Name: Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Brand: FEL-PRO Performance
SKU: 1025
Price: 72.99 USD

from

$72.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$116.99

Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.

Product Features:

Assures Longer Lasting Cab to Bed Alignment
Replace to Restore Ride Height
Gain Durability
Stronger Than Original Rubber Mounts

from

$641.99

Power Train

from

$394.99

The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$443.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

7 in. Diameter
Absolutely the most accurate way to trigger the ignition.
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.

from

$56.39

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

Helically wound conductor suppresses electro and radio noise
Kevlar core combination for great strength and durability
Heavy Duty Terminals For Secure Connection
8mm silicone and synthetic jacket resists heat and abrasion
500 Ohms/ft. Resistance For Improved Spark Delivery And Power
Silicone Boots Protect Against High Exhaust Temps

from

$366.99

Designed to fit Hooker Competition header, Manifold or catalytic converter back applications. Cat-back kits install behind the converter and all other applicable emission control devices.

Product Features:

Reducer Flex-Tubes
Reduces Backpressure
Hardware Included
Instructions Included

from

$25.99

Manufactured from high-density cork /rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For original equipment replacement and high performance street.

Product Features:

Manufactured from high-density cork /rubber blend gasket material
Provides excellent sealing and durability
Complete with molded rubber front/rear oil pan end seals where applicable
For OE replacement and high performance street use

from

$48.49

This unit permits a seamless wide range of adjustment to both amount and rate of ignition advance. This unit helps increase horsepower and throttle response. It provides maximum spark advance while preventing detonation or “pinging”. This kit includes an allen wrench for easy adjustment along with instructions.

Product Features:

Adjustable Vacuum Advance
Increases Horsepower And Throttle Response
Includes Allen Wrench For Adjustments
Instantly Increase Horsepower
Maximum Possible Spark Advance
Not Legal For Sale/Use In CA

from

$587.99

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:

Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
Best with aftermarket converters and more rear gear.
Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

from

$23.79

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

Fits Chevy engines
Includes a 1/2 inch NPT threaded hole for by-pass hose
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$37.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$544.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, new turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$126.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
O.D.: 1.254″, I.D.: .880″
Single valve springs with damper
Approximately .490″ max lift at recommended installed height

from

$168.89

Hypertech ThermoMaster Power Chips are engineered for stock 1995-1981 GM vehicles (premium octane fuel required). The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. ThermoMaster Power Chips are designed for daily street driving or competition in unmodified vehicles using a 160 Deg. or 180 Deg. thermostat. Hypertech Power Chips(TM) are emissions certified 50-state legal (application specific).

Product Features:

Use w/Low-Temp 160-180 Deg. PowerStat Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$11.99

Energy Suspension performance bump stops help cushion a collapsing suspension, preventing bottoming-out and expensive vehicle damage. Hyper-Flex performance polyurethane bump stops for control arms, traction bars, leaf springs, etc. are guaranteed to last longer and operate more efficiently than original rubber stops. The smaller, general purpose bullet shaped snubber is ideal for control arms. the low profile button head is for use when clearance is limited. Our large competition race style bump stops smooth out compression better and have a large reinforced metal plate welded to the mounting plate and molded-in. Each style is specially designed for a perfect and custom fit and each style has it’s own durometer, hardness, characteristics. Energy’s wide selection of bump stops are available in red or black color.

Product Features:

Made of Superior Hyper-Flex+ Material
Helps Prevent Damage to Control Arm

from

$59.99

Spectre’s Chrome GM Differential Covers feature a 14 bolt design and include the chrome bolts and gasket needed for an easy install. Made to OEM specifications these differential covers are triple chrome plated ensuring they perform as well as they look. This product fits the following vehicles with a 9.5 inch ring gear: 1981 and up Chevy/GMC (rear), 1973-1995 Chevy/GMC 3/4 ton-1 ton 2/4 wheel drive (rear). Includes 14 SAE standard chrome bolts for installation. You’ll need to supply your own bolts if your application requires metric bolts.

Product Features:

Fits the following vehicles with 9.5″ ring gear: ’81-up Chevy/GMC (rear), ’73-’95 Chevy/GMC 3/4-1 ton 2/4WD (rear)
Triple chrome plated
14 bolt design cover
14 chrome 5/16 inch -18 x 3/4 inch differential cover bolts included

from

$100.99

Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:

10-15% More Energy
Direct Plug In Replacement Direct OE Fit
Advanced Bobbin Technology
Highly Specialized Silicone Magnetic Steel Cores
Standard Motor Products SMP Dr-31
MSD 8225

from

$60.99

ACCEL cap and rotor kits offer superior protection from “arc-thru” and crossfire. Features 60k V-rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts and steel rotor springs provide for high spark energy flow.

Product Features:

See catalog for application information
Features 60K V Rated Alkyd Compound

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

from

$824.99

Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

Long Tube Lengths
Long Transition Collectors
Monstrous Low-Mid Range Torque
Keep Top End Horsepower
Provides Finest Fit
Most Durable Design Available

from

$158.89

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

Designed For Daily Street Driving
For Unmodified Vehicles w/Stock Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes

from

$165.99

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

High Output Fuel Flow
Flows 130 gph Free Flow
Shutoff Pressure Pre-Set From 7.5 To 9 PSI
Fuel Pressure Regulator Required Recommend P/N 12-704
Heavy Duty Construction For Continuous High rpm Operation
Redesigned High Flow Valves Ensure Adequate Fuel Delivery
Fuel Body Casting Can Be Rotated For Plumbing Situations
Inlet And Outlet Tapped For 3/8 in. NPT

from

$30.19

With the introduction of our 20 Amp extreme HEI module, we needed an HEI cap and rotor that could withstand the high output. The answer was to mold our own HEI cap, rotor and coil cover. The cap and rotor will fit our HEI Pro-Billet distributor, PN 8365, plus will work on stock applications.

Product Features:

Extreme output rotor

from

$16.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for repair applications
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$74.99

Adds a dramatic amount of performance and durability to any vehicle, cars, trucks and SUVs. Helps the vehicle be in control – when maneuvering through turns, during standing start accelerations, braking, even over bumps and berms. Made of Energy’s Hyper-Flex performance polyurethane which lasts 5 -10 times longer than conventional rubber components.

Product Features:

Made of Superior Hyper-Flex+ Material
Adds Dramatic Amount of Performance/Durability
Helps Vehicle Be in Control
Allows the Suspension to Function Properly

from

$157.99

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features: