1980 GMC Jimmy Engine Mounts

Anchor 2292 This mount supports the engine and dampen vibration. Each mount is specifically engineered and designed to OE standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

• MAXIMUM LIFE & PERFORMANCE: Both natural and SBR (Styrene Butadiene) rubber provide good abrasion resistance and aging stability to ensure maximum life and performance.
• MEETS OR EXCEEDS DUROMETER MEASUREMENTS: All rubber material is manufactured to specific Durometer (hardness) measurements based on the vehicle’s application requirements.
• HARDENED STEEL FASTENERS: All fasteners are made of hardened steel with heat treated Grade #5 bolts.
• SUPERIOR BOND: A special Chemlok bonding agent is used to ensure a superior rubber-to-metal bond.
• HYDRAULIC MOUNT DESIGN: Hydraulic Mounts (applicable where OE) are designed for most front wheel drive vehicles because transverse drive train mounting.
• For Years: 1968-2005
• Weight approx: 3 Lbs
• Product: Made In The Usa
• Design: Clamshell
• Part Group: 2292, 2292

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

• Gains Both Performance and Longevity
• Will Handle Any and All Torque
• Out Lasts Rubber

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

• Gains Both Performance and Longevity
• Will Handle Any and All Torque
• Out Lasts Rubber

Product Features:

• Re-Engineered to Handle High Horsepower
• Outlasts Rubber
• Virtually Indestructible

Product Features:

• Revised Design to Allow GM LS & Gen-V LT Engines to Be Installed in 1973-1987 Chevy/GMC C10/C20 Series 2WD Truck & 1973-1982 Blazer/Jimmy 2WD
• Welded Steel Construction w/ Black Finish for Light Weight, Durability & Corrosion Protection
• Replaces Original Frame Stands
• Use with Clamshells 71221018HKR for GM LS Engines or Clamshells 71221019HKR with Gen-V LT Engines – Both Style Engines Use Polyurethane Inserts 71221016HKR (black) or 71221017HKR (red), and bolts 71223015HKR
• Modular Design of Engine Mounts Allows Engine Change from GM LS to Gen-V LT Engine by Changing Clamshells (Polyurethane Inserts, Bolts, and Crossmember are the Same for Both Style Engines)
• Works with GM LS Swap Pans: 302-1, 302-2, 302-3 & Gen-V LT Swap Pan 302-20
• Allows Use of Low Mount A/C – for Both Truck Style Accessories & LSA Supercharged Engine
• Use with Transmission Crossmembers: BHS548 (4L60E/4L65E/4L70E/4L75E/6L80), BHS549 (4L80E/4L85E), or BHS550 (T56/T56 Magnum)
• Works with Hooker Cast Exhaust Manifolds – Additional Headers Will Also Be Available

Product Features:

• Can be used for a variety of GM vehicle applications and LS/LT swaps that utilize the common 2292 aftermarket mounts
• Heavy duty 11-gauge steel construction is over 50% thicker than common aftermarket mounts
• Dowels allow halves to be easily aligned
• No need to drill rivets from existing shell
• Durable powder coated finish
• For use with Hooker BlackHeart Polyurethane Inserts – P/N’s 71221014HKR (Black) or 71221015HKR (Red) – Sold Separately
• Sold individually (Consisting of one upper and one lower plate, Two required per vehicle)

Product Features:

• Can be used for aftermarket poly mounts or OEM rubber (Rubber Mounts are for GM 4th Gen F-Body)
• Class 10.9 for strength
• Zinc plated for corrosion resistance
• Includes 2 flange head bolts and 2 flange nuts