from

$282.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 8.2″ Buick, Oldsmobile and Pontiac
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$389.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. This gear set does not have an ABS provision on the pinion.

Product Features:

Fits GM 8.5″ and 8.6″
8.50″ ring gear diameter
30 spline pinion
10 ring gear bolts
5.13 ratio

from

$601.99

Yukon spider gear set for GM 8.2″ Buick, Olds, Pontiac Dura Grip posi, 28 spline. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY.

Product Features:

Spider gear kit
Fits 8.2″ Buick, Oldsmobile and Pontiac with Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$14.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$15.99

Standard open side gear thrust washer for 8.5″ GM.

Product Features:

Side gear thrust washer
Fits GM 8.5″

from

$219.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M88010 race
All steel construction

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$38.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$373.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
14 piece kit
Composite clutches

from

$18.09

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1964-1970 Chevrolet 8.2 inch 10 bolt & 1970-1981 GM 8.5 inch ring gear

Product Features:

.047″ thick cellulose/nitrile composite gasket material
Precision die cut
Reusable

from

$153.99

7.5″ & 7.625″ GM 82-99 PINION KIT .

Product Features:

Fits 1982-1999 GM 7.5″ and 7.625″
Uses Koyo bearings and races
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.

from

$399.99

GM 7.5″ & 7.6″ DURA GRIP case, bare, 3.23 & up, 26spline & 28spline.

Product Features:

Dura Grip positraction carrier case
Does not include spider gears
Fits GM 7.5″ and 7.625″
3.23 and up ratios only

from

$59.99

Product Features:

8.5 “P” AXLE MINI INSTALL KIT

from

$74.99

Product Features:

Fits 8.2″ Buick, Oldsmobile and Pontiac
Chrome

from

$37.99

The tremendous shock loads generated at launch by most any drag racing vehicle equipped with todays sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. They are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.

Product Features:

Forged From Premium Grade 8740 Chrome Moly Steel
Heat Treated
Nominally Rated At 200,000 Psi Tensile Strength
Specially Hardened, Precision Ground Washers
3/8″-24 RH Thread Size
0.8″ Underhead Length
200,000 PSI

from

$124.99

MiniSpool

from

$156.99

Product Features:

KIT BRG&SL GM 8.5″ 10 BLT MSTR NON IFS FRONT / REAR

from

$59.99

Product Features:

Super carrier shim kit for Ford 7.5″, GM 7.5″, 7.625″, 7.6″ IFS, 7.6″ IRS, 7.75″, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and GM 8.5″ front and rear
Interlocking design makes installation much easier

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$336.99

Yukon positraction internals (0.795″ diameter) for 8.5″ GM with 28 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects. This kit is compatible with Yukon Dura Grip or Eaton positractions. It will not fit a factory Gov-Loc positraction.

Product Features:

Spider gear kit
Fits GM 8.5″ with 28 spline Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$84.99

Notched cross pin shaft for 7.5″ GM. This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers.

Product Features:

Cross pin shaft
Fits GM 7.5″
Notched
Not compatible with Spartan Lockers or Lock Rights

from

$10.99

Product Features:

Clutch guide
Fits GM 7.5″ and 7.625″ Dura Grip

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$2.79

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$23.79

CONE

from

$3.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$6.49

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles.
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$9.99

Pinion nut for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.0″, 8.25″, 8.5″, 8.6″, 9.25″ IFS, 9.5″ & Oldsmobile Dropouts. 1 1/4″ socket, 7/8″ x 14 thread.

Product Features: