1982 Pontiac Firebird Differentials

7.5 & 7.625 Standard Open Pinion gear Thrust Washer.

Product Features:

• Pinion gear thrust washer for GM 7.5″ and 7.625″
• Fits standard open differentials only

Yukon 1541H alloy rear axle for ’82-’89 GM 7.5″ Camaro (drum brakes) with a length of 30-5/16 inches and 26 splines. 2.775″ hub. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

• 26 spline
• 30 5/16″ long
• Fits GM 7.5″ in 1982-1989 Camaro
• Drum brakes only

Product Features:

• Positraction spring kit
• Fits GM 7.5″ and 7.625″ Dura Grip
• Includes preload plates

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. Includes Supershims.

Product Features:

• Fits 1982-1999 GM 7.5″ and 7.625″
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

Motive Gear Mini-Spools replace your stock spider and side gears with a solid billet mini-spool for 100% traction to both wheels. Not recommended for street applications.

Product Features:

• Billet construction
• Not recommended for street applications
• GM7.5″ MINI SPOOL 26 SPLINE

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

High-quality Differential Carrier Shim Kit

Product Features:

• CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

Product Features:

• Shim kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction

Positraction cross pin bolt for GM 12P and 12T.

Product Features:

• Cross pin bolt for GM 12 bolt passenger car and truck
• For OEM positraction applications only

Product Features:

• Pinion depth shims for GM 7.5″, 7.625″, 7.6 IFS, 7.6 IRS, 7.75″, 8.2″, 1955-1964 passenger car and 12 bolt car and truck

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Pinion nut for GM 12 bolt car & truck, 55-62 car & truck, 8.2″, 8.2″ Buick/Olds/Pontiac & 63-79 Corvette. 1 1/8″ socket, 7/8″ x 16 thread.

Product Features:

• Pinion nut for GM 12 bolt car and truck, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and 1963-1979 Corvette
• 7/8″ x 16 thread
• 1 1/8″ socket

Product Features:

• Clutch guide
• Fits GM 7.5″ and 7.625″ Dura Grip

Yukon yoke for GM 12 bolt car & truck, 1310 u/joint size, u-bolt design. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 12 bolt passenger car and truck
• 30 spline
• 1310 u-joint size
• 3.219″ snap ring span
• 1.062″ cap diameter
• Outside snap ring design
• U-bolt style

8.5″ GM standard Open case, 2.73 & up, 28 or 30 spline.

Product Features:

• Standard open carrier case
• Fits GM 8.5″ with 28 or 30 spline axles
• 2.73 and up ratio only
• Does not include spider gears

Product Features:

• MINI SPOOL GM12 BOLT CAR & TRUCK STRANGE # 088430

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Pinion seal for GM 8.5″, 8.2″, Buick, Oldsmobile, and Pontiac.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits GM 8.5″ rear, 8.2″ and 8.2″ in Buick, Oldsmobile and Pontiac

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (Includes Supershims).

Product Features:

• Fits GM 12 bolt passenger car
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1981 and down GM 7.5″
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

M802048 set-up bearing (one bearing). No return.

Product Features:

• Set up bearing
• Fits M802048 pinion bearing
• Easily slips on and off pinion journal to allow for easier pinion depth adjustment

Differential Cover B

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM88610 race
• All steel construction

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M88010 race
• All steel construction