1980 Dodge D150 Drivetrains
More 1980 Dodge D150 Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1980 Dodge D150, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1980 Dodge D150 Drivetrains
Driveworks – Taper Bearing Cup (Part No.S-HM-88610)
from
$6.49
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – Pinion Nut (Part No.33142)
from
$10.99
Pinion nut for Chrysler 7.25″, 8.0″ IFS, 8.25″, 8.75″ fine spline, 9.25″ front & rear, 7/16″ x 14.
Product Features:
See More
Product Features:
- Pinion nut for Chrysler 8.0″ IFS, 8.25″, 8.75″ with 29 spline pinion and 9.25″ rear
- 7/8″ x 14 thread
Needa Parts – Rubber Differential Plug Chrysler 2008-2000 (sold by each) (Part No.090-062)
from
$10.99
Our Differential Cover Plug is manufactured from high quality rubber. Durable design ensures a long service life.
Product Features:
See More
Product Features:
- Direct replacement for a proper fit every time
- Conveniently available in packs of different quantities
- Easy to install
- Dorman’s Differential Cover Plugs are constructed to strict engineering quality standards
MOOG Driveline Products – Universal Joint Strap Kit (Part No.316-10)
from
$10.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.
Product Features:
See More
Product Features:
- For U-Joints 316 & 458
- Contains two 1.54″ bolt center clamps and four 1/4-28 x 5/8″ cap screws
Yukon Gear – Cross Pin Shaft For Standard Open Chrysler 9.25" (Part No.33311)
from
$46.99
Cross pin shaft for standard open Chrysler 9.25″, .860″ diameter. Will not fit posi!
Product Features:
See More
Product Features:
- Cross pin shaft for Chrysler 9.25″
- Fits standard open differentials only
- 0.860″ diameter
Rugged Ridge – Locking Hub (Part No.15001.18)
from
$286.99
Approved as original equipment by vehicle manufacturers and militaries world wide, these tough hubs are built to last. A hardened nylon center is used instead of metal to keep you moving in the rare case of a hub failure. The only way to repair it is to r
Product Features:
See More
Product Features:
- Impact Resistant Nodular Iron
- Corrosion Resistant
- Better 4WD Performance
- Better Fuel Economy
- Easy Install
Dorman – Differential Pinion Yoke Assembly (Part No.697-541)
from
$231.99
A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.
Product Features:
See More
Product Features:
- Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
- Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
- Durable construction – designed and manufactured to strict specifications for reliable performance
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
USA Standard Gear – Spartan Locker For Chrysler 8.25" With 27 Spline Axles, Includes Heavy-Duty Cross Pin Shaft (Part No.17037)
from
$829.99
The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.
Product Features:
See More
Product Features:
- Fits Chrysler 8.25″ with 27 spline axles
- Made from 9310 steel for added strength
- Replaces the spiders in a standard carrier case
Pro-King – Clutch Pack (Part No.723A119)
from
$122.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
National – Multi Purpose Seal (Part No.8516N)
from
$17.29
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Low swell in hydrocarbon fluids
- Design type: spring loaded; multi-lip
- Provides good low temperature capability
- Temperature range: -40°F to 225°F; -40°C to 107°C
- Delivers quality and reliable performance for every type of repair
Dorman – Spindle Washer – I.D. 19.1mm O.D. 41.6mm Thickness 2.6mm (sold by each) (Part No.618-061)
from
$14.29
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Driveworks – Taper Bearing Cone (Part No.S-M-86649)
from
$8.79
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – R1561Tv Rear Axle Bearing And Seal Kit (Part No.10002)
from
$92.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1561TV axle bearing and seal kit, for Ford and Dodge, TorringtonBrand, 2.985″ OD, 1.700″ ID. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Fits Ford and Dodge applications
- Includes axle bearing and seal
- Torrington Brand
- Services one side
- 2.985″ O.D.
- 1.700″ I.D.
Yukon Gear – C/Clip (Part No.33083)
from
$8.99
C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.
Product Features:
See More
Product Features:
- c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
- .150″ thick
Yukon Gear – Flange Yoke For Chrysler 9.25" (Part No.41012)
from
$263.99
Yukon flange yoke for Chrysler 9.25″. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Chrysler 9.25″ rear
- 29 spline
- Round companion flange
Yukon Gear – Six Piece Side Gear And Thrust Washer Kit For Chrysler 8" And 9.25" (Part No.33278)
from
$98.99
Six piece side gear thrust washer kit for Chrysler 8″ and 9.25″.
Product Features:
See More
Product Features:
- Side gear thrust washer kit
- Fits Chrysler 8″ and 9.25″
Motive Gear – Ring Gear Bolt (Part No.14066913)
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)
from
$22.79
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.3780 INCH / 35 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- COMPLETE MOUNT
Yukon Gear – Bearing Install Kit For ’75 And Newer Chrysler 8.25" Differential (Part No.11004)
from
$234.99
Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.
Product Features:
See More
Product Features:
- Fits 1976 and up Chrysler 8.25″
- Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve , marking compound and brush.
Yukon Gear – Rubber Fill Plug For Chrysler (Part No.33463)
Felpro – Differential Cover Gasket (Part No.RDS 55073)
from
$9.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
USA Standard Gear – Open Spider Gear Set For Chrysler 9.25", 31 Spline (Part No.39004)
from
$209.99
Product Features:
See More
- Fits Chrysler 9.25″ rear with open differential
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Pro-King – Differential Internal Nest Kit (Part No.723A717)
from
$227.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
National – Bearings (Part No.M88010)
from
$10.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Standard Open Spider Gear Kit For ’96 And Older 8.25" Chrysler With 27 Spline Axles (Part No.16002)
from
$301.99
Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fit Chrysler 8.25″ open differntial with 27 spline axles
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Yukon Gear – 9.25" Chrysler, Dana 60 Semi-Float X/P Bolt, 80 & Up, 5/16" Head, Tapered Shoulder (Part No.33238)
Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (sold by each) (Part No.615-072)
from
$3.99
This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Yukon Gear – High Performance Ring & Pinion Gear Set For ’04 & Down Chrysler 8.25" In A 3.21 Ratio (Part No.24225)
from
$479.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.
Product Features:
See More
Product Features:
- Fits Chrysler 8.25″
- 8.25″ ring gear diameter
- 27 spline pinion
- 10 ring gear bolts
- 3.21 ratio
Popular 1980 Dodge D150 Drivetrains Categories
1980 Dodge D150 Drivetrains
You count on your 1980 Dodge D150 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 267 Drivetrains ranging in price from $1.99 to $2,364.99, you’re sure to find everything you need for your 1980 Dodge D150.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 17 different brands like National, Felpro, and Yukon Gear. 1980 Dodge D150 Drivetrains start as low as $1.99!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 1,236 extensive product reviews on 1980 Dodge D150 Drivetrains. Some of the top-rated Drivetrains products we carry are Axle Repair Bearing with 2.5 stars and Differential Carrier Gear Kit with 3.7 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1980 Dodge D150 below to get started!
Top-Rated Drivetrains Brands For Your 1980 Dodge D150
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1980 Dodge D150 running right for years to come. In our inventory you’ll find brands like National, Felpro, Yukon Gear, and even more.
Popular Needa Parts Drivetrains
You’ll find popular Needa Parts brand products across Differentials. All are waiting to get your 1980 Dodge D150 back on the road. Some of the top-rated Needa Parts products in these categories are:
Top-Rated National Drivetrains
If National are what you’re looking for, our inventory holds plenty. We stock National brand Drivetrains for your 1980 Dodge D150, and some of our most reviewed National parts include:
FAQs for 1980 Dodge D150 Drivetrains
What are the most purchased Drivetrains for the 1980 Dodge D150?
Out of 267 Drivetrains for the 1980 Dodge D150, the most popular in our inventory are:
What are the top-rated 1980 Dodge D150 Drivetrains?
Top-rated Drivetrains for your 1980 Dodge D150 based on customer reviews/ratings are:
