1982 Honda Prelude Belts and Hoses

Essential 1982 Honda Prelude Belts and Hoses

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 26 Inch Length (Part No.87701)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 26 Inch Length

from

$12.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Premium Molded Heater Hose (Part No.18206)

Premium Molded Heater Hose

from

$18.29
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Gates – Premium Molded Heater Hose (Part No.18020)

Premium Molded Heater Hose

from

$14.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:
  • Has all the quality features of Gates molded coolant hose and similar to OEM specifications
  • Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
  • EPDM tube, synthetic fiber knit reinforcement, EPDM cover
  • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
  • Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
  • Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length (Part No.86051)

Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 16 Inch Length

from

$30.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Dayco – Molded Heater Hose; EPDM Rubber, 1/2 Inch Diameter, 4 1/4 Inch Length (Part No.87306)

Molded Heater Hose; EPDM Rubber, 1/2 Inch Diameter, 4 1/4 Inch Length

from

$10.79
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:
  • Meets the requirements of SAE J20R3, Class D-1
  • Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Engineered as an OEM replacement
  • The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
See More

Gates – Straight Heater Hose: EPDM, Direct Fit, 0.25" Inside Diameter (Sold by foot) (Part No.28407)

Straight Heater Hose: EPDM, Direct Fit, 0.25" Inside Diameter (Sold by foot)

from

$0.99
Premium hose constructed for long service life.

Product Features:
  • Good resistance to high temperatures for extended periods of time, which prolongs service life
  • Meets SAE 20R3 Standard Wall Class D-2 requirements
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • CAUTION: Do not use for fuel or oil transfer applications
  • CAUTION: Do not use for fuel or oil transfer applications
  • PLEASE NOTE: Item is priced and sold by the foot. See store for details.
See More

Gates – Safety Stripe« Standard Straight Heater Hose (Part No.28409)

Safety Stripe« Standard Straight Heater Hose

from

$2.49
Premium hose constructed for long service life.

Product Features:
  • Good resistance to high temperatures for extended periods of time, which prolongs service life
  • Meets SAE 20R3 Standard Wall Class D-2 requirements
  • Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
  • Caution: Do not use for fuel or oil transfer applications
  • PLEASE NOTE: Item is priced and sold by the foot. See store for details.
See More

Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)

Metal Line Kit for Engine Oil Coolers

from

$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:
  • Metal line kit
  • For use in engine oil cooler applications
  • Routes oil lines past exhaust manifolds
  • Provides protection where standard hoses can fail
See More

Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)

1/2" x 12' Engine Oil Cooler Hose

from

$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:
  • Engine oil cooler hose
  • Size: 1/2″ x 12′
  • Designed for engine oil applications
  • 12′ hose length accommodates most applications
See More

Driveworks – Automotive V-Belt, Driveworks (Part No.37015)

Automotive V-Belt, Driveworks

from

$5.49
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.

Product Features:
  • This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
  • Polyester cords provide extreme tension-holding capability for longer belt life
  • The raw edge belt design delivers the maximum gripping power
  • The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
See More

Mitsubishi – Multi-Rib (Serpentine) Belt (Part No.W100036481MBL)

Multi-Rib (Serpentine) Belt

from

$16.40
The Mitsuboshi Multi Rib (Serpentine) Belt meets or exceeds the vehicle manufacturer’s specifications for durability, fit and quality. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
See More

Bando – Multi Rib (Serpentine) Belt (Part No.W1000105917BAN)

Multi Rib (Serpentine) Belt

from

$10.96
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Strong tensile cords limit stretching.
  • Supports higher horsepower loads.
  • Made from high strength synthetic rubber.
See More

Dayco – Bottom Cog V-Belt; 34.25 Inch Long, Exact Fit Premium Quality (Part No.17343)

Bottom Cog V-Belt; 34.25 Inch Long, Exact Fit Premium Quality

from

$14.29
Dayco’s high performance HD V-belt is one of the most innovative, top performing belts for its application. By combining raw-edge construction with a specially formulated polyester cord treatment, it offers excellent resistance to repeated flexing and protection against heat, oil and grease as well as the strength, stability and reliability required for vehicles that still need a heavy-duty V-belt.

Product Features:
  •  Designed for efficient power transmission to vehicle accessories in today’s trucks and buses
  •  Provides greater durability and flexibility – 35% stronger than all previous versions
  •  Features specially treated cords for added strength, stability and reliability
  • Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
See More

Gates – Automotive XL« High Capacity V-Belt (Part No.9360)

Automotive XL« High Capacity V-Belt

from

$26.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.

Product Features:
  • Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
  • Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
  • Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
  • Resists oil, heat, ozone, weather and aging for improved belt life
  • Meets or exceeds SAE J636C specifications
See More

ContiTech – Drive V-Belt (Part No.W100033142CON)

Drive V-Belt

from

$15.03
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Polyester fiber tensile members and a ribbed belt design.
See More

Gates – Automotive XL« High Capacity V-Belt (Part No.7385)

Automotive XL« High Capacity V-Belt

from

$26.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.

Product Features:
  • Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
  • Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
  • Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
  • Resists oil, heat, ozone, weather and aging for improved belt life
  • Meets or exceeds SAE J636C specifications
See More

ContiTech – Drive V-Belt (Part No.W1000655835CON)

Drive V-Belt

from

$11.75
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Polyester fiber tensile members and a ribbed belt design.
See More

ContiTech – Multi Rib (Serpentine) Belt (Part No.W100020803CON)

Multi Rib (Serpentine) Belt

from

$19.88
ContiTech Serpentine Belts come in a wide range of sizes and are designed to be oil-resistant and temperature-stable from -22F to 176F (-30C to 80C). ContiTech Serpentine Belts deliver 98% power efficiency. While a lower profile design easily handles higher engine revs, reducing noise and providing cooler running temperatures. High performance construction features include polychloroprene rubber cover and body, polyester fiber tensile members, and a ribbed belt design. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:
  • OE-Equivalent.
  • Direct fit for easy installation.
  • Resistant against wear, oil and heat.
  • Temperature-stable from -22F to 176F (30C to 80C).
  • Delivers over 98% power efficiency.
  • High performance construction.
  • Polychloroprene rubber cover and body.
  • Polyester fiber tensile members and a ribbed belt design.
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 26" Long, 1.19" Diameter (Part No.E71478)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 26" Long, 1.19" Diameter

from

$38.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25265)

Vulco-Flex½ II Flexible Coolant Hose

from

$70.99
Product Features:
  • Improved sealing surface for greater leak resistance
  • High flexibility for easy installation
  • Maximum vehicle coverage with minimum inventory
  • Resistant to heat, oil and ozone
  • Rated for SAE 20R5 Class D-2 performance
  • Temperature Range: up to +257 Deg. F (+125 Deg. C)
  • Note: Gates recommends replacing clamps each time a new coolant hose is installed
  • Caution: Do not use for fuel or oil transfer applications
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 21.50" Long, 1" Diameter (Part No.E71228)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 21.50" Long, 1" Diameter

from

$29.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 21" Long, 1.03" Diameter (Part No.E71048)

Curved Radiator Hoses: EPDM Rubber, Standard Duty, 21" Long, 1.03" Diameter

from

$16.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:
  • Meets SAE J20R4, Class D-1 requirements
  • Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
  • Provides excellent protection against external elements
See More

1982 Honda Prelude Belts and Hoses

You count on your 1982 Honda Prelude to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 18 Belts and Hoses ranging in price from $4.99 to $79.99, you’re sure to find everything you need for your 1982 Honda Prelude.

Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 6 different brands like Dayco, Imperial, and Gates. 1982 Honda Prelude Belts and Hoses start as low as $4.99!

One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 18 extensive product reviews on 1982 Honda Prelude Belts and Hoses.

Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1982 Honda Prelude below to get started!

Top-Rated Belts and Hoses Brands For Your 1982 Honda Prelude

Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1982 Honda Prelude running right for years to come. In our inventory you’ll find brands like Dayco, Imperial, Gates, and even more.

Popular Driveworks Belts and Hoses

You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 1982 Honda Prelude back on the road. Some of the top-rated Driveworks products in these categories are:
Automotive V-Belt
from $5.29
(1)
Automotive V-Belt
V-Belts
Automotive V-Belt
from $5.29
(3)
Automotive V-Belt
V-Belts
Automotive V-Belt, Driveworks
from $5.49
(1)
Automotive V-Belt, Driveworks
V-Belts