1984 Dodge Diplomat Differentials

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

• Fits Chrysler 9.25″ rear
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Yukon yoke for Chrysler 7.25″ and 8.25″ with a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler 7.25″ and 8.25″
• 27 spline
• 7260 u-joint size
• Inside snap ring design
• 2.125″ snap ring span
• 1.078″ cap diameter
• Strap style

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Chrysler 9.25″ rear
• Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Chrysler 9.25″ rear differential. This kit contains carrier bearings and races.

Product Features:

• Fits Chrysler 9.25″ rear
• Includes carrier bearings and races

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

• Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Chrysler 8.25″ with 27 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

Product Features:

• Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
• 3/8″ x 24 thread
• .866″ long

Positraction clutch guide.

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
• Compatible with Dura Grip positractions only

Differential carrier side bearing screw adjuster for Chrysler 7.25″ and 8.25″.

Product Features:

• Side adjuster
• Fits Chrysler 7.25″ and 8.25″

Product Features:

• Fits Chrysler 9.25″ rear with open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Chrysler 8.25″ open differntial with 27 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Toyota wheel seal for ’80-’97 Full float Landcruiser outer rear, ’86-’95 dually pick-up.Yukon Mighty seal.

Product Features:

• Fits Chrysler 9.25″ rear
• Chrome

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

• Side adjuster for Chrysler 9.25″ rear

Product Features:

• Cross pin bolt for Dana Spicer 60 with c-clip axles

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

• Fits Chrysler 8.25″
• 8.25″ ring gear diameter
• 27 spline pinion
• 10 ring gear bolts
• 3.90 ratio

7.25″ & 8.25″ Chrysler pinion seal.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Chrysler 7.25″ and 8.25″

Product Features:

• SUPER KIT-CHRY 8.25 *TIMKIN*

Cross pin shaft for 8.25″ Chrysler.

Product Features:

• Cross pin shaft for Chrysler 8.25″
• Fits standard open differentials only

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

• Includes three quarts of conventional oil

Product Features:

• Standard open carrier case
• Fits 2009 and down Chrysler 9.25″ rear
• Does not include spider gears

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 2000 and down Chrysler 9.25″ rear
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Product Features:

• Pinion nut
• Fits Chrysler 7.25″, 8.0″, 8.25″, 9.25″ and 8.75″ with 29 spline pinion

This differential cover plug is designed to match the fit & function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

• Direct replacement – this differential cover plug matches the fit and function of the factory part on specified years, makes and models.
• Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience