from

$9.99

Pinion seal for GM 8.5″, 8.2″, Buick, Oldsmobile, and Pontiac.Yukon Mighty seal.

Product Features:

Pinion seal
Fits GM 8.5″ rear, 8.2″ and 8.2″ in Buick, Oldsmobile and Pontiac

from

$441.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$8.79

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$151.99

MiniSpool

from

$113.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

MASTER BRG KIT 8.2 CAR

from

$21.99

Product Features:

Pinion depth shims for GM 7.5″, 7.625″, 7.6 IFS, 7.6 IRS, 7.75″, 8.2″, 1955-1964 passenger car and 12 bolt car and truck

from

$65.99

Add some bling to the underside of your car with Mr. Gasket’s chrome differential cover. This chrome-plated steel cover is made to fit GM 10-bolt with 8 1/2 in ring gear. Is a complete kit with a gasket and bolts.

Product Features:

Made Of Chrome Plated Steel
Fits GM 8.5-Inch 10 Bolt
Complete Kit With Gasket And Bolts

from

$249.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 8.5″ Oldsmobile with 28 spline axles
Fits 8.5″ Oldsmobile with 31 spline axles
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$829.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits GM 7.625″ with 28 spline axles
3.23 ratio and up only
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$399.99

GM 7.5″ & 7.6″ DURA GRIP case, bare, 3.23 & up, 26spline & 28spline.

Product Features:

Dura Grip positraction carrier case
Does not include spider gears
Fits GM 7.5″ and 7.625″
3.23 and up ratios only

from

$2.49

Product Features:

RING GEAR BOLT 8.5″ 7.5″ 7/16 X 20 LEFT HAND

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$483.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
18 piece kit
Steel clutches

from

$2.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$8.49

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$2.79

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$10.99

Product Features:

Clutch guide
Fits GM 7.5″ and 7.625″ Dura Grip

from

$156.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits 8.5″ Oldsmobile with 31 spline axles
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$41.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$42.99

Product Features:

Shim kit
Fits GM 7.5″ and 7.625″ with Eaton positraction

from

$11.99

GM 7.5″ standard Open side gear thrust washer.

Product Features:

Side gear thrust washer
Fits GM 7.5″

from

$153.99

Product Features:

Positraction spring kit
Fits GM 7.5″ and 7.625″ Dura Grip
Includes preload plates

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$18.09

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1964-1970 Chevrolet 8.2 inch 10 bolt & 1970-1981 GM 8.5 inch ring gear

Product Features:

.047″ thick cellulose/nitrile composite gasket material
Precision die cut
Reusable

from

$226.99

Yukon yoke for 8.5″ or 8.6″ GM (mech 3R) with a U/joint size and triple lip design. 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring. This yoke uses inside snap rings. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.5″ and 8.6″
30 spline
Mechanics 3R u-joint size
2.556″ snap ring span
1.125″ cap diameter
Inside snap ring design
Strap style

from

$101.99

Product Features:

MINI SPOOL GM 7 1/2″ 28 SPLINE

from

$59.99

Product Features:

Super carrier shim kit for Ford 7.5″, GM 7.5″, 7.625″, 7.6″ IFS, 7.6″ IRS, 7.75″, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and GM 8.5″ front and rear
Interlocking design makes installation much easier

from

$344.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features: