1982 Lincoln Town Car Performance and Racing Products
Find Your Specific 1982 Lincoln Town Car Performance and Racing Products
Below you will find various in-demand Lincoln Performance and Racing Products, components and accessories for your 1982 Town Car. Advance Auto Parts has popular Town Car parts like Performance Ignition Products, Performance Engines, Performance Distributors and more. You’ll also find aftermarket and OEM Performance and Racing Products for other Town Car model years including
2003,
2004,
2005,
2006,
2007,
2008,
2009,
2010,
2011 and more. Select a category of 1982 Lincoln Town Car Performance and Racing Products below and start saving instantly.
Popular 1982 Lincoln Town Car Performance and Racing Products Categories
Essential Performance and Racing Products for 1982 Lincoln Town Cars
B & M – CONVERTER AOD HP (Part No.40437)
from
$366.99
A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.
Product Features:
See More
Product Features:
- New Precision Pump Drive Tube
- Pressure Tested
- Fully Balanced
- Needle Thrust Bearing
- New Thrust Washer
- Washer Between Turbine and Cover
Accel – Ford 1984-98 Eec-Iv Supercoil (Part No.140012)
from
$86.99
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, and crisper throttle response. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.
Product Features:
See More
Product Features:
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Standard Motor Products SMP Fd-478
- MSD 5527
- Standard Motor Products SMP Fd-478
- MSD 5527
- Resists Shock And Vibration
- Resists Corrosion
MSD Ignition – Starter (Part No.5090)
from
$488.99
Our DynaForce starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The DynaForce starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.
Product Features:
See More
Product Features:
- 3/4″ Depth and can be used on 157 and 164 Tooth Flywheels
- Downsized design helps clearance issues w/oil pans and exhaust
- Ball bearing supported armature and pinion gear
- 3 Hp Motor Provides Power For High Compression Engines
- Gear reduction of 4.4:1 improves torque for great cranking
- Downsized design helps clearance issues
- Mount can be clocked to assist in mounting
Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)
from
$249.99
The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.
Product Features:
See More
Product Features:
- Cost effective aluminum construction provides superior strength to weight ratio
- Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
- Durable design increases valve lift while withstanding the rigors of moderate race use
- Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.
Mr. Gasket – High Performance Thermostat (Part No.4365)
from
$32.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 195 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Mr. Gasket – Intake Manifold Bolts (Part No.958G)
from
$23.79
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers
Product Features:
See More
Product Features:
- Hex Head
- Zinc Plated
- Ideal For Minimal Space
- 12-Point Head And Flange
- Zinc Plated For Protection
Mr. Gasket – Thermocap Radiator Cap (Part No.2471S)
from
$53.99
Knowing your coolant temperature can help to prevent burn injuries. Thermocap Cap, with its built-in calibrated thermometer, indicates the coolant temperature. This is useful information prior to cap removal. Never attempt to remove Thermocap Cap when the coolant temperature is very hot. The escaping hot coolant and steam may burn you. Reclamation valve works great with your coolant recovery system. Your radiator can reclaim coolant from your overflow bottle. Wide 30 degree to 270 degree F temperature range. Calibrated in centigrade and Fahrenheit. Color-coded temperature ranges.
Product Features:
See More
Product Features:
- Indicates Coolant Temperature
- Helps to Prevent Injuries from coolant or steam burns
- Integrated Coolant Reclamation Valve
- Improves Underhood Appearance
- Fahrenheit and centigrade readings
- Various valve pressures available
Edelbrock – Performer Intake Manifold Small-Block Ford (Part No.3721)
from
$414.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Competition Cams – Magnum 244/244 Hydraulic Flat Cam (Part No.31-330-3)
from
$267.99
An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.
Product Features:
See More
Product Features:
- Best with aftermarket torque converters and 9.5:1 compression.
- Great high RPM power.
- Easy on valve train parts.
- Can be used with mild ratio rocker arms and traditional performance valve springs.
MSD Ignition – Distributor Cap; Ford HEI; Black (Part No.84083)
from
$67.99
All the quality and performance you’ve come to expect from MSD is now available in black. Our customers have requested black parts for their builds so we’ve answered with the addition of several black distributor caps and cap and rotor kits. The black parts are built to the exact specifications of the traditional MSD red components. If you’re looking to change up the look under the hood of your street machine, off-road rig or race car; check out the complete line of MSD black components.
Product Features:
See More
Product Features:
- Injection Molded From DuPont Rynite Material
- Extreme strength; high dielectric properties
- Designed with performance in mind
- High quality; voltage insulating material
- Brass terminals
- Black in color
Mallory – Unilite Ignition Module (Part No.605)
from
$95.99
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
B & M – Transmission Shift Kit (Part No.40227)
from
$213.99
Transpak – Ford, Lincoln, Mercury – 1980 to 1992 AOD (excludes 1992 and later with electronic shift). Recalibrate your automatic transmission for optimum performance. Select the mode that best suits your application. Improves transmission life. Transmission removal not required. The next step up from the Shift Improver Kit is the Transpak. It has all the features in the Shift Improver Kit plus it provides additional driver manual control (GM TH-400, 350, Ford C-6 and Chrysler Torqueflite only). Most stock automatic transmissions won’t downshift into low gear above 15 mph, and automatically upshift at a predetermined speed no matter what gear you’re in. With the Transpak, you can downshift at any speed, and you can hold the transmission in first gear to any speed that you want! This is an asset when you’ve got a modified engine, and you want additional RPMs, or you’re towing a trailer or driving heavy loads downhill. Stage 1 Heavy Duty – For street rods, normal passenger vehicles or other heavy duty use. Firmer shift feel but not harsh. Improves transmission performance and life dramatically without loss of comfort. Normal automatic operation when in Drive. Stage 2 Hi-Performance Street – For full performance street use. Essentially the same as Heavy Duty mode except shift is much quicker. Retain full automatic features and standard shift points with selector in Drive.
Product Features:
See More
Product Features:
- Recalibrate Auto. Transmission
- Optimum Performance
- Select Your App. Mode
- Improves Transmission Life
- Trans. Removal Not Required
- Downshift At Any Speed
- Great For Trailer Towing
- For Heavy Loads Driving Downhill
Edelbrock – Water Pump for Small-Block Ford 351W in Black Finish (Part No.88433)
from
$376.99
Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool
Product Features:
See More
Product Features:
- Standard Impeller Rotation
- 0.625 in. Pilot Shaft
- 0.750 in. Ball/Ball Bearing
- 5.70 in. Block To Hub Height
- Black Finish
B & M – Automatic Shifter – Megashifter – Universal (Part No.80690)
from
$539.99
The Classic BAndM Megashifter features a Ratcheting action, ensuring positive shifts. Chrome Knob, Neutral safety switch And NHRA/IHRA Approved reverse lockout. Fits Most 3 And 4 speeds.
Product Features:
See More
Product Features:
- Universal Floor Mount
- Base Can Be Trimmed-Custom Fit
- Cable Operated
- Quick Installation
- Accurate Shifting
Edelbrock – Torker-Plus Camshaft Kit for 1957-95 Small-Block Ford 289-302 V8 (Part No.5022)
from
$440.99
Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.
Product Features:
See More
Product Features:
- Designed for 2500 to 6500 Performance
- Designed for Hi-Perf Street; Drag or Marine Use
- Matched to Edelbrock Torker II Intakes
- Includes Hydraulic Lifters and Assembly Lube
- Dyno Matched/Street Proven Performance
- Take The Guesswork Out Of Camshaft Selection
MSD Ignition – Rotor Assembly; Chevy V8 Cap-A-Dapt (Part No.8421)
from
$67.99
MSD Ignition is a company built on Customer Satisfaction and Service. That is why all of MSD products go through regimented test procedures before they are ever packaged and shipped. MSD stands behind its products for one full year after purchase
Product Features:
See More
Product Features:
- Rotor phasing can be adjusted.
- Ideal When Atomic TBI Is Controlling The Timing
Competition Cams – VALVE SEALS, 11/32" TEFLON 1 ST (Part No.503-16)
from
$223.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.
Product Features:
See More
Product Features:
- Work with .530″ guides and 11/32″ valve stem diameter
- Valve stem oil seals keep unwanted oil from entering the combustion chamber
- Several different types of valve seals are offered
MSD Ignition – Distributor Cap and Rotor Kit; MSD/Ford V8; 85-95 (Part No.8482)
from
$58.99
The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.
Product Features:
See More
Product Features:
- Rynite Injection Molded Caps And Retainers
- Designed w/Performance In Mind
- High Quality; Voltage Insulating Material
- Stainless Terminals
Edelbrock – Pushrod Set for Small Block Ford 289-302 (Part No.9632)
from
$221.99
Product Features:
See More
- Case-Hardened Tubing
- Surface Hardening
- Welded Ends
- 0.3125 in. Diameter
- Use with or without Hardened Steel Guideplates
Competition Cams – XE Computer Controlled 216/224 Hydraulic Roller Cam and Lifter Kit (Part No.CL35-514-8)
from
$867.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.
Product Features:
See More
Product Features:
- Excellent performance in street fuel injected applications.
- More vacuum allows an increase in duration for improved performance and assists power brakes.
- Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
- Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1467)
from
$45.99
Product Features:
See More
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Hays – Flywheels (Part No.12-535)
from
$511.99
Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.
Product Features:
See More
Product Features:
- Certified Billet Material
- Borg and Beck Clutch Pattern
- Long-Style Clutch Pattern
- Ring Gear Securely Mounted To Prevent Spinning
Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7811)
from
$79.99Product Features:
- Solid Bushing Chain Resists Stretching
- For Use with Stock or Edelbrock Camshafts
- Stressproof Steel Crank Gears
- 3 Keyway Setting Points To Ensure Accurate Timing
- True Bearing Surface Rolls with the Sprockets
- For Engine w/ 2-piece Fuel Pump Eccentric or EFI
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1614)
from
$24.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Die cut silicone rubber gaskets conform to out-of-flat covers
- Great for on-again/off-again situations
- Not intended for use in emission controlled vehicles.
Edelbrock – Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90" (Part No.60379)
from
$1087.99
Product Features:
See More
- Capable of 300 plus horsepower when matched with the Edelbrock Performer Power Package
- 1.90 in. intake valves are for use with stock pistons
- Exhaust valve is 1.60 in.
- 60cc combustion with 170cc intake port
- Flat Tappet Camshaft Type
Upgrade your 1982 Lincoln Town Car with Top-Quality Performance and Racing Products
When it comes to maintaining or upgrading your 1982 Lincoln Town Car, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Lincoln or enhancing its overall performance, Performance and Racing Products are key to keeping your Town Car functioning at its best. At Advance Auto Parts, we offer a wide selection of 90 Performance and Racing Products for the 1982 Lincoln Town Car, designed to meet your needs without breaking the bank.
From
Performance Ignition Product
replacements to
Performance Engines
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1982 Lincoln Town Car at great prices.
Our Performance and Racing Products inventory for this model
ranges from just $7.99 to $1,087.99, with
an average price of $207.90.
Our 90 Performance and Racing Products in stock come from 12 trusted brands, so you’re sure to find the right part for your 1982 Lincoln Town Car without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1982 Lincoln Town Car, we stock popular OEM and aftermarket Performance and Racing Products from top names
like Mallory FEL-PRO Performance, and more.
Mallory Performance and Racing Products
start at just $95.99 and boast an impressive 4.9 stars average rating from customers.
With 48 customer reviews and counting, our 1982 Lincoln Town Car Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1982 Lincoln Town Car is always ready to roll. We’re committed to providing you with everything you need to keep your Town Car in top shape, all in one place.
Start shopping confidently below for your 1982 Lincoln Town Car!
Best-Selling Performance Ignition Products for 1982 Lincoln Town Cars
Enhance the driving experience in your Lincoln with 3 quality Performance Ignition Product components, starting at $34.49.
Mallory – Unilite Ignition Module (Part No.605)
from
$95.99
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)
from
$204.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).
Product Features:
See More
Product Features:
- Glass Filled Polyester Case
- Longer Spark Duration
- Increased Performance
- No Energy Loss Due To Arcing
- Includes Brass Contact Terminal
Most Popular 1982 Lincoln Town Car Performance Engines
Customize your Lincoln with 59 Performance Engines products
like Performance Engine Intake Manifold Gaskets,
Performance Intake Manifolds, and
Performance Engine Cylinder Head Gaskets, all
priced under $1,087.99.
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 11 Piece Set (Part No.1250)
from
$35.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1684)
from
$50.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Rigid core, molded silicone rubber gaskets provide for ease of installation, and are great for on-again/off-again situations (like setting valve lash).
- Features high-tech silicone material for long life, a solid steel core for strength and durability, and stainless steel compression limiters to prevent
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-1)
from
$52.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
- NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
- SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
- STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5870)
from
$42.99
Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are .187 inch thick.
Product Features:
See More
Product Features:
- Manufactured from high-density cork /rubber blend gasket material
- A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
- Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
- For OE replacement, high performance street, drag race and oval track
- .187″ thick
- Handles Ex Flange Pressure
- Forms Leak Proof Seal
- Black Latex Coating
Mr. Gasket – Water Neck (Part No.2662)
from
$23.79
Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.
Product Features:
See More
Product Features:
- Chrome Plated
- This Is A 45 Degree Neck
- Comes With O-ring And Bolts
- Has Small Hose Fitting On It
Edelbrock – Torker II 302 Intake Manifold Small-Block Ford (Part No.5021)
from
$395.99
2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Available in cast or polished.
Product Features:
See More
Product Features:
- 2500 to 6500 RPM High Performance Street Engines
- Single-Plane Low-Rise Intake Good for High RPM
- Ideal for Applications with Limited Hood Clearance
- For Top-End HP and Adequate Throttle Response
Mr. Gasket – Intake Manifold Bolts (Part No.958G)
from
$23.79
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers
Product Features:
See More
Product Features:
- Hex Head
- Zinc Plated
- Ideal For Minimal Space
- 12-Point Head And Flange
- Zinc Plated For Protection
Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)
from
$249.99
The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.
Product Features:
See More
Product Features:
- Cost effective aluminum construction provides superior strength to weight ratio
- Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
- Durable design increases valve lift while withstanding the rigors of moderate race use
- Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.
Mr. Gasket – High Performance Thermostat (Part No.4365)
from
$32.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 195 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)
from
$45.49
Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.
Product Features:
See More
Product Features:
- Heat treated black oxide coated Grade 8 alloy steel
- Thick parallel ground washer provides more accurate, uniform torque
- Hex Prevents Socket Slippage
- Accurate And Uniform Torque
- Black Plated Finish
Mr. Gasket – Valve Cover Gasket Set (Part No.276)
from
$35.99
Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Manufactured from high-density cork/rubber blend gasket material
- Provides excellent sealing and durability
- For OE replacement, high performance street, drag race and oval track use
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1614)
from
$24.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Die cut silicone rubber gaskets conform to out-of-flat covers
- Great for on-again/off-again situations
- Not intended for use in emission controlled vehicles.
Competition Cams – Valve Seals, Umbrella 11/32" 1 St (Part No.502-16)
from
$230.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.
Product Features:
See More
Product Features:
- Work with stock guides and 11/32″ valve stem diameter
- Valve stem oil seals keep unwanted oil from entering the combustion chamber
- Several different types of valve seals are offered
Competition Cams – VALVE SEALS, 11/32" TEFLON 1 ST (Part No.503-16)
from
$223.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.
Product Features:
See More
Product Features:
- Work with .530″ guides and 11/32″ valve stem diameter
- Valve stem oil seals keep unwanted oil from entering the combustion chamber
- Several different types of valve seals are offered
Edelbrock – Performer-Plus Camshaft Kit for Small-Block Ford 289-302 V8 (Part No.2122)
from
$338.99Product Features:
- Designed for Optimum Torque and Acceleration
- Maximum Performance From Idle through Mid-Range
- Matched to Edelbrock Performer Intakes
- Includes Hydraulic Lifters and Assembly Lube
- Major Improvement in Throttle Response and Torque
- Use For Daily Drivers/Trucks/Vans/RVs/4x4s
- Take The Guesswork Out Of Camshaft Selection
Edelbrock – Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90" (Part No.60379)
from
$1087.99
Product Features:
See More
- Capable of 300 plus horsepower when matched with the Edelbrock Performer Power Package
- 1.90 in. intake valves are for use with stock pistons
- Exhaust valve is 1.60 in.
- 60cc combustion with 170cc intake port
- Flat Tappet Camshaft Type
Competition Cams – XE Computer Controlled 206/212 Hydraulic Roller Cam and Lifter Kit (Part No.CL35-512-8)
from
$865.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.
Product Features:
See More
Product Features:
- Excellent performance in street fuel injected applications.
- More vacuum allows an increase in duration for improved performance and assists power brakes.
- Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
- Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
Competition Cams – ENGINE ROCKER ARM (Part No.1831-16)
from
$704.99
ENGINE ROCKER ARM
Competition Cams – ENGINE ROCKER ARM (Part No.19045-16)
from
$621.99
ENGINE ROCKER ARM
Competition Cams – Xtreme Energy Computer Controlled 206/212 Hydraulic Roller Cam (Part No.35-512-8)
from
$549.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,
Product Features:
See More
Product Features:
- Excellent performance in street carbureted applications.
- More vacuum allows an increase in duration for improved performance and assists power brakes.
- Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
- Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
Edelbrock – Victor Jr. 302 Intake Manifold Small-Block Ford (Part No.2921)
from
$474.99
Race winning design for all types of competition. Single plane maximizes torque and horsepower. Runners feature extra material for custom porting. For performance in 3500 to 7500 RPM range. For modified OE or aftermarket Windsor aluminum heads. Match with Edelbrock heads for maximum performance. Port exits can be opened to 2.10 x 1.18 inch. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.
Product Features:
See More
Product Features:
- Race Winning Design for all Types of Competition
- Single Plane Maximizes Torque and Horsepower
- Runners Feature Extra Material for Custom Porting
- For Performance in 3500 to 7500 RPM Range
- For Modified OE or Aftermarket Windsor Alum Heads
- Match with Edelbrock Heads for Max Performance
- Port Exits Can be Opened to 2.10 x 1.18 in.
Edelbrock – Torker-Plus Camshaft Kit for 1957-95 Small-Block Ford 289-302 V8 (Part No.5022)
from
$440.99
Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.
Product Features:
See More
Product Features:
- Designed for 2500 to 6500 Performance
- Designed for Hi-Perf Street; Drag or Marine Use
- Matched to Edelbrock Torker II Intakes
- Includes Hydraulic Lifters and Assembly Lube
- Dyno Matched/Street Proven Performance
- Take The Guesswork Out Of Camshaft Selection
Edelbrock – Performer Intake Manifold Small-Block Ford (Part No.3721)
from
$414.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Competition Cams – 16 Springs (Part No.26986-16)
from
$401.99
16 Springs
Top Picks for 1982 Lincoln Town Car Performance Distributors
Upgrade Lincoln Town Cars with top-quality Performance Distributors parts, including 5 OEM and aftermarket selections for your 1982 model.
MSD Ignition – Distributor Cap; Ford HEI; Black (Part No.84083)
from
$67.99
All the quality and performance you’ve come to expect from MSD is now available in black. Our customers have requested black parts for their builds so we’ve answered with the addition of several black distributor caps and cap and rotor kits. The black parts are built to the exact specifications of the traditional MSD red components. If you’re looking to change up the look under the hood of your street machine, off-road rig or race car; check out the complete line of MSD black components.
Product Features:
See More
Product Features:
- Injection Molded From DuPont Rynite Material
- Extreme strength; high dielectric properties
- Designed with performance in mind
- High quality; voltage insulating material
- Brass terminals
- Black in color
MSD Ignition – Distributor; Ford 289/302; Vacuum Advance (Part No.8479)
from
$562.99
The street pro-billet distributors are the perfect choice for powerful engines that see plenty of street time. The street models share the same features as the small diameter models shown above, plus feature a vacuum advance. This canister provides improved economy and an accurate mechanical advance lets you dial-in an advance curve to match your driving needs. A magnetic pick-up produces accurate trigger signals that remain stable throughout the entire rpm range of your engine and is completely maintenance-free.
Product Features:
See More
Product Features:
- Billet housing 5/8 in. smaller dia. than stock Ford distributors
- CARB E.O. Approved
- Easy-to-adjust mech. advance w/supplied springs and stop bushings
- Vacuum advance canister for improved economy (can be locked out)
- CNC machined billet aluminum housing and billet aluminum base
- Maintenance-free magnetic pickup and precision reluctor
- Creates stable trigger signals throughout the rpm range
- QPQ coated polished steel shaft; guided by sealed ball bearings
- Advance plate and weights are fine blanked from chrome moly steel
- QPQ coated for friction reduction
- Mech. advance assem. can be locked out for crank trigger systems
- Advance weight pins are staked and tig welded to the plate
MSD Ignition – Rotor Assembly; Chevy V8 Cap-A-Dapt (Part No.8421)
from
$67.99
MSD Ignition is a company built on Customer Satisfaction and Service. That is why all of MSD products go through regimented test procedures before they are ever packaged and shipped. MSD stands behind its products for one full year after purchase
Product Features:
See More
Product Features:
- Rotor phasing can be adjusted.
- Ideal When Atomic TBI Is Controlling The Timing
Accel – Distributor Cap And Rotor Kit (Part No.8223)
Accel – Distributor Cap And Rotor Kit (Part No.8224)
In-Demand Performance Exhaust Products for 1982 Lincoln Town Cars
Select from 5 premium Performance Exhaust Products parts for your 1982 Lincoln Town Car, with prices ranging from $39.99 to $71.99.
Mr. Gasket – Aluminum Exhaust Gasket (Part No.7410G)
from
$43.99
Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.
Product Features:
See More
Product Features:
- Reusable header, exhaust manifold and collector flange gaskets
- Manufactured from “dead soft” aluminum layers – .125″ thick
- Conforms easily to surface irregularities (warped flanges)
- Compresses down to 0.060″ to create a tight leak-proof seal
- Will not shrink, deteriorate, or blow out- eliminating gasket leaks
- For high performance street, drag race and oval track use
Mr. Gasket – Copper Seal: Exhaust Gasket Set (Part No.7160)
from
$71.99
Mr. Gasket CopperSEAL Header Gaskets are a high quality copper gasket that performs extremely well and are reusable. We recommend this in all racing and high performance applications. They are for stock heads unless indicated, and work well in high heat and turbocharged applications.
Product Features:
See More
Product Features:
- Manufactured from ¿Dead Soft¿ (solid) .043″ thick copper material
- Manufactured from ┐Dead Soft┐ (solid) .043″ thick copper material
- .051″ embossment around each exhaust port to seal irregular surfaces. Total gasket thickness .094″
- Provides excellent sealing and durability
- Conforms to and seals minor surface irregularities
- For high performance street, drag race, oval track and turbocharged (extreme heat) applications
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1467)
from
$45.99
Product Features:
See More
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1416)
from
$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1468)
from
$45.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Most Sold 1982 Lincoln Town Car Performance Transmissions
Explore our best-selling Lincoln parts for the 1982 Town Car among 1 OEM and aftermarket options starting from $213.99.
B & M – Transmission Shift Kit (Part No.40227)
from
$213.99
Transpak – Ford, Lincoln, Mercury – 1980 to 1992 AOD (excludes 1992 and later with electronic shift). Recalibrate your automatic transmission for optimum performance. Select the mode that best suits your application. Improves transmission life. Transmission removal not required. The next step up from the Shift Improver Kit is the Transpak. It has all the features in the Shift Improver Kit plus it provides additional driver manual control (GM TH-400, 350, Ford C-6 and Chrysler Torqueflite only). Most stock automatic transmissions won’t downshift into low gear above 15 mph, and automatically upshift at a predetermined speed no matter what gear you’re in. With the Transpak, you can downshift at any speed, and you can hold the transmission in first gear to any speed that you want! This is an asset when you’ve got a modified engine, and you want additional RPMs, or you’re towing a trailer or driving heavy loads downhill. Stage 1 Heavy Duty – For street rods, normal passenger vehicles or other heavy duty use. Firmer shift feel but not harsh. Improves transmission performance and life dramatically without loss of comfort. Normal automatic operation when in Drive. Stage 2 Hi-Performance Street – For full performance street use. Essentially the same as Heavy Duty mode except shift is much quicker. Retain full automatic features and standard shift points with selector in Drive.
Product Features:
See More
Product Features:
- Recalibrate Auto. Transmission
- Optimum Performance
- Select Your App. Mode
- Improves Transmission Life
- Trans. Removal Not Required
- Downshift At Any Speed
- Great For Trailer Towing
- For Heavy Loads Driving Downhill
Top-Rated Performance and Racing Products Brands For Your 1982 Lincoln Town Car
Shop for the best-rated brands offering Performance and Racing Products and other products for your 1982 Lincoln Town Cars. Below you’ll find some of our best rated Performance and Racing Products from Mallory and FEL-PRO Performance, and more. Performance and Racing Products from these brands that fit a 1982 Town Car start at just $35.99 and are rated as high as 4.9 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.
Popular Mallory 1982 Lincoln Town Car Performance and Racing Products
When it comes to maintaining or upgrading your 1982 Lincoln Town Car, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Mallory ticks all of those boxes. We offer a wide selection of Mallory Performance and Racing Products, specifically designed for the 1982 Lincoln Town Car. With over 1 Mallory brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $95.99. Plus, with over 3 customer reviews and an average rating of 4.9 stars, you can trust that our Mallory Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
from
$95.99
(3)
Unilite Ignition Module
“I like the Unilite product because it is so small and compact compared to the HEI stuff I normally use. If you are restricted on space Its a great pro”
Popular FEL-PRO Performance 1982 Lincoln Town Car Performance and Racing Products
FEL-PRO Performance auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1982 Lincoln Town Car owner should feel confident when installing genuine FEL-PRO Performance parts in their vehicle. To ensure the best fit and performance for your 1982 Town Car, Advance Auto Parts carries a full inventory of 3 FEL-PRO Performance Performance and Racing Products. Plus you will be keeping your Lincoln in peak condition while saving money because prices on these FEL-PRO Performance Performance and Racing Products range from $35.99 to $52.99, plus, with more than 7 customer reviews and an impressive 4.2 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.
from
$52.99
(2)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
“cometic head gasket is great but prob is dose not seal if the block isn’t mirror finished. many people switch over to felpro and it has worked out gre”
FAQs for 1982 Lincoln Town Car Performance and Racing Products
Which Performance and Racing Products are best-sellers for 1982 Lincoln Town Cars?
Out of 90 Performance and Racing Products that fit 1982 Lincoln Town Cars, the following parts are the top sellers:
- Lower Intake Manifold Gasket Set: 11 Piece Set (5991277) – $35.99
- Intake Manifold Bolts (17360287) – $23.79
- Aluminum Exhaust Gasket (10540505) – $43.99
What’s the price range for 1982 Lincoln Town Car Performance and Racing Products?
Performance and Racing Product prices for the 1982 Lincoln Town Car start at $7.99 and go up to $1,087.99 for the most premium parts.
What’s the average price of a Performance and Racing Product for a 1982 Lincoln Town Car?
The average price for Performance and Racing Products for the 1982 Lincoln Town Car is $207.90. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Performance and Racing Products for other Lincoln Town Car model years?
What are the cheapest Performance and Racing Products for my 1982 Lincoln Town Car?
The cheapest 1982 Lincoln Town Car Performance and Racing Products we carry in stock are:
- High Energy 6.821" Long, 5/16" Diameter Pushrod (50289666) – $7.99
- High Energy 6.881" Long, 5/16" Diameter Pushrod (50289324) – $7.99
- Flat 1 Piece Guide Plate for Ford 289-351W with 3/8" Pushrod and 7/16" Stud (50288866) – $8.99
- Engine Valve Spring (50286901) – $13.99
- Hi-Tech 6.250" Long, .080" Wall, 5/16" Diameter Pushrod (50289351) – $16.99
What are the top-rated Performance and Racing Products that fit the 1982 Lincoln Town Car?
Out of 48 reviews by customers, our 1982 Lincoln Town Car Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1982 Lincoln Town Car and their top-rated products:
- Performance Radiators
- Thermocap Radiator Cap (6900022) – $53.99
What types of Performance and Racing Products do you sell for my 1982 Lincoln Town Car?
As of 3/1/26, these are some of the most in-demand types of Performance and Racing Products for a 1982 Lincoln Town Car:
Can I get help with 1982 Lincoln Town Car Performance and Racing Product orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Lincoln Performance and Racing Products and more.
What is your return policy for Lincoln Town Car Performance and Racing Products?
Advance Auto Parts keeps returns simple. For new Lincoln Town Car Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
