and synthetic jacket resists heat and abrasion
- 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
- Silicone Boots Protect Against High Exhaust Temps
Popular 1986 Buick Electra Performance Ignition Products Categories
1986 Buick Electra Performance Ignition Products
Maybe you’re in the middle of a full rebuild of that 1986 Buick Electra. Maybe you just need a couple of Performance Ignition Products. Either way, Advance Auto Parts has 8 different Performance Ignition Products in our inventory ranging from $30.49 to $85.29. That means you can find the exact parts or products you need to keep that 1986 Buick Electra running smoothly.
Performance Ignition Products are only as good as their brand. We stock 3 different brands to make sure you have plenty of trusted parts to choose from for your 1986 Buick Electra. Accel, MSD Ignition, and Mallory are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Performance Ignition Products for your 1986 Buick Electra, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.
So if you’re in the market for aftermarket Performance Ignition Products to keep your 1986 Buick Electra rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Performance Ignition Products Brands To Make Your 1986 Buick Electra Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 1986 Buick Electra demands trusted brand parts and products to keep it running. Many trusted brands of Performance Ignition Products make up Advance Auto Parts’ inventory, and all are ready to help make your Electra the best it can be. Be sure to browse some of our top Performance Ignition Products brands and parts.
Popular Mallory Performance Ignition Products
We carry Mallory parts in our stock across Performance Ignition Parts categories, plus more. For a 1986 Buick Electra, our most popular Mallory Performance Ignition Products include:
Top 1986 Buick Electra Performance Ignition Products from Accel
Accel products are another trusted brand when it comes to Performance Ignition Products for your 1986 Buick Electra. Popular Accel parts include:
FAQs for 1986 Buick Electra Performance Ignition Products
What are the most purchased Performance Ignition Products for the 1986 Buick Electra?
Out of 8 Performance Ignition Products for the 1986 Buick Electra, the most popular in our inventory are:
from
$72.39
(3)
Wire Set; Street Fire; Multi-Angle plug; HEI; Universal
Performance Spark Plug Wires
