1984 Chevrolet Caprice Performance and Racing Products

Popular 1984 Chevrolet Caprice Performance and Racing Products Categories

Essential Performance and Racing Products for 1984 Chevrolet Caprices

Mr. Gasket – Oil Filter Conversion Kit (Part No.1270)

Oil Filter Conversion Kit

from

$32.99
This kit converts the bolt-on, can-type filter to a full-flow easy spin-on filter. The one-piece construction allows easy installation for a fast, clean filter change.

Product Features:
  • Fits Chevrolet 1957-1967 small block and Big Block 1965-1967.
  • Converts a bolt-on, can-type filter to a full-flow, spin-on filter.
  • Includes O-ring And Hardware.
  • Uses the following Filters: Fram PH5(Tall) OR PH30, Wix 51069, AC Delco PF-25 or PF-35.
See More

Mr. Gasket – Starter Motor Heat Shield (Part No.3678)

Starter Motor Heat Shield

from

$43.99
Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:
  • Designed to prevent starter overheat due to extreme exhaust temperature
  • Heat resistant material sandwiched between 2 aluminum plates
  • Protects Starter From High Temperatures
  • Made Of 2 Sheets Of Aluminum Heat Resistant Center
  • Natural Finish
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Moderate Sound (Part No.842451)

50 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Moderate Sound

from

$175.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More

Holley – High-Flow Mechanical Fuel Pump for Street Performance (Part No.12-834)

High-Flow Mechanical Fuel Pump for Street Performance

from

$124.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:
  • Street Performance
  • Flows 80 gph Free Flow
  • Shutoff Pressure Pre-Set 7.5 PSI
  • Fuel Pressure Regulator Is Not Required
  • Heavy Duty Construction For Continuous High rpm Operation
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • Inlet And Outlet Tapped For 1/4 in. NPT
  • Inlet/Outlet Tapped For .25 in. NPT
See More

FEL-PRO Performance – PERFORMANCE VALVE COVER GASKET SET (Part No.1602)

PERFORMANCE VALVE COVER GASKET SET

from

$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Die cut silicone rubber gaskets conform to out-of-flat covers
  • Great for on-again/off-again situations
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

from

$111.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Mr. Gasket – Intake Bolt Kit (Part No.5003)

Intake Bolt Kit

from

$75.99
Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:
  • Chrome plated
  • Grade 8
  • 12-point head
  • AN washers with no exposed shoulder for a professional appearance
See More

Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)

Tie Rod Dust Boot

from

$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:
  • Easy to Install
  • Superior Material
  • Saves Your Tie Rods
  • Lasts Longer
  • Looks Great
See More

Mr. Gasket – Intake Gasket Set – Standard Duty – Big Block Chevy With Stock Rectangle Ports – 1.75"W X 2.50"H (Part No.108)

Intake Gasket Set - Standard Duty - Big Block Chevy With Stock Rectangle Ports - 1.75"W X 2.50"H

from

$29.99
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Die-cut for an excellent fit
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals & distributor gaskets if applicable
  • For OE replacement, high performance street, drag race and oval track use
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Performer Series Retainer (Qty 16)

from

$99.99
Product Features:
  • Use W/ Valve Springs Part #5703, 5794
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Weiand – Action Plus Water Pumps (Part No.9208P)

Action Plus Water Pumps

from

$215.99
Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:
  • Twisted Snout Water Pump Design For Updated Style
  • Street Performance
  • Heavy Duty Shaft w/5/8 in. Pilot
  • Six-Blade Stamped Steel
  • Anti-Cavitation Impeller
  • 100 Percent Leak Tested
See More

Energy Suspension – Control Arm Bushing Set (Part No.3.3167R)

Control Arm Bushing Set

from

$55.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:
  • Maintains Better Alignment While Driving
  • Full Floating and Non Binding
  • Fits Into the Remaining Stock Control Arms
See More

Edelbrock – Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet (Part No.3702)

Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet

from

$306.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched to Edelbrock Performer Intakes
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

Hooker Headers – LS1 Swap Headers for 66-72 Chevelle, El Camino, Monte Carlo & Sprint (Part No.2455-1HKR)

LS1 Swap Headers for 66-72 Chevelle, El Camino, Monte Carlo & Sprint

from

$552.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Chevrolet Small Block w/ 3/8" Stud (Part No.19002-16)

Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Chevrolet Small Block w/ 3/8" Stud

from

$412.99
These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Chevrolet V8 265-400 applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:
  • CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
  • Designed for high performance street and race engines
  • Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
  • Additional clearance, up to 1.650″ O.D. valve spring
See More

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2919)

Engine Crankshaft Seal Kit

from

$37.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1025)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$72.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Hypertech – ThermoMaster Power Chip (Part No.11832)

ThermoMaster Power Chip

from

$168.89
Hypertech ThermoMaster Power Chips are engineered for stock 1995-1981 GM vehicles (premium octane fuel required). The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. ThermoMaster Power Chips are designed for daily street driving or competition in unmodified vehicles using a 160 Deg. or 180 Deg. thermostat. Hypertech Power Chips(TM) are emissions certified 50-state legal (application specific).

Product Features:
  • Use w/Low-Temp 160-180 Deg. PowerStat Thermostat
  • Controls Engines Air/Fuel Ratio
  • Controls Spark Advance For Max Power
  • Potential Gas Mileage Improvements
  • No Wiring Or Soldering Required
  • Installs In Less Than 30 Minutes
  • Product might not be available in all states due to local laws.
See More

Edelbrock – Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp) (Part No.70090)

Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp)

from

$875.99


Product Features:
  • Designed For Carbureted V8s
  • Power Increases From 100-250 HP
  • Precision EDM Machined Spray Bars
  • Simple To Install
See More

Energy Suspension – Hyper-Flex System (Part No.3.18120R)

Hyper-Flex System

from

$328.99
Product Features:
  • Incredible Improvement in Control
  • Maintains Proper Caster and Camber Alignment
  • Increase in Handling and Control
  • Greatly Reduce Wheel Hop on Quick Acceleration
  • Even Braking Control is Improved
  • Better Suspension Stability
See More

Spectre – Pulley (Part No.4448)

Pulley

from

$82.99
Spectre’s Triple Groove Pulley was designed for the ’69-’85 small block Chevrolet with a long water pump. This crankshaft pulley with triple belt groove is triple chrome plated steel. Measuring 7 3/4 inches in diameter the triple groove pulley is engineered for optimum fit and function. Note – identify the water pump by looking at the distance between it and the timing cover. Long water pumps are about 1 inch away from the timing cover.

Product Features:
  • Triple chrome-plated steel
  • Triple belt groove
  • 7-3/4 In. diameter
  • Easy to install
See More

Accel – High Performance Ignition Module for GM HEI Distributors (Part No.35361)

High Performance Ignition Module for GM HEI Distributors

from

$69.99
This high performance HEI module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most GM HEI for V8 engines with the 4 pin module 1974 thru 1985

Product Features:
  • Fits Most Stock And Modified Distributors
  • Solid State Electronics
  • Dwell Control Circuit
See More

Mr. Gasket – Enhancement Products (Part No.2060)

Enhancement Products

from

$10.49
This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:
  • Internally battled
  • High-porosity filter
  • Ideal for high performance
  • Includes rubber grommet
See More

B & M – Automatic Shifter, Light Truck Megashifter (Part No.80680)

Automatic Shifter, Light Truck Megashifter

from

$479.99
The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. The light truck Megashifter is better suited for truck and bench seat applications with its overall height of 14.85-inches tall (2.25-inches taller than #80690 Megashifter.) The positive ratcheting action won’t allow you to over-shift and miss a gear at that critical moment, along with the reverse lockout feature meets NHRA/IHRA safety rules for those weekend grudge races at the track, while the look and feel of the T-handle and accordion style shift boot really shows off its racing heritage. Other features include a black console that you can trim to match the contour of your vehicle’s floor, 5-foot long shifter cable, cable brackets, transmission shift levers, chrome plated top plate with lighted gear indicator and everything needed for an easy at home installation. An optional T-handle with a 12-volt button is available separately for actuating a trans-brake, nitrous oxide or other accessories for the hard-core performance enthusiast. This shifter fits most popular Chrysler, Ford and GM 3 and 4-speed automatic transmissions. Note: AOD transmissions require optional kit #40496, GM 4L60E through 4L85E transmissions with PRNDL switch will require optional kit #70499. Overall Dimensions – 14.9L x 6.4W x 14.8H

Product Features:
  • Universal Floor Mount Application
  • Cable Operated
  • Quick Installation
  • Accurate Shifting
  • NHRA/IHRA Reverse Lockout Meets Requirements
  • Use w/Reverse Pattern Valve Body
  • Includes Neutral Safety Switch
  • Includes Backup Light Switch
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$30.49


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

Lakewood – Drag Shock-70/30:GM (Rear) (Part No.40310)

Drag Shock-70/30:GM (Rear)

from

$104.99
The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:
  • Excellent Weight Transfer
  • Lets Front End Down Quickly
  • Maximum Traction
  • Makes Vehicle Safer
  • Easier Control At End Of Track
  • Better Overall Stability
See More

Upgrade your 1984 Chevrolet Caprice with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1984 Chevrolet Caprice, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Chevrolet or enhancing its overall performance, Performance and Racing Products are key to keeping your Caprice functioning at its best. At Advance Auto Parts, we offer a wide selection of 241 Performance and Racing Products for the 1984 Chevrolet Caprice, designed to meet your needs without breaking the bank. From Performance Ignition Product replacements to Performance Oil Filters upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1984 Chevrolet Caprice at great prices. Our Performance and Racing Products inventory for this model ranges from just $9.99 to $1,138.99, with an average price of $236.29. Our 241 Performance and Racing Products in stock come from 25 trusted brands, so you’re sure to find the right part for your 1984 Chevrolet Caprice without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1984 Chevrolet Caprice, we stock popular OEM and aftermarket Performance and Racing Products from top names like K&N, Mr. Gasket, Edelbrock, and more. K&N Performance and Racing Products start at just $17.99 and boast an impressive 5 stars average rating from customers. Mr. Gasket and Edelbrock also bring quality to the table, with Performance and Racing Products available starting at $9.99, and at an average 4 stars rating. With 768 customer reviews and counting, our 1984 Chevrolet Caprice Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1984 Chevrolet Caprice is always ready to roll. We’re committed to providing you with everything you need to keep your Caprice in top shape, all in one place. Start shopping confidently below for your 1984 Chevrolet Caprice!

Best-Selling Performance Ignition Products for 1984 Chevrolet Caprices

Enhance the driving experience in your Chevrolet with 11 quality Performance Ignition Product components, starting at $30.49.

Accel – High Energy Ignition Coil for GM HEI – 1973-1991 (Part No.140003)

High Energy Ignition Coil for GM HEI - 1973-1991

from

$100.99
Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:
  • 10-15% More Energy
  • Direct Plug In Replacement Direct OE Fit
  • Advanced Bobbin Technology
  • Highly Specialized Silicone Magnetic Steel Cores
  • Standard Motor Products SMP Dr-31
  • MSD 8225
See More

MSD Ignition – High Energy Ignition Coil for GM HEI Distributors (Part No.8225)

High Energy Ignition Coil for GM HEI Distributors

from

$112.99
HEI owners now have a choice to replace their stock coil with the MSD high energy unitized coil for GM HEI distributors. This coil is a direct replacement of the stock coil and offers increased spark energy when used with the MSD HEI module, PN 83645. The coil features special low induc?tance, high temperature windings which charge faster to give you increased spark energy at higher rpm. The premium epoxy filled construction is designed to withstand harsh race applications as well as the wear and tear that daily usage dishes out, and still deliver more spark energy to the spark plugs.

Product Features:
  • Direct performance replacement for GM HEI coil-in-cap dist.
  • 70:1 Turns Ratio
  • Lower Primary Resistance Produces High Voltage Output
  • Full Power Sparks To 9000 Rpm w/PN[83647] MSD HEI Module
See More

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Accel – GM Hei Supercoil Red/White (Part No.140005)

GM Hei Supercoil Red/White

from

$113.99
Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:
  • 10-15% More Energy
  • Direct Plug In Replacement Direct OE Fit
  • Advanced Bobbin Technology
  • Highly Specialized Silicone Magnetic Steel Cores
  • Similar to Standard Motor Products SMP Dr-32
  • Long Life And Great Looks
See More

Accel – High Performance Ignition Module for GM HEI Distributors (Part No.35361)

High Performance Ignition Module for GM HEI Distributors

from

$69.99
This high performance HEI module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most GM HEI for V8 engines with the 4 pin module 1974 thru 1985

Product Features:
  • Fits Most Stock And Modified Distributors
  • Solid State Electronics
  • Dwell Control Circuit
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$30.49


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

MSD Ignition – Crank Trigger Kit; Small Block Chevy; 6? Balancer (Part No.8600)

Crank Trigger Kit; Small Block Chevy; 6? Balancer

from

$461.99
For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:
  • 6.25 in. Diameter
  • Absolutely the most accurate way to trigger the ignition.
  • The non-magnetic pickup cannot be false triggered.
  • Powerful magnets are embedded in a billet aluminum trigger wheel.
See More

MSD Ignition – Trigger Wheel; Flying Magnet; Small Block Chevy (Part No.8611)

Trigger Wheel; Flying Magnet; Small Block Chevy

from

$290.99
For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:
  • Replacement crank trigger wheel for small block Chevy
  • Absolutely the most accurate way to trigger the ignition
  • The non-magnetic pickup cannot be false triggered
  • Powerful magnets are embedded in a billet aluminum trigger wheel
See More

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Promaster Classic Series; Ignition Coil

from

$186.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:
  • Glass Filled Polyester Case
  • Longer Spark Duration
  • Increased Performance
  • No Energy Loss Due To Arcing
  • Includes Brass Contact Terminal
See More

Accel – Custom Fit 8.8mm; Spark Plug Wire Set (Part No.8849)

Custom Fit 8.8mm; Spark Plug Wire Set

from

$113.99
These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:
  • 8.8mm Graphite Suppression
  • Silicone Spark Plug Boots
  • 550 Degree Double Silicone Construction
  • Fiberglass Braid
  • Carbon/Graphite Core
  • Magnetic Suppression
  • Fiberglass/Kevlar Core
  • 500 Ohms Resistance
See More

MSD Ignition – Mod HEI Dust Cover, V8 & Odd Fire V6 (Part No.8401)

Mod HEI Dust Cover, V8 & Odd Fire V6

from

$72.99
Stock style replacement modified HEI coil dust cover. Used on 8 cylinder vehicles only.

Product Features:
  • Externally mounted coil
  • Increases reliability
  • Increase performance
  • High quality plastic
  • Resist spark loss
  • Use brass conductors
  • Low resistance connections
  • No modifications
See More

Most Popular 1984 Chevrolet Caprice Performance Oil Filters

Customize your Chevrolet with 4 Performance Oil Filters products like Performance Oil Filters and Performance Oil Filler Caps, all priced under $42.99.

K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2002)

Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine

from

$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:
  • HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
  • VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
  • PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
  • EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
  • EASY TO REMOVE: Fast and easy Wrench-Off removal
  • HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
  • HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
See More

Mr. Gasket – Enhancement Products (Part No.2060)

Enhancement Products

from

$10.49
This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:
  • Internally battled
  • High-porosity filter
  • Ideal for high performance
  • Includes rubber grommet
See More

Mr. Gasket – Chrome Oil Fill Cap – Push-On Style W/Tube For Pvc Hookup – Fitting For Easy Pcv Hose Hook Up (Part No.2063)

Chrome Oil Fill Cap - Push-On Style W/Tube For Pvc Hookup - Fitting For Easy Pcv Hose Hook Up

from

$12.99
This chrome-plated steel push-on breather/oil filler cap fits over your oil filler tube. It has a side fitting for easy PCV hose (positive crankcase ventilation) hook up. Perfect compliment to Mr. Gasket matching chrome oil filler tube, #2066

Product Features:
  • Chrome plated steel
  • Fits stock factory oil filler tubes
  • Features side PCV hook up tube
  • Includes Rubber Grommet
See More

Mr. Gasket – Oil Filter Adapter (Part No.1272)

Oil Filter Adapter

from

$42.99
This oil filter adapter kit replaces the factory GM (General Motors) oil filter adapter and is manufactured from high grade aluminum. Required for Chevrolet crate engines that does not include an oil filter adapter. Replaces oil filter adapter’s damaged when removing engines to be overhauled. Oil filtered adapter includes filter bypass valve. Uses the following Chevrolet oil filters – AC Delco PF-25 or PF35, Fram PH5 (tall) or PH30, and WIX 51069. Includes mounting bolts.

Product Features:
  • Replaces GM Oil Filter Adapter #3952301 and 19299222
  • Fits Chevrolet 307-400 V8 1968-86 and 396-454
  • Attaches Spin-on Oil Filter To Engines Block
  • Embossed base provides a leak-free sealing surface. Kit does not come with a gasket
  • Kit includes Oil Filter adapter and (2) 5/16″-18 x 1.00″ long bolts
  • Uses the following Filters: Fram PH5(Tall) OR PH30, Wix 51069, AC Delco PF-25 or PF-35.
See More

Top Picks for 1984 Chevrolet Caprice Performance Engines

Upgrade Chevrolet Caprices with top-quality Performance Engines parts, including 86 OEM and aftermarket selections for your 1984 model.

Edelbrock – Performer EPS Intake Manifold for 1955-86 Small-Block Chevy (Part No.2701)

Performer EPS Intake Manifold for 1955-86 Small-Block Chevy

from

$195.99


Product Features:
  • Maximizes Performance with Edelbrock Carburetors
  • Runners Tuned to Match Square Bore Carburetor
  • Maximizes Peak Torque Around 3500 RPM
  • Excellent Throttle Response and Mid-Range Power
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Prod. +5 HP and +9 ft/lbs. of Torque Over PN[2101]
See More

FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1003)

Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts

from

$39.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1004)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$52.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Engine Valve Cover Gasket Set

from

$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish (Part No.2104)

Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish

from

$329.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 Deg Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
  • Accepts Late-Model Choke; Waterneck; and HEI
  • Accepts A/C And Alternator
  • Accepts Exhaust Heated Chokes
See More

Competition Cams – MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST (Part No.1412-16)

MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST

from

$213.99
These Magnum Roller Rocker Arms for Chevy V8 265-400 and V6 200-262 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.52 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed

Product Features:
  • Roller tip reduces friction while stiff design and superior ratio accuracy yield more effective valve lift
  • For applications with less than 350 lbs. of open spring pressure
  • Constructed from 8620 chromemoly steel, a superior material that will not flex and ensures maximum lift
  • Ultimate street roller rocker arm designed for serious performance enthusiasts
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

from

$151.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Non-Rotator Style: Dyno Tested and Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

FEL-PRO Performance – PERFORMANCE VALVE COVER GASKET SET (Part No.1602)

PERFORMANCE VALVE COVER GASKET SET

from

$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Die cut silicone rubber gaskets conform to out-of-flat covers
  • Great for on-again/off-again situations
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Pushrod Set for S/B Chevy (Part No.9630)

Pushrod Set for S/B Chevy

from

$189.99


Product Features:
  • Case-Hardened Tubing
  • Welded Ends
  • 5/16 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Weiand – Action Plus Water Pumps (Part No.9240P)

Action Plus Water Pumps

from

$215.99
Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:
  • Twisted Snout Water Pump Design For Updated Style
  • Street Performance
  • Heavy Duty Shaft w/5/8 in. Pilot
  • Six-Blade Stamped Steel
  • Anti-Cavitation Impeller
  • 100 Percent Leak Tested
See More

Weiand – Action Plus Water Pumps (Part No.9208P)

Action Plus Water Pumps

from

$215.99
Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:
  • Twisted Snout Water Pump Design For Updated Style
  • Street Performance
  • Heavy Duty Shaft w/5/8 in. Pilot
  • Six-Blade Stamped Steel
  • Anti-Cavitation Impeller
  • 100 Percent Leak Tested
See More

Edelbrock – Valve Cover Gasket Set for Chevrolet (Part No.7549)

Valve Cover Gasket Set for Chevrolet

from

$35.99
Product Features:
  • Valve Cover Gasket
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1800)

PERFORMANCE OIL PAN GASKET SET

from

$18.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

from

$111.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers

from

$17.49
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:
  • Zinc plated to resist corrosion and provide a clean professional appearance
  • Made from Grade 5 steel for strength and durability
  • Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
  • Allen (socket) Head
  • Zinc Plated For Protection
See More

Spectre – Water Neck; Olds (Part No.4733)

Water Neck; Olds

from

$26.99
Spectre’s Oldsmobile V8 water neck fits Oldsmobile 330, 350, 425 and 455 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck has an additional by-pass hose connection and includes the bolts.

Product Features:
  • Fits Oldsmobile 330, 350, 425 and 455 engines
  • Chrome plated
  • Bolts included
  • Designed for OEM fit
  • Easy to install
  • O-ring/gasket not included
See More

Mr. Gasket – Bolt Water Pump (Part No.4998)

Bolt Water Pump

from

$32.99
This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:
  • Chrome Plated
  • Grade 5
  • AN washers with no exposed shoulder for a professional appearance
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1010)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$39.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

from

$65.99
Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Mr. Gasket – Valve Cover Gasket Set (Part No.585G)

Valve Cover Gasket Set

from

$29.49
Molded rubber gaskets are reusable, great for engines that require valve lash maintenance. These gaskets feature Nitrile material for long life, solid steel carrier for strength and rigidity. Incorporates compression limiters to prevent fastener over-tightening.

Product Features:
  • Features Nitrile Rubber Material For Long Life
  • Molded Rubber Gaskets Are Reusable
  • Ideal For Engine Requiring Valve Lash Maintenance
See More

Edelbrock – Intake Manifold Gasket for 1985-1995, Chevy V6 200-229-262 (Part No.7209)

Intake Manifold Gasket for 1985-1995, Chevy V6 200-229-262

from

$27.99
Edelbrock part #7209 Intake Gaskets for 1985-1995, Chevy V6 200-229-262 (3.8 and 4.3L) allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-

Product Features:
  • 1.28″x2.10″
  • Stock Port Style
  • .060″ Thick
  • Multi Piece Configuration
  • Composite Material
See More

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

Cylinder Head Dowel Pins

from

$14.99
Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Engine Timing Cover Gasket

from

$20.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Steel core gasket construction
  • Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Performer Small-Block Chevy Intake Manifold for Street Performance (Part No.3701)

Performer Small-Block Chevy Intake Manifold for Street Performance

from

$339.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 Deg Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
  • Accepts Late-Model Choke; Waterneck; and HEI
  • Accepts A/C And Alternator
  • Accepts Exhaust Heated Chokes and Accepts EGR
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1960)

Rear Main Seal Gasket

from

$23.99
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

Competition Cams – Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height (Part No.981-16)

Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height

from

$126.99
Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:
  • Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
  • O.D.: 1.254″, I.D.: .880″
  • Single valve springs with damper
  • Approximately .490″ max lift at recommended installed height
See More

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5780G)

Ultra Seal: Head Gasket

from

$64.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 3.870 inch, Compressed thickness 0.028 inch

Product Features:
  • Five layer (graphite core/perforated steel outer layers) composite construction
  • Graphite core has excellent thermo-conductivity-transfers heat away from hot spots in head preventing gasket burn-out
  • Provides excellent stability, compressibility and high temperature endurance
  • Coated with high temperature silicone to ensure sealing of engine fluids
  • Will not brinell (indent) aluminum cylinder heads
  • For high performance street, drag race and oval track use
  • Compatible w/High Octane Fuel
  • Compatible With Exotic Fuel
See More

Mr. Gasket – Intake Gasket (Part No.116)

Intake Gasket

from

$40.19
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material.
  • Provides excellent sealing and durability.
  • Can be trimmed if necessary for modified port applications.
  • Complete with manifold end seals and distributor gasket.
  • For OE replacement, high performance street, drag race and oval track use.
See More

Mr. Gasket – Head Gasket (Part No.1130G)

Head Gasket

from

$32.99
Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.

Product Features:
  • Manufactured from .020″ steel shim stock.
  • Thinner than composition head gaskets – increases engine compression.
  • Stress formed embossments seal extreme cylinder pressures.
  • For high performance street, drag race and oval track use.
See More

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 3 Piece Set (Part No.1200)

Lower Intake Manifold Gasket Set: 3 Piece Set

from

$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
  • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
  • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
  • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
  • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1818)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire (Part No.5487)

Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire

from

$367.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched To Performer Intake PN[5486]
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

Edelbrock – Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy (Part No.2703)

Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy

from

$322.99
Edelbrock part #2703 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thro

Product Features:
  • Idle-5500 RPM Range
  • Dual Plane Type-4150 Style Flange
  • 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
  • Satin Finish
  • Non-EGR W/ Oil Fill Tube
See More

Edelbrock – Pushrod Set for S/B Chevy (Part No.9629)

Pushrod Set for S/B Chevy

from

$187.99


Product Features:
  • Case-Hardened Tubing
  • Surface Hardening
  • Welded Ends
  • 0.3125 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Competition Cams – CAMSHAFT, SBC 295 BIG MUTHA THUMPR HYDRAULIC 1 EA (Part No.12-602-4)

CAMSHAFT, SBC 295 BIG MUTHA THUMPR HYDRAULIC 1 EA

from

$529.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Competition Cams – CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA (Part No.12-250-3)

CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA

from

$258.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Competition Cams – Magnum 7.800" Long, .080" Wall, 3/8" Diameter Pushrod Set (Part No.7513-16)

Magnum 7.800" Long, .080" Wall, 3/8" Diameter Pushrod Set

from

$157.99
Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:
  • 3/8″ Diameter, 7.800″ Length
  • Magnum Pushrods for Small Block Chevy
  • One-piece .080″ wall chromemoly steel tubing
  • Heat-treated for extended durability and guide plate compatibility
  • Precision formed and reinforced pushrod end
See More

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Ultra Seal: Competition Screw-In Rocker Arm Studs

from

$94.99
Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Prevents Stud Flexing
  • Black Plated Finish
See More

FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1000)

Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts

from

$59.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Ultra Seal: Screw-In Rocker Arm Studs (Part No.1076)

Ultra Seal: Screw-In Rocker Arm Studs

from

$65.99
Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Grade 8 Steel
See More

Mr. Gasket – Engine Sealing (Part No.6560)

Engine Sealing

from

$499.99
Manufactured from cellulose and nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement, high performance street, drag race and oval track.

Product Features:
  • Made of high temp silicone or nitrile blend rubber
  • Torque limiters to prevent over tightening
  • One piece molded rubber
  • Fits left and right hand dipsticks
See More

Mr. Gasket – Intake Gasket (Part No.143)

Intake Gasket

from

$42.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Die-cut for an excellent fit
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
See More

Edelbrock – Intake Manifold replacement base to top gasket (Part No.6999)

Intake Manifold replacement base to top gasket

from

$17.99
Replacement gasket for top to bottom. See PN(7110) complete. PN(7067) bottom. PN(7032) top. Includes base and top for intake manifold PN(7110).

Product Features:
  • Replacement Gasket for Top to Bottom
  • See PN[7110]Complete; PN[7067]Bottom; PN[7032] Top
See More

Edelbrock – Performer Buick 3.8L, 4.1L V6 Intake Manifold (Part No.5486)

Performer Buick 3.8L, 4.1L V6 Intake Manifold

from

$381.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • Not for C-3 and C-4 Electronic Fuel Mngmt Systems
See More

Mr. Gasket – Ultra Seal: Sure-Lock Rocker Arm Nuts (Part No.923G)

Ultra Seal: Sure-Lock Rocker Arm Nuts

from

$87.19
Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:
  • (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
  • Shank O.D. .540″
  • Includes Locks and Hex Wrench
  • High-Quality Grade Steel
  • Heat-Treated For Ex Strength
  • Plated With Durable Gold Tone Finish
See More

Edelbrock – Intake Manifold replacement top gasket (Part No.6988)

Intake Manifold replacement top gasket

from

$24.99
Product Features:
  • Replacement Gasket For PN[7070] Edelbrock Intake
  • One Gasket Only
See More

B & M – Torque Converter, Holeshot 3000 (Part No.70421)

Torque Converter, Holeshot 3000

from

$789.99
The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

In-Demand Performance Fuel Systems for 1984 Chevrolet Caprices

Select from 15 premium Performance Fuel Systems parts for your 1984 Chevrolet Caprice, with prices ranging from $12.99 to $541.99.

Mr. Gasket – Fuel Pump Block-Off Plate (Part No.1515)

Fuel Pump Block-Off Plate

from

$12.99
This is what you need when changing your manual fuel pump to electric. It blocks the hole that remains when you remove the mechanical fuel pump from the engine to keep the oil inside. This plate is precision machined and is chrome plated.

Product Features:
  • Chrome Plated Steel
  • Comes With Gasket
See More

Edelbrock – Performer 1404 Carburetor: 500 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1404)

Performer 1404 Carburetor: 500 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$435.99
The Edelbrock 1404 Performer Series 500 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – CARBURETOR (Part No.14054)

CARBURETOR

from

$488.99
Product Features:
  • EnduraShine Finish
  • GM/AMC-Style Throttle Linkage
  • Can Add Electric Choke PN[1478]
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$428.99
The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)

Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$451.99
The Edelbrock 1407 Performer Series 750 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Holley – High Output Mechanical Fuel Pump – 110 GPH Free Flow (Part No.12-327-11)

High Output Mechanical Fuel Pump - 110 GPH Free Flow

from

$144.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:
  • High Output Fuel Flow
  • Flows 110 gph Free Flow
  • Shutoff Pressure Pre-Set From 6.5 To 8 PSI
  • Fuel Pressure Regulator Is Not Required
  • Heavy Duty Construction For Continuous High rpm Operation
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • Inlet And Outlet Tapped For 3/8 in. NPT
  • Inlet/Outlet Tapped For 3/8 in. NPT
See More

Holley – High-Flow Mechanical Fuel Pump for Street Performance (Part No.12-834)

High-Flow Mechanical Fuel Pump for Street Performance

from

$124.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:
  • Street Performance
  • Flows 80 gph Free Flow
  • Shutoff Pressure Pre-Set 7.5 PSI
  • Fuel Pressure Regulator Is Not Required
  • Heavy Duty Construction For Continuous High rpm Operation
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • Inlet And Outlet Tapped For 1/4 in. NPT
  • Inlet/Outlet Tapped For .25 in. NPT
See More

Spectre – Sbc Blk Off Plate W/Bolts (Part No.42463)

Sbc Blk Off Plate W/Bolts

from

$12.99
Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.

Product Features:
  • Necessary if switching to electric fuel pump
  • Includes block off plate gasket
  • Includes chrome mounting bolts with washers
  • Triple chrome plated
See More

Holley – Mechanical Fuel Pump (Part No.12-327-13)

Mechanical Fuel Pump

from

$165.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:
  • High Output Fuel Flow
  • Flows 130 gph Free Flow
  • Shutoff Pressure Pre-Set From 7.5 To 9 PSI
  • Fuel Pressure Regulator Required Recommend P/N 12-704
  • Heavy Duty Construction For Continuous High rpm Operation
  • Redesigned High Flow Valves Ensure Adequate Fuel Delivery
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • Inlet And Outlet Tapped For 3/8 in. NPT
See More

Mr. Gasket – Fuel Pump Mounting Plate (Part No.1514)

Fuel Pump Mounting Plate

from

$16.99
Ideal for mounting a stock original equipment pump. The mounting plate is precision cut to cover the stock fuel pump opening and is complete with gasket.

Product Features:
  • Chrome Plated Steel
  • Comes With Gasket
See More

Edelbrock – CARBURETOR (Part No.14064)

CARBURETOR

from

$541.99
Product Features:
  • EnduraShine Finish
  • GM/AMC-Style Throttle Linkage
  • Electric Choke Installed from Factory
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Reman Thunder AVS Carb #18129 800 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.18129)

Reman Thunder AVS Carb #18129 800 CFM With Manual Choke, Satin Finish (Non-EGR)

from

$413.99
Product Features:
  • Satin Finish
  • 4 Barrel
  • Aluminum Body Material
  • Manual Choke Type
  • 800 cfm Maximum Flow Rating
See More

Edelbrock – Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9907)

Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR)

from

$407.99
Product Features:
  • Satin Finish
  • 4 Barrel
  • Annular Booster Type
  • Manual Choke Type
  • 750 cfm Maximum Flow Rating
See More

Holley – Keith Dorton Series; VoluMax Race Series Fuel Pump (Part No.12-327-20)

Keith Dorton Series; VoluMax Race Series Fuel Pump

from

$206.99
Keith Dorton Series VoluMax race series fuel pump made from heavy duty construction for continuous high RPM operation. Redesigned high flow valves always ensure adequate fuel delivery. Fuel pressure regulator is required. Fuel body casting can be rotated

Product Features:
  • High Output Fuel Flow
  • Flows 170 gph Free Flow
  • Shutoff Pressure Pre-Set At 8 PSI
  • Fuel Pressure Regulator Required Recommend P/N 12-704
  • Heavy Duty Construction For Continuous High rpm Operation
  • Redesigned High Flow Valves Ensure Adequate Fuel Delivery
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • 3/4in.-16 Inlet And Outlet Ports
See More

Most Sold 1984 Chevrolet Caprice Performance Exhaust Products

Explore our best-selling Chevrolet parts for the 1984 Caprice among 20 OEM and aftermarket options starting from $20.99.

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1444)

Exhaust Manifold Gasket Set

from

$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Hooker Headers – Competition Header (Part No.2466HKR)

Competition Header

from

$269.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Flowtech – Real-Seal; Header Gasket (Part No.99150AFLT)

Real-Seal; Header Gasket

from

$85.39


Product Features:
  • Water/Weather Resistant
  • Re-Useable
  • Will Not Burn Or Blow Out
  • Suitable For Port-Matching
  • Made In USA
See More

Mr. Gasket – Performance Exhaust Gasket Set for Enhanced Sealing and Durability (Part No.150B)

Performance Exhaust Gasket Set for Enhanced Sealing and Durability

from

$20.99
Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.

Product Features:
  • Manufactured from high-temperature acrylic blend exhaust material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
  • Resists Deteriorating
  • Provides Excellent Torque Retention
See More

Flowtech – Standard Header with Enhanced Fuel Efficiency and Leakproof Technology (Part No.11108FLT)

Standard Header with Enhanced Fuel Efficiency and Leakproof Technology

from

$223.99


Product Features:
  • Fuel Economy From The Engine
  • Leak Test For Max Performance
  • Mandrel-Formed Power Plenum
  • Leakproof O-Ringed Port Seals
  • Include All Mounting Hardware
See More

Mr. Gasket – Aluminum Exhaust Gaskets for Intense Heat Resistance (Part No.7402G)

Aluminum Exhaust Gaskets for Intense Heat Resistance

from

$42.99
Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.

Product Features:
  • Withstands Intense Exhaust Heat
  • Reusable header, exhaust manifold and collector flange gaskets
  • Manufactured from “dead soft” aluminum layers – .125″ thick
  • Easy Removal For Disassembly
  • Conforms easily to surface irregularities (warped flanges)
  • Compresses down to 0.060″ to create a tight leak-proof seal
  • Will not shrink, deteriorate, or blow out- eliminating gasket leaks
  • For high performance street, drag race and oval track use
See More

Hooker Headers – High-Performance Small Block Chevy Long Tube Headers (Part No.2451HKR)

High-Performance Small Block Chevy Long Tube Headers

from

$283.99
Small block Chevy 350 applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Flowmaster Inc. – 40 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Aggressive Sound (Part No.942041)

40 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Aggressive Sound

from

$133.99
This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Flowtech – High-Performance Headers with Fuel Economy and Leakproof Design (Part No.11100FLT)

High-Performance Headers with Fuel Economy and Leakproof Design

from

$227.99


Product Features:
  • Fuel Economy From The Engine
  • Leak Test For Max Performance
  • Mandrel-Formed Power Plenum
  • Leakproof O-Ringed Port Seals
  • Include All Mounting Hardware
See More

Hooker Headers – Competition Header (Part No.2451-1HKR)

Competition Header

from

$619.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Mr. Gasket – Aluminum Exhaust Gasket: High-Heat Resistant, Easy Removal (Part No.7401G)

Aluminum Exhaust Gasket: High-Heat Resistant, Easy Removal

from

$42.99
Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.

Product Features:
  • Withstands Intense Exhaust Heat
  • Reusable header, exhaust manifold and collector flange gaskets
  • Resists Deteriorating
  • Manufactured from “dead soft” aluminum layers – .125″ thick
  • Easy Removal For Disassembly
  • Conforms easily to surface irregularities (warped flanges)
  • Compresses down to 0.060″ to create a tight leak-proof seal
  • Will not shrink, deteriorate, or blow out- eliminating gasket leaks
  • For high performance street, drag race and oval track use
See More

Mr. Gasket – Exhaust Gasket Set (Part No.150)

Exhaust Gasket Set

from

$30.19
Manufactured from high-temperature composite exhaust material. Provides maximum torque retention to eliminate gasket failure. Can be trimmed if necessary for modified port applications. Precision die cut for an excellent fit. For OE replacement, high-performance street, drag race and oval track.

Product Features:
  • High-Temperature Exhaust Material
  • Withstands Extreme Exhaust Heat
  • Provides Excellent Sealing And Durability
  • Superior Tensile Strength
  • Resists Deteriorating
  • Provides Excellent Torque Retention
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1402)

Exhaust Manifold Gasket Set

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Exhaust Manifold Gasket Set for Chevrolet (Part No.7204)

Exhaust Manifold Gasket Set for Chevrolet

from

$24.99
Product Features:
  • 0.0625 in. Thickness
  • 1.50 in. x 1.50 in. Port Size
  • For SB Chevy
  • Black Color
  • Two Piece Configuration
See More

Hooker Headers – Competition Header (Part No.2451-2HKR)

Competition Header

from

$895.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Hooker Headers – Competition Header (Part No.2466-1HKR)

Competition Header

from

$668.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Mr. Gasket – Copper Seal; Exhaust Gasket Set (Part No.7151)

Copper Seal; Exhaust Gasket Set

from

$60.29
Copperseal exhaust gaskets are unique gaskets made from .043 inch solid copper. They feature an embossed O-ring design for a leak proof seal. They won’t shrink, deteriorate or blowout. Header bolts stay tight. Ideal for motor homes and towing.

Product Features:
  • Will Not Shrink/Deteriorate
  • Creates A Tight Leak Proof Seal
  • Helps Lower Under hood Temps
  • Seals Irregular Surfaces
  • Seals Slightly Damaged Surface
  • Ideal For Tow Vehicles
  • Ideal For Motor Homes
See More

Mr. Gasket – Copper Seal; Exhaust Gasket Set (Part No.7150)

Copper Seal; Exhaust Gasket Set

from

$59.99
Copperseal exhaust gaskets are unique gaskets made from .043 inch solid copper. They feature an embossed O-ring design for a leak proof seal. They won’t shrink, deteriorate or blowout. Header bolts stay tight. Ideal for motor homes and towing.

Product Features:
  • Will Not Shrink/Deteriorate
  • Creates A Tight Leak Proof Seal
  • Helps Lower Under hood Temps
  • Seals Irregular Surfaces
  • Seals Slightly Damaged Surface
  • Ideal For Tow Vehicles
  • Ideal For Motor Homes
See More

Mr. Gasket – Exhsthdrgskt (Part No.7652G)

Exhsthdrgskt

from

$51.99
Header Installation Kit – Chevrolet V8 1955-1991 265-400 Oval Port. Includes gaskets and fasteners necessary for header installation. Made using premium Ultra-Seal exhaust and collector gaskets. Mr. Gasket header and collector bolts deliver necessary clamp-load to seal flange mating surfaces.

Product Features:
  • Oval Port Header Gaskets
  • Port Size 1.50″ x 1.82″
  • Collector Gasket 3.00″ Diam. 3-bolt Style
  • Includes Header & Collector Bolts
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1400)

Exhaust Manifold Gasket Set

from

$33.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Top-Rated Performance and Racing Products Brands For Your 1984 Chevrolet Caprice

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1984 Chevrolet Caprices. Below you’ll find some of our best rated Performance and Racing Products from K&N, Mr. Gasket, and Edelbrock, and more. Performance and Racing Products from these brands that fit a 1984 Caprice start at just $9.99 and are rated as high as 5 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular K&N 1984 Chevrolet Caprice Performance and Racing Products

When it comes to maintaining or upgrading your 1984 Chevrolet Caprice, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. K&N ticks all of those boxes. We offer a wide selection of K&N Performance and Racing Products, specifically designed for the 1984 Chevrolet Caprice. With over 1 K&N brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $17.99. Plus, with over 35 customer reviews and an average rating of 5 stars, you can trust that our K&N Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

Popular Mr. Gasket 1984 Chevrolet Caprice Performance and Racing Products

Mr. Gasket auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1984 Chevrolet Caprice owner should feel confident when installing genuine Mr. Gasket parts in their vehicle. To ensure the best fit and performance for your 1984 Caprice, Advance Auto Parts carries a full inventory of 44 Mr. Gasket Performance and Racing Products. Plus you will be keeping your Chevrolet in peak condition while saving money because prices on these Mr. Gasket Performance and Racing Products range from $9.99 to $499.99, plus, with more than 50 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

Distributor Hold-Down Clamp
from
$9.99
This product is not rated

Distributor Hold-Down Clamp

“”

Oil Pan Bolt Kit
from
$17.49
This product is not rated

Oil Pan Bolt Kit

“”

Aluminum Exhaust Gasket: High-Heat Resistant, Easy Removal
from
$42.99
This product is not rated

Aluminum Exhaust Gasket: High-Heat Resistant, Easy Removal

“”

FAQs for 1984 Chevrolet Caprice Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1984 Chevrolet Caprices?

Out of 241 Performance and Racing Products that fit 1984 Chevrolet Caprices, the following parts are the top sellers:

What’s the price range for 1984 Chevrolet Caprice Performance and Racing Products?

Performance and Racing Product prices for the 1984 Chevrolet Caprice start at $9.99 and go up to $1,138.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1984 Chevrolet Caprice?

The average price for Performance and Racing Products for the 1984 Chevrolet Caprice is $236.29. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Chevrolet Caprice model years?

Yes, we currently carry Performance and Racing Products for 34 model years of Chevrolet Caprices between 1966 and 2017. Performance and Racing Products are bought most frequently for the following model years: 2017, 2016, 2015, 2014, 1996, 1995, 1994, 1993, and 1992.

What are the cheapest Performance and Racing Products for my 1984 Chevrolet Caprice?

The cheapest 1984 Chevrolet Caprice Performance and Racing Products we carry in stock are:

What are the top-rated Performance and Racing Products that fit the 1984 Chevrolet Caprice?

Out of 768 reviews by customers, our 1984 Chevrolet Caprice Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1984 Chevrolet Caprice and their top-rated products:

  • Racing Pulleys
    • Pulley (22905645) – $49.99
  • Performance Suspension Products
    • Pulley (22905645) – $49.99

What types of Performance and Racing Products do you sell for my 1984 Chevrolet Caprice?

Can I get help with 1984 Chevrolet Caprice Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Chevrolet Performance and Racing Products and more.

What is your return policy for Chevrolet Caprice Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Chevrolet Caprice Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.