1980 Lincoln Continental Differentials

Axle shaft damaged or bearings worn out: This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Product Features:
• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

Yukon yoke for Ford 9″ with 35 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″
• 35 spline
• 1350 u-joint size
• Outside snap ring design
• 3.625″ snap ring span
• 1.188″ cap diameter
• U-bolt style

Product Features:

• Trac Loc spring for Ford 8.8″
• 31 spline applications only

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″ with 31 spline axles
• Trac Loc positraction
• Clutch style positraction
• Street design
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

• Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! This unit has been machined for use in dropouts with a load-bolt. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

• Fits Ford 9″ with 35 spline axles and loadbolt housing
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

8.8″ Ford low profile TA HD Aluminum rear Cover. This cover will not fit vehicles with independent rear suspension.

Product Features:

• Fits Ford 8.8″
• Aluminum girdle cover

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Product Features:

• R&P FORD 9″ – 6.66 LIGHTWEIGHT

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with Daytona pinion support
• Included are pinion bearings and races, pinion seal, crush sleeve eliminator , complete pinion shim kit, and marking compound with brush.

Product Features:

• Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
• Interlocking design makes installation much easier

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

8″ & 9″ Ford 4-Tab clutch kit with 9 pieces (late TracLoc).

Product Features:

• Clutch kit
• Fits Ford 8″ and 9″ Trac Loc positraction

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 2009 and down Ford 8.8″
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Standard open cross pin shaft (.750″) for Ford 8″, 8.8″, 9″ and Model 20.

Product Features:

• Cross pin shaft for Ford 8″, 8.8″ and 9″ and AMC Model 20
• Fits standard open differentials only
• 0.750″ diameter

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Yukon standard open spider gear kit for 8.8″ Ford (and IFS) with 28 spline axles and 3/4″ pin. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Ford 8.8″ open differential with 28 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Yukon standard open spider gear kit for 7.5″ Ford with 28 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Ford 7.5″ open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
• Includes carrier bearings and races and “super” carrier shim kit

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

Side gear thrust washer (0.875″ shaft) for 8.8″ Ford.

Product Features:

• Side gear thrust washer for Ford 8.8″
• 0.875″ diameter cross pin shaft applications only

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

• Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

RngPnnInstlKt

2 piece solid spacer for Ford 8.8 and 7.5.

Product Features:

• Crush sleeve eliminator kit for Ford 7.5″ and 8.8″