from

$126.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
O.D.: 1.254″, I.D.: .880″
Single valve springs with damper
Approximately .490″ max lift at recommended installed height

from

$52.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$789.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$17.79

Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$23.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$381.99

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
7.3125 in. Block To Hub Height
Satin Finish

from

$85.09

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$17.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$26.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$31.99

Edelbrock part #6998 Front Timing Cover Gasket set for Big-Block Chevy. Includes front cover gasket and front seal.

Product Features:

Includes replacement timing cover and water pump gaskets and the crank oil seal for big block Chevrolet engines
Features a tough, scuff-resistant silicone rubber coating
Helps in sealing without the engine warming up
Reduces fluid migration through the gasket
Resists fatigue

from

$23.99

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

Repairs That Leaky Rear Main Sail
Silicone Rubber to Withstand Extreme Engine Oil Temperatures
Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
Injection Molded for Precise Fit

from

$36.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.
Not intended for use in emission controlled vehicles.

from

$25.99

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes sixteen (16) 3/8 inch-16 x 1-1/4 inch bolts & washers

Product Features:

Zinc plated Grade 5 steel
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Ideal For Minimal Space
12-Point Head And Flange
Zinc Plated For Protection

from

$502.99

Product Features:

Comes with Endurashine finish that does not oxidize or fade
Manifold height is 4.3 in. in the front and 5.4 in. in the rear
Constructed from aluminum
Port dimensions are 1.70 in. high by 1.68 in. wide
Manifold has provisions for oil filler tube

from

$29.99

Product Features:

Timing Chain Only

from

$74.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$958.99

The Edelbrock #607519 Performer cylinder head is designed for 302, 327, 350 and 400 cid small-block Chevy engines up to 1986. This cylinder head includes your choice of 64cc (In order to retain stock compression ratio on 1970 and earlier small-blocks) or

Product Features:

Complete Single For Hydraulic Flat Tappet
70cc Combustion Chamber Volume
185cc Intake/65cc Exhaust Runner Volume
2.02 in. Intake/1.6 in. Exhaust Valve Diameter
0.562 in. Deck Thickness

from

$1014.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
70cc Combustion Chambers Improve Performance
Retain Stock Compression Ratio

from

$187.99

Product Features:

Case-Hardened Tubing
Surface Hardening
Welded Ends
0.3125 in. Diameter
Use with or without Hardened Steel Guideplates

from

$189.99

Product Features:

Case-Hardened Tubing
Welded Ends
5/16 in. Diameter
Use with or without Hardened Steel Guideplates

from

$40.19

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material.
Provides excellent sealing and durability.
Can be trimmed if necessary for modified port applications.
Complete with manifold end seals and distributor gasket.
For OE replacement, high performance street, drag race and oval track use.

from

$29.99

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
Complete with manifold end seals & distributor gaskets if applicable
For OE replacement, high performance street, drag race and oval track use

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$95.99

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

Valve Spring Retainers for Use OE Cast Iron Heads
Superior Quality Heat-Treated Steel
Machined for Strength with Black Oxide Finish
Finish Ensures Rust and Corrosion Protection

from

$529.99

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:

Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
Best with aftermarket converters and more rear gear.
Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

from

$542.99

HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.

Product Features:

HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.
279/296 Advertised Duration, 227/241 Duration @ .050″, .498″/.483″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

1983 Chevrolet C10 Performance Engines

More 1983 Chevrolet C10 Performance Engines

Essential 1983 Chevrolet C10 Performance Engines

Competition Cams – Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height (Part No.981-16)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1004)

B & M – Torque Converter, Holeshot 3000 (Part No.70421)

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4377)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Edelbrock – Water Pump Big-Block Chevy Standard/Long in Satin Finish (Part No.8851)

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1074)

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1803)

Edelbrock – Front Timing Cover Gasket Set #6998 For Big-Block Chevy, With Front Seal (Part No.6998)

Mr. Gasket – Rear Main Seal Gasket (Part No.1960)

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)

Mr. Gasket – Intake Manifold Bolts (Part No.957G)

Edelbrock – Performer 2-O Intake Manifold for 1965-90 Big-Block Chevy, EnduraShine Finish (Part No.21614)

Edelbrock – TIMING CHAIN (Part No.7844)

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7810)

Edelbrock – RPM Small-Block Chevy Cylinder Head SBC 70cc Flat Tappet Cam Polished (Part No.607519)

Edelbrock – RPM Small-Block Chevy Cylinder Head SBC 70cc Hydraulic Flat Tappet Cam (Part No.60759)

Edelbrock – Pushrod Set for S/B Chevy (Part No.9629)

Edelbrock – Pushrod Set for S/B Chevy (Part No.9630)

Mr. Gasket – Intake Gasket (Part No.116)

Mr. Gasket – Intake Gasket Set – Standard Duty – Big Block Chevy With Stock Rectangle Ports – 1.75"W X 2.50"H (Part No.108)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

Competition Cams – CAMSHAFT, SBC 295 BIG MUTHA THUMPR HYDRAULIC 1 EA (Part No.12-602-4)

Competition Cams – Thumpr 227/241 Hydraulic Flat Cam (Part No.11-600-4)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Popular 1983 Chevrolet C10 Performance Engines Categories

1983 Chevrolet C10 Performance Engines

Performance Engines Brands To Make Your 1983 Chevrolet C10 Last

Popular B & M Performance Engines

Top 1983 Chevrolet C10 Performance Engines from Mr. Gasket

FAQs for 1983 Chevrolet C10 Performance Engines

What are the most purchased Performance Engines for the 1983 Chevrolet C10?

What are the top-rated 1983 Chevrolet C10 Performance Engines?

More Popular Parts for All Makes