1981 Toyota Pickup Differentials

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), pinion shim kit, marking compound and brush. No side shims.

Product Features:

• Fits Toyota 7.5″ front with 6 cylinder engine
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Product Features:

• Roll pin
• Fits Toyota 8″ with 4 cylinder engine

Product Features:

• TOYOTA 8″ V6&4CLY TURBO

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landrcuiser (fine spline pinion) & T100/Tacoma with factory locker. 30mm socket, M20 x 1.5 thread.

Product Features:

• Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landcruiser with 30 spline pinion and Tacoma/T100 with factory locker
• 20mm x 1.5 thread
• 30mm socket

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits standard rotation Toyota 7.5″
• 7.500″ ring gear diameter
• 23 spline pinion
• 10 ring gear bolts
• 5.29 ratio

Product Features:

• Conversion kit
• Fits Toyota V6 rear with 29 spline pinion
• Includes yoke , pinion seal, and pinion nut

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Toyota 8″ with 4 cylinder engine
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

Bearing race driver for Toyota 7.5″, 8″ rear. (TOY32307). No return.

Product Features:

• Bearing race driver
• Fits 32307 race
• All steel construction

Toyota 8″ & V6 pinion nut washer.

Product Features:

• Pinion nut for Toyota 8″ and V6

Toyota 7.5″ crush sleeve, 2.185″ long.

Product Features:

• Crush sleeve for Toyota 7.5″
• 2.185″ tall

Toyota 8″ & V6 gasket.

Product Features:

• Dropout gasket
• Fits Toyota 8″ and V6

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

• Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
• Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
• Durable construction – designed and manufactured to strict specifications for reliable performance
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

• Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

V6 standard Open case, bare.

Product Features:

• Standard open carrier case
• Does not include spider gears
• Fits Toyota V6

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• TOYOTA 8″ BRNG & SEAL MASTER KIT

Product Features:

• Cross pin shaft
• Fits Toyota 8″ with 4 cylinder engine

7.5″ V6 & 4cyl side shim kit (incl. 7 shims).

Product Features:

• Carrier shim kit
• Fits Toyota 7.5″

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Low swell in hydrocarbon fluids
• Design type: spring loaded; multi-lip
• Provides good low temperature capability
• Temperature range: -40°F to 225°F; -40°C to 107°C
• Delivers quality and reliable performance for every type of repair

Formulated to meet the specific requirements of Subaru vehicles equipped with conventional (non-CVT) transmissions up to model year 2005. Recommended for service-fill in all Subaru automatic transmissions where SUBARU ATF HP is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. Idemitsu is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. Idemitsu application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

• Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
• Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
• Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
• Advanced anti-wear technology provides maximum protection to gears and bearings
• Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
• Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
• Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
• Advanced anti-wear technology provides maximum protection to gears and bearings

8″ standard Open side gear Thrust washer.

Product Features:

• Side gear thrust washer
• Fits Toyota 8″ with 4 cylinder engine

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear. This kit fits applications with a 27 spline pinion.

Product Features:

• Fits Toyota V6 rear
• Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Product Features:

• KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT