1983 GMC C3500 Differentials

14T cover gasket.

Product Features:

• Cover gasket
• Fits GM 10.5″ 14 bolt truck

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1988 and down GM 10.5″ 14 bolt truck
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Axle shaft damaged or bearings worn out. This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

• Fits GM 10.5″ 14 bolt truck
• 4.10 ratio and down only
• Clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Product Features:

• DANA-70 R/P 4.10 STD MG 72154-5X .625″ OFFSET

Product Features:

• Carrier shim kit
• Fits Dana Spicer 70 and 70HD

DiffrlPinSupportBolt

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

10.5″ GM 14 bolt truck crush sleeve, 1989 & newer. Approx 0.920″ long.

Product Features:

• Crush sleeve for 1989 and up GM 10.5″ 14 bolt truck
• 0.920″ tall

Yukon mini spool for GM 10.5″ 14 bolt truck.

Product Features:

• Fits 10.5″ GM 14 bolt truck
• Provides 100% traction to both wheels at all times
• Installs into standard open carrier case

Yukon 1480 Lifetime Series U/Joint. 4.188″ snap ring span, 1.375″ cap diameter. Outside snap ring.

Product Features:

• Clutch kit
• Fits GM 10.5″ 14 bolt truck with Eaton positraction
• Carbon fiber clutches

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

aFe Power’s new rear differential cover brings performance engineering to the protection of your axle’s differential. This differential cover is constructed out of durable A356-T6 cast aluminum with reinforcing ribs for maximum strength. Mounting hardware is included for a hassle-free installation. An oil level sight glass and calibration plug set to the factory level prevents overfilling of the differential. A magnetic drain plug and a deep reach magnetic fill plug are provided for maximum protection. This cover is finished in black powder-coating with machined fins for a distinctive look. 4 Quart Gear Oil Capacity: This cover has about a 4 quart gear oil capacity at the factory fill level, factory cover holds about 3 quarts. Built-in External Fins: Built-in external fins transfer heat from the fluid to the outside air for maximum cooling. Magnetic Drain/Fill Plug: This system incorporates a magnetic drain and deep reach fill plug that captures loose particles for maximum rear-end protection. Oil Level Sight Glass: Large oil level sight glass with 1/8” NPT calibration plug set to the factory fluid level to eliminate overfilling. When it comes to engineering for power, performance, protection and value, aFe Power is the only choice.

Product Features:

• Constructed of Durable A356 Die Cast Aluminum
• Reinforcing Ribs and Black Powder coating w/Machined Fins
• Magnetic Drain and Fill Plugs Capture Loose Particles
• Large Oil Level Sight Glass w/ Calibration Plug

Product Features:

• KIT SHIM SIDE 9.5″ GM

Replacement pinion nut for Dana 44 JK, 44HD, 60, 70, 70U, 70HD & Nissan Titan rear. 1 5/16″ nut, 7/8″ x 14 thread.

Product Features:

• Pinion nut for Jeep JK rear, Dana Spicer 44HD, 60, 70, 70U, 70HD and Nissan Titan rear
• 7/8″ x 14 thread
• 1 5/16″ socket

Yukon replacement standard open spider gear kit for Dana 80 with 37 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 80 open differential with 37 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Product Features:

• GM10.5″ 14 BOLT OPEN EMPTY CASE 4:10 & DWN

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

• Cross pin shaft
• Fits Dana Spicer 60 and 70
• Powr Lok positraction only

Set-up carrier bearing kti (2 bearings, no races) for Dana 70 HD and Dana 80. 469. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 80
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

Product Features:

• Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

Valvoline High Performance Gear Oil is an extreme pressure gear lubricant formulated with quality base oils and superior additives that helps protect against severe temperatures, shock loads, scuffing, scouring, corrosion and pitting in high speed, high load, high torque and high horsepower conditions.

Product Features:

• Formulated for reliable gear protection
• Protects against severe temperatures to help extend service life
• Formulated with extreme-pressure additives to minimize gear wear from shock loads
• Helps protect against gear wear from scuffing, scouring, corrosion and pitting
• Recommended for conventional hypoid differentials and non-synchronized manual transmissions in passenger cars, light trucks, sport utility vehicles, vans and heavy-duty trucks where an API-GL5 or GL-4 fluid is specified
• PLEASE NOTE: Valvoline recommends SynPower Full Synthetic Gear Oil for limited slip differentials

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

Yukon replacement yoke for Dana 80 with a 1480 U/joint size. 4.188″ snap ring span, 1.375″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 80
• 37 spline
• 1480 u-joint size
• 4.188″ snap ring span
• 1.375″ cap diameter
• Outside snap ring design
• Strap style

Product Features:

• MINI INSTALL KIT DANA 80

Product Features:

• Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
• Fits standard open differentials only

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

21 Piece bearing race driver set. (Box wt: 140lbs) No return.

Product Features:

• Bearing race driver set
• 21 pieces
• All steel construction