1985 Subaru RX Belts and Hoses
More 1985 Subaru RX Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1985 Subaru RX, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1985 Subaru RX Belts and Hoses
Gates – Premium Molded Coolant Hose (Part No.20338)
from
$9.79
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 8 1/4 Inch Length (Part No.86800)
from
$28.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Heater Hose (Part No.18020)
from
$14.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 3.25" Long, .63" Diameter (Part No.A70001)
from
$10.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 14 1/4 Inch Length (Part No.87649)
from
$11.79
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Bando – Precision Engineered V-Belt (Part No.W100052071BAN)
from
$19.47
Bando has been manufacturing rubber products for over 100 years. Bando is the OEM supplier to over 80 percent of the top 10 cars sold in the U.S. (by volume). Bando belts are made with EPDM rubber which adheres to OEM specification that is more heat resistant and long lasting. With 19 plants worldwide, Bando are the 3rd largest manufacturer of automotive drive belts in the world. Bando’s automotive belts, serpentine, timing and V-belts are engineered to meet the unique requirements of today’s high performance engines for applications that run the gamut from international racing teams to light duty trucks. Bando manufactures belts for the world’s leading automakers, supplying both OEM and aftermarket applications, all to the same exacting standards of quality.
Product Features:
See More
Product Features:
- Designed to provide the positive no-slip drive requirements needed on demanding overhead cam applications
- Precision molded teeth are protected by durable fabric facing for long life
- Tensile cord is engineered and tested for maximum load carrying capabilities
- Rubber backing resists abrasion, oil and heat
Bando – Precision Engineered V-Belt (Part No.W100046543BAN)
from
$8.43
Bando has been manufacturing rubber products for over 100 years. Bando is the OEM supplier to over 80 percent of the top 10 cars sold in the U.S. (by volume). Bando belts are made with EPDM rubber which adheres to OEM specification that is more heat resistant and long lasting. With 19 plants worldwide, Bando are the 3rd largest manufacturer of automotive drive belts in the world. Bando’s automotive belts, serpentine, timing and V-belts are engineered to meet the unique requirements of today’s high performance engines for applications that run the gamut from international racing teams to light duty trucks. Bando manufactures belts for the world’s leading automakers, supplying both OEM and aftermarket applications, all to the same exacting standards of quality.
Product Features:
See More
Product Features:
- Designed to provide the positive no-slip drive requirements needed on demanding overhead cam applications
- Precision molded teeth are protected by durable fabric facing for long life
- Tensile cord is engineered and tested for maximum load carrying capabilities
- Rubber backing resists abrasion, oil and heat
Bando – Precision Engineered V-Belt (Part No.W100064700BAN)
from
$8.13
Bando has been manufacturing rubber products for over 100 years. Bando is the OEM supplier to over 80 percent of the top 10 cars sold in the U.S. (by volume). Bando belts are made with EPDM rubber which adheres to OEM specification that is more heat resistant and long lasting. With 19 plants worldwide, Bando are the 3rd largest manufacturer of automotive drive belts in the world. Bando’s automotive belts, serpentine, timing and V-belts are engineered to meet the unique requirements of today’s high performance engines for applications that run the gamut from international racing teams to light duty trucks. Bando manufactures belts for the world’s leading automakers, supplying both OEM and aftermarket applications, all to the same exacting standards of quality.
Product Features:
See More
Product Features:
- Designed to provide the positive no-slip drive requirements needed on demanding overhead cam applications
- Precision molded teeth are protected by durable fabric facing for long life
- Tensile cord is engineered and tested for maximum load carrying capabilities
- Rubber backing resists abrasion, oil and heat
ContiTech – Drive V-Belt (Part No.W100033156CON)
from
$18.65
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Polyester fiber tensile members and a ribbed belt design.
Dayco – Bottom Cog V-Belt: 35.5" Long, Exact Fit Premium Quality (Part No.17355)
from
$14.29
Dayco® High Performance V-Belt is the workhorse of the heavy-duty industry. Polyester cord provides maximum power transfer and tension holding capability for the life of the belt. The laminated construction helps absorb greater shock loads associated with diesel engines. These Dayco® High Performance V-Belt advantages translate into less downtime, lower maintenance costs, and increased dependability. Dayco’s High Performance V-Belt meets or exceeds SAE J636 and J637 specifications.
Product Features:
See More
Product Features:
- The High Performance V-Belt design delivers more flexibility and increases airflow around the belt, so it runs cooler and lasts longer than most competitive belts
- Polyester cord provides maximum power transfer and tension holding capability for the life of the belt
- The laminated construction helps absorb greater shock loads associated with diesel engines
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
ContiTech – Drive V-Belt (Part No.W100039125CON)
from
$14.47
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Polyester fiber tensile members and a ribbed belt design.
ContiTech – Drive V-Belt (Part No.W100033196CON)
from
$15.82
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Polyester fiber tensile members and a ribbed belt design.
Gates – Premium Molded Coolant Hose (Part No.21779)
from
$38.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Flex Radiator Hoses; EPDM Rubber, 11 Inch Long, 1.25 Inch Inner Dia. (Part No.81031)
from
$27.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.13" Diameter (Part No.B71260)
from
$23.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.21584)
from
$24.29
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25251)
from
$30.49
Product Features:
See More
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10" Long, 1.13" Diameter (Part No.B71277)
from
$20.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10.25" Long, 1.13" Diameter (Part No.B71404)
from
$24.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Popular 1985 Subaru RX Belts and Hoses Categories
1985 Subaru RX Belts and Hoses
You count on your 1985 Subaru RX to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 19 Belts and Hoses ranging in price from $2.99 to $79.99, you’re sure to find everything you need for your 1985 Subaru RX.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 4 different brands like Dayco, Imperial, and Gates. 1985 Subaru RX Belts and Hoses start as low as $2.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 50 extensive product reviews on 1985 Subaru RX Belts and Hoses.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1985 Subaru RX below to get started!
Top-Rated Belts and Hoses Brands For Your 1985 Subaru RX
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1985 Subaru RX running right for years to come. In our inventory you’ll find brands like Dayco, Imperial, Gates, and even more.
Popular Dayco Belts and Hoses
You’ll find popular Dayco brand products across Serpentine and V Belts and Radiator Hoses. All are waiting to get your 1985 Subaru RX back on the road. Some of the top-rated Dayco products in these categories are:
from
$23.99
(30)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.13" Diameter
Coolant Hoses
from
$20.99
(3)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10" Long, 1.13" Diameter
Upper Radiator Hoses
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1985 Subaru RX, and some of our most reviewed Dayco parts include:
from
$28.99
(3)
Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 8 1/4 Inch Length
By-Pass Hoses
FAQs for 1985 Subaru RX Belts and Hoses
What are the most purchased Belts and Hoses for the 1985 Subaru RX?
Out of 19 Belts and Hoses for the 1985 Subaru RX, the most popular in our inventory are:
from
$11.79
This product is not rated
Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 14 1/4 Inch Length
Heater Hoses
