1981 Buick Regal Air Intakes
Find Your Specific 1981 Buick Regal Air Intakes
Below you will find various in-demand Buick Air Intakes, components and accessories for your 1981 Regal. Advance Auto Parts has popular Regal parts like Air Cleaner Parts, Carburetor Parts, Throttle Bodies & Carb Parts and more. You’ll also find aftermarket and OEM Air Intakes for other Regal model years including
2003,
2004,
2011,
2012,
2013,
2014,
2015,
2016,
2017 and more. Select a category of 1981 Buick Regal Air Intakes below and start saving instantly.
Popular 1981 Buick Regal Air Intakes Categories
Essential Air Intakes for 1981 Buick Regals
Carquest Premium – Carburetor Choke Pull-Off (Part No.ECE3013)
from
$34.49
The Carburetor Choke Pull-Off is typically mounted on the outside of the carburetor and is designed to open the choke plate slightly when an engine is first started cold. The choke pull-off is an emission control device but is more importantly required for optimum engine operation in the first several minutes of run-time in cold weather conditions.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1038)
from
$15.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1850)
from
$27.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1743)
from
$24.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Delphi – Throttle Position Sensor (Part No.SS10459)
from
$50.99
Delphi’s ever growing portfolio of high quality vehicle sensors are backed by stringent OE development and product validation methods. We offer a wide range of sensors, including ABS, camshaft, crankshaft, knock, EGT, MAP, temperature, throttle position, and vehicle speed sensors for a variety of vehicle applications. All of our sensors are tested and calibrated to OE standards, ensuring accurate readings, which helps to reduce comebacks.
Product Features:
See More
Product Features:
- Delphi sensors are built to meet or exceed OE requirements and testing
- Not impacted by temperature changes and provide robust, long-lasting sensor protection
- Designed digital output for maximum signal to noise ratio
Carquest Premium – Throttle Sensor (Part No.ECC1227)
from
$124.99
Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.
Product Features:
See More
Product Features:
- Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
- 100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
- Designed to meet or exceed all OEM specifications in fit, form & function
- Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Dorman – Steel Cup Expansion Plug 1 In., SC, Height 0.250 (sold by each) (Part No.555-018)
from
$2.99
This engine expansion plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this engine expansion plug matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Edelbrock – Performer Intake Manifold Small-Block Chevy (Part No.3706)
from
$401.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 Deg Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
- Accepts Late-Model Choke; Waterneck; and HEI
- Accepts A/C And Alternator
- Accepts Exhaust Heated Chokes and Accepts EGR
Edelbrock – Performer Air-Gap Intake Manifold for 1955-86 Small-Block Chevy (Part No.2601)
from
$395.99Product Features:
- Based on Performer Series with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg .Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- Fits Both Spread and Square Bore Carburetors
- Also in Polished/PermaStar/EnduraShine Finish
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Dorman – Lower Intake Manifold Gasket Set: 18 Piece Set (Part No.615-206)
from
$67.99
This engine intake manifold gasket set is designed to match the original gaskets required to reseal and restore proper function to the intake manifold on specified vehicles.
Product Features:
See More
Product Features:
- Direct replacement – this engine intake manifold gasket set is designed to match the original gaskets required to reseal and restore proper function to the intake manifold on specified vehicles
- Restores functionality – this gasket set is made to fit and fully restore part functionality after the original gasket fails
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Felpro – Valley Pan Gasket Set (Part No.MS 96032)
from
$44.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- RIGHT TYPE – Valve stem seals designs are application-specific for the repair occasion using either deflector (umbrella) seals, O-ring style or positive seals
- QUALITY MATERIALS – Each valve stem seal features materials based on the specific application for your vehicle repair
- ENGINEERING EXPERTISE – Parts are reviewed, validated and approved by Fel-Pro engineers through rigorous research, development and testing
- INSTALLATION AID – Installation tool included to protect inner lip of seal from damage during seal installation
- COVERAGE – Available for domestic and foreign nameplate vehicles
Felpro – Valley Pan Gasket Set (Part No.MS 96027)
from
$32.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- RIGHT TYPE – Valve stem seals designs are application-specific for the repair occasion using either deflector (umbrella) seals, O-ring style or positive seals
- QUALITY MATERIALS – Each valve stem seal features materials based on the specific application for your vehicle repair
- ENGINEERING EXPERTISE – Parts are reviewed, validated and approved by Fel-Pro engineers through rigorous research, development and testing
- INSTALLATION AID – Installation tool included to protect inner lip of seal from damage during seal installation
- COVERAGE – Available for domestic and foreign nameplate vehicles
Carquest Premium – Multi-Use Connector (Part No.PTA1166)
from
$20.99
Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.
Product Features:
See More
Product Features:
- Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- Product constructed to meet all design and operating characteristics as intended by the manufacturer.
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
Carquest Premium – Multi-Use Connector (Part No.PTA1632)
from
$45.99
Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.
Product Features:
See More
Product Features:
- Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- Product constructed to meet all design and operating characteristics as intended by the manufacturer.
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
Edelbrock – Carb, Thunder Series Avs2 Annualr Boosters 650 Cfm Black Electric Choke (Part No.19063)
from
$531.99
The Edelbrock AVS2 Series No. 19063 is a black-finished carburetor with electric choke that is designed and calibrated for optimum street performance in engines that require 650 CFM of air-fuel flow. The AVS2 is a perfect replacement or upgrade that features annular flow primary boosters with a new calibration for improved off-idle and cruising performance. The annular flow booster design delivers improved fuel atomization to eliminate flat spots that may be encountered as the carburetor transitions from idle to full throttle. Each annular flow booster features eight equally spaced orifices to improve fuel metering from idle to the main circuit. The improved flow metering makes this carburetor ideal for use with a wide variety of small- and big-block engines with either dual- or single-plane intake manifolds. The Edelbrock AVS2 No. 19063 includes both timed and full vacuum ports for ignition advance. It comes with: .101 primary and.098 secondary metering jets
See More
Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)
from
$474.99
The Edelbrock 1407 Performer Series 750 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke
- 4 Barrel Count
- Square Bore
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Holley – Performance and Race Carburetor: 500 CFM, No Choke, 2 Barrel, 2300 Bore, Single Inlet (Part No.0-4412CT)
from
$649.99
Competition fuel curves provide safe and reliable horsepower for high performance race engines.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
Holley – Street Carbs (Part No.0-8007)
from
$849.99
Classic Holley carbs have been a staple for rodders around the world for decades. They’re calibrated for use on stock to mildly modified vehicles and have that classic Holley look. Holley’s 0-8007 is calibrated and intended for small V8s or 6 cylinder engines as well as 2×4 street tunnel ram style set ups. Plus, it is Gold Dichromate coated for durability and classic Holley looks. Don’t trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Factory Preset Elec Choke For Easy Startups
- For All Weights/Gearing/Trans For Smooth Open Of Secondaries
- Single Feed Fuel Inlet For Easy Installation
- Power Valve Blow-Out Protection
- Does Not Work w/A.O.D. Transmissions
- Installation/Tuning DVD Incl.
Felpro – Engine Intake Manifold Bolt Set (Part No.ES 72226)
from
$37.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Premium quality parts
- Engineered and manufactured specifically for the repair environment
- Unsurpassed quality you can trust
Mr. Gasket – Intake Bolt Kit (Part No.5003)
from
$87.99
Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.
Product Features:
See More
Product Features:
- Chrome plated
- Grade 8
- 12-point head
- AN washers with no exposed shoulder for a professional appearance
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$36.99
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", Hex Style Head Type, Polished, Ss (Part No.434-2001)
from
$56.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
- 1″ Long
Carquest – Carburetor Choke Thermostat (Part No.779-1485)
from
$69.05
Carquest distributes a full line of engine management products, providing the aftermarket with premium quality and comprehensive coverage.
See More
Wells Vehicle Electronics – Carburetor Choke Thermostat (Part No.2C1027)
from
$26.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Upgrade your 1981 Buick Regal with Top-Quality Air Intakes
When it comes to maintaining or upgrading your 1981 Buick Regal, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Buick or enhancing its overall performance, Air Intakes are key to keeping your Regal functioning at its best. At Advance Auto Parts, we offer a wide selection of 75 Air Intakes for the 1981 Buick Regal, designed to meet your needs without breaking the bank.
From
Air Cleaner Part
replacements to
Carburetor Parts
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Air Intakes for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Air Intakes for your 1981 Buick Regal at great prices.
Our Air Intakes inventory for this model
ranges from just $4.29 to $1,949.99, with
an average price of $552.46.
Our 75 Air Intakes in stock come from 9 trusted brands, so you’re sure to find the right part for your 1981 Buick Regal without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1981 Buick Regal, we stock popular OEM and aftermarket Air Intakes from top names
like FELPRO Holley, and more.
FELPRO Air Intakes
start at just $4.29 and boast an impressive 4.6 stars average rating from customers.
With 182 customer reviews and counting, our 1981 Buick Regal Air Intakes have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Air Intake upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1981 Buick Regal is always ready to roll. We’re committed to providing you with everything you need to keep your Regal in top shape, all in one place.
Start shopping confidently below for your 1981 Buick Regal!
Best-Selling Air Cleaner Parts for 1981 Buick Regals
Enhance the driving experience in your Buick with 1 quality Air Cleaner Part components, starting at $4.29.
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Most Popular 1981 Buick Regal Carburetor Parts
Customize your Buick with 59 Carburetor Parts products
like Carburetors, all
priced under $1,949.99.
Holley – Performance and Race Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Dual Inlet (Part No.0-4776C)
from
$799.99
The Ultra Double Pumper Carburetors feature all aluminum construction and are equipped with metering blocks and a base plate made from 6061-T6 billet aluminum. Three different anodized color options (Red, Blue, or Black) allow for a personalized look while maintaining the ultra high strength and durability you get from billet. They weigh in at approximately 5 lbs less than a comparable zinc carburetor. The new Ultra Double Pumper Carburetors have an enhanced fuel curve for optimum performance, with many more features such as aluminum construction; anodized billet aluminum metering blocks and base plate; 4 corner idle for precise idle control; mechanical secondaries for great performance; clear fuel level sight plugs for easy, no mess fuel level adjustments; Ford automatic transmission kickdown for use on popular Ford transmissions; four vacuum ports for all necessary vacuum accessories; and for the first time on a Double Pumper, factory pre-set electric choke for easy, fast cold start-ups. The clean, polished look coupled with Red, Blue, or Black metering blocks and throttle body will certainly set your ride apart whether you are at the show or track. Dont trust your performance to just anyone, Holley is the only Modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60s.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Optimized Street/Strip Calibration That Works Out Of The Box
- Man. Choke Cable Hand Controlled For Cold Start Control
- Mechanical Secondaries For Awesome Tire Turning Performance
- Dual Accelerator Pumps For Add Fuel Under Initial Acceleration
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
- Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing
- 100% Wet Flow Tested By Holley Technicians
Holley – Prem Street Carbs (Avengers) (Part No.0-80770)
from
$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Street Carburetor: 450 CFM, No Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate (Part No.0-9776)
from
$599.99
Replace your old carburetor with original Holley performance 4160 carburetors. Budget-minded enthusiasts, like you, will be rewarded with maximum performance from your stock or mildly-modified engine. These Holley 4160 adjustable float carburetors are easier to tune than full race carburetors with temperamental secondary metering blocks and dual pumps. Plus, they’re available in your choice of universal or direct fit OE replacement versions with all emission provisions. Bolt-on installation and improved performance; no wonder when car guys think of carburetors, they think of Holley 4160 carburetors!
Product Features:
See More
Product Features:
- Universal Holley 4-Barrel Carburetor
Holley – Street Carbs (Part No.0-80508S)
from
$524.99
One of the most widely used Holley carbs of all times -the 0-80508S! Its dual feed fuel inlets assure you get all the fuel you need and its 750 CFM of airflow makes it the perfect performance upgrade carb. Its vacuum secondaries and electric choke make it super easy to use on a wide range of vehicles. Don’t trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
Holley – Street Carbs (Part No.0-8007)
from
$849.99
Classic Holley carbs have been a staple for rodders around the world for decades. They’re calibrated for use on stock to mildly modified vehicles and have that classic Holley look. Holley’s 0-8007 is calibrated and intended for small V8s or 6 cylinder engines as well as 2×4 street tunnel ram style set ups. Plus, it is Gold Dichromate coated for durability and classic Holley looks. Don’t trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Factory Preset Elec Choke For Easy Startups
- For All Weights/Gearing/Trans For Smooth Open Of Secondaries
- Single Feed Fuel Inlet For Easy Installation
- Power Valve Blow-Out Protection
- Does Not Work w/A.O.D. Transmissions
- Installation/Tuning DVD Incl.
Holley – Prem Street Carbs (Avengers) (Part No.0-81570)
from
$671.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Manual Choke For Precise Cold Start Control
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Street Carbs (Part No.0-3310C)
from
$631.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal calibration for easy bolt-on performance
- Man. Choke Cable Hand Controlled For Cold Start Control
- Vacuum Secondaries For Use On Wide Variety Of Vehicles
- Dual feed fuel inlets for constant high volume fuel delivery
- Power Valve Blow Out Protection
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Street Carbs (Part No.0-1850S)
from
$480.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a
Product Features:
See More
Product Features:
- Vibratory Polished Alum Good Looks/Weight Savings/Lasting Shine
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal Calibration For Easy Bolt-On Performance
- Man. Choke Cable Hand Controlled For Cold Start Control
- Vacuum Secondaries For Use On Wide Variety Of Vehicles
- Single Feed Fuel Inlet For Easy Installation
Holley – Street Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate (Part No.0-1850C)
from
$599.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal Calibration For Easy Bolt-On Performance
- Man. Choke Cable Hand Controlled For Cold Start Control
- Vacuum Secondaries For Use On Wide Variety Of Vehicles
- Single Feed Fuel Inlet For Easy Installation
- Power Valve Blow Out Protection
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
- Compensates For All Vehicle Weights Gearing/Transmissions
Holley – Off Road Carbs (Part No.0-90670)
from
$799.99
The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Extreme Off Road Environments
- Single Feed Fuel Inlet For Ease Of Installation
- Optimized Off-Road Calibration That Works Out-Of-The-Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- One Piece Off-Road Vent Tube Eliminates Fuel Spillover
- Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
- Limited Lifetime Warranty Defects In Material/Workmanship
Holley – Street Carburetor: 500 CFM, Manual Choke, 2 Barrel, 2300 Bore, Single Inlet, Shiny (Part No.0-4412S)
from
$534.99
The 0-4412 is designed as a stock replacement for 2BBL street applications as well as being mandated for some oval track racing sanctioning bodies. Whether you are looking for a replacement carburetor to replace your tired and worn factory 2BBL or one to push you to the finish line on Saturday night, the Holley 0-4412 Performance 2BBL is the perfect choice.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
Holley – Street/Strip Carbs (Part No.0-4779C)
from
$849.99
The Ultra Double Pumper Carburetors feature all aluminum construction and are equipped with metering blocks and a base plate made from 6061-T6 billet aluminum. Three different anodized color options (Red, Blue, or Black) allow for a personalized look while maintaining the ultra high strength and durability you get from billet. They weigh in at approximately 5 lbs less than a comparable zinc carburetor. The new Ultra Double Pumper Carburetors have an enhanced fuel curve for optimum performance, with many more features such as aluminum construction; anodized billet aluminum metering blocks and base plate; 4 corner idle for precise idle control; mechanical secondaries for great performance; clear fuel level sight plugs for easy, no mess fuel level adjustments; Ford automatic transmission kickdown for use on popular Ford transmissions; four vacuum ports for all necessary vacuum accessories; and for the first time on a Double Pumper, factory pre-set electric choke for easy, fast cold start-ups. The clean, polished look coupled with Red, Blue, or Black metering blocks and throttle body will certainly set your ride apart whether you are at the show or track. Dont trust your performance to just anyone, Holley is the only Modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60s.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Optimized Street/Strip Calibration That Works Out Of The Box
- Manual Choke For Precise Cold Start Control
- Mechanical Secondaries For Awesome Tire Turning Performance
- 4 Corner Idle Allows You To Precisely Control Your Idle System
- Dual Accelerator Pumps For Add. Fuel Under Initial Acceleration
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
- Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing
Holley – Carburetor – 770 CFM Alum Street Avenger E/C (Part No.0-83770)
from
$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Features A Tumble Polished Finish Can Also Be Hand Polished
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Glass Fuel Level Sight Windows For Easy Safe Float Adjustments
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- 4 Corner Idle Allows You To Precisely Control Your Idle System
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
Holley – Prem Street Carbs (Avengers) (Part No.0-81670)
from
$671.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Manual Choke For Precise Cold Start Control
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
Holley – Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80458SA)
from
$516.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Vibrant Polished Alum Good Looks/Weight Savings/Lasting Shine
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal Calibration For Easy Bolt-On Performance
- Factory Preset Electric Choke For Easy Startups
- For All Weights/Gearing/Trans For Smooth Open Of Secondaries
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
- Power Valve Blow-Out Protection
- Clear Fuel Level Sight Glasses
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Street Carburetor: 750 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (Part No.0-80459SA)
from
$536.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Vibrant Polished Alum Good Looks/Weight Savings/Lasting Shine
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal Calibration For Easy Bolt-On Performance
- Factory Preset Electric Choke For Easy Startups
- For All Weights/Gearing/Trans For Smooth Open Of Secondaries
- Single Feed Fuel Inlet For Easy Installation
- Power Valve Blow-Out Protection
- 100% Wet Flow Tested By Holley Technicians
Holley – Professional Race Carburetor: 1250 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Hard Core Gray (Part No.0-80908HB)
from
$1949.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Holley – Professional Race Carburetor: 1150 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Hard Core Gray (Part No.0-80906HB)
from
$1899.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Holley – Professional Race Carburetor: 1250 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Shiny (Part No.0-80908BK)
from
$1799.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Holley – Professional Race Carburetor: 1050 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Hard Core Gray (Part No.0-80902HB)
from
$1699.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Holley – Professional Race Carburetor: 1050 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Shiny (Part No.0-80903BK)
from
$1649.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Holley – Professional Race Carburetor: 1050 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Hard Core Gray (Part No.0-80903HB)
from
$1649.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Holley – Professional Race Carburetor: 1050 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Shiny (Part No.0-80903RD)
from
$1649.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Holley – Professional Race Carburetor: 950 CFM, No Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80901RD)
from
$1599.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Top Picks for 1981 Buick Regal Throttle Bodies & Carb Parts
Upgrade Buick Regals with top-quality Throttle Bodies & Carb Parts parts, including 2 OEM and aftermarket selections for your 1981 model.
Carquest Premium – Multi-Use Connector (Part No.PTA1166)
from
$20.99
Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.
Product Features:
See More
Product Features:
- Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
- Product constructed to meet all design and operating characteristics as intended by the manufacturer.
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
Carquest Premium – Throttle Position Sensor (Part No.ECC1245)
from
$103.99
Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.
Product Features:
See More
Product Features:
- Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
- 100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
- Designed to meet or exceed all OEM specifications in fit, form & function
- Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.
In-Demand Intake Manifold Parts for 1981 Buick Regals
Select from 5 premium Intake Manifold Parts parts for your 1981 Buick Regal, with prices ranging from $5.99 to $401.99.
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", 12 Point Head Type, Polished, With Washers (Part No.434-2101)
from
$60.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 92328)
from
$28.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
- Includes all parts needed to complete the repair
Edelbrock – Performer Buick 3.8L, 4.1L V6 Intake Manifold (Part No.5486)
from
$401.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- Not for C-3 and C-4 Electronic Fuel Mngmt Systems
ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", Hex Style Head Type, Polished, Ss (Part No.434-2001)
from
$56.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
- 1″ Long
Most Sold 1981 Buick Regal Carburetor Kits
Explore our best-selling Buick parts for the 1981 Regal among 3 OEM and aftermarket options starting from $24.99.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1890)
from
$28.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1850)
from
$27.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1743)
from
$24.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Top-Rated Air Intakes Brands For Your 1981 Buick Regal
Shop for the best-rated brands offering Air Intakes and other products for your 1981 Buick Regals. Below you’ll find some of our best rated Air Intakes from FELPRO and Holley, and more. Air Intakes from these brands that fit a 1981 Regal start at just $4.29 and are rated as high as 4.6 stars. OEM and aftermarket Air Intakes don’t get more top quality, durable, and affordable than from the brands below.
Popular FELPRO 1981 Buick Regal Air Intakes
When it comes to maintaining or upgrading your 1981 Buick Regal, using quality Air Intakes is essential to ensure durability and a perfect fit. FELPRO ticks all of those boxes. We offer a wide selection of FELPRO Air Intakes, specifically designed for the 1981 Buick Regal. With over 1 FELPRO brand Air Intakes in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $4.29. Plus, with over 39 customer reviews and an average rating of 4.6 stars, you can trust that our FELPRO Air Intakes will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
Popular Holley 1981 Buick Regal Air Intakes
Holley auto parts is one of the highest quality Air Intake brands in the market. Any 1981 Buick Regal owner should feel confident when installing genuine Holley parts in their vehicle. To ensure the best fit and performance for your 1981 Regal, Advance Auto Parts carries a full inventory of 3 Holley Air Intakes. Plus you will be keeping your Buick in peak condition while saving money because prices on these Holley Air Intakes range from $599.99 to $799.99, plus, with more than 5 customer reviews and an impressive 4.1 stars average rating, you can be confident the Fram Air Intakes below will deliver on both quality and value.
from
$599.99
(2)
Street Carburetor: 450 CFM, No Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate
“REPLACED EXHISTING HOLLEY CARB,LIKE THE PRODUCT LOOKS GOOD ON ENGINE, POLISHED ,EXCELLENT CARBS USED ON OTHER PROJECTS”
from
$799.99
(1)
Performance and Race Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Dual Inlet
“Great price on a performance carb. Will be used on a “restored” project. Holley is aLways a good choice”
FAQs for 1981 Buick Regal Air Intakes
Which Air Intakes are best-sellers for 1981 Buick Regals?
Out of 75 Air Intakes that fit 1981 Buick Regals, the following parts are the top sellers:
- Street Carbs (6340180) – $524.99
- Street Carbs (17120021) – $480.99
- Carburetor Choke Thermostat (5011973) – $69.05
What’s the price range for 1981 Buick Regal Air Intakes?
Air Intake prices for the 1981 Buick Regal start at $4.29 and go up to $1,949.99 for the most premium parts.
What’s the average price of a Air Intake for a 1981 Buick Regal?
The average price for Air Intakes for the 1981 Buick Regal is $552.46. Keep in mind the variety of part types within our Air Intake category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Air Intakes for other Buick Regal model years?
What are the cheapest Air Intakes for my 1981 Buick Regal?
The cheapest 1981 Buick Regal Air Intakes we carry in stock are:
- Air Cleaner Mounting Gasket (5785448) – $4.29
- Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (22140133) – $5.99
- Carburetor Choke Pull-Off (12555210) – $18.99
- Carburetor Choke Pull-Off (12555382) – $19.99
- Multi-Use Connector (12447408) – $20.99
What are the top-rated Air Intakes that fit the 1981 Buick Regal?
Out of 182 reviews by customers, our 1981 Buick Regal Air Intakes have an average customer rating of . These are some of the highest-rated Air Intake types for the 1981 Buick Regal and their top-rated products:
- Air Cleaner Parts
- Air Cleaner Mounting Gasket (5785448) – $4.29
- Intake Manifold Parts
- Air Cleaner Mounting Gasket (5785448) – $4.29
What types of Air Intakes do you sell for my 1981 Buick Regal?
As of 11/2/25, these are some of the most in-demand types of Air Intakes for a 1981 Buick Regal:
Can I get help with 1981 Buick Regal Air Intake orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Buick Air Intakes and more.
What is your return policy for Buick Regal Air Intakes?
Advance Auto Parts keeps returns simple. For new Buick Regal Air Intakes and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
