1980 Chevrolet Monte Carlo Performance Exhaust Products

Essential 1980 Chevrolet Monte Carlo Performance Exhaust Products

Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound (Part No.942441)

40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound

from

$133.99
This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – 40 Series Muffler, 2in Offset Inlet 2in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.942043)

40 Series Muffler, 2in Offset Inlet 2in Offset Outlet, Non-Reversible, Aggressive Sound

from

$133.99
This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Dynomax – Super Turbo Muffler: Di Fit Aluminized Steel, 14" L, 2.25" In, 2.5" Out, Oval (Part No.17667)

Super Turbo Muffler: Di Fit Aluminized Steel, 14" L, 2.25" In, 2.5" Out, Oval

from

$106.99
Dynomax Super Turbo performance mufflers’ exclusive, patented, flow director design channels exhaust flow, and eliminates turbulence on most applications. The large internal flow tubes improve exhaust flow, and reduce backpressure. Each muffler uses fiberglass matting technology to absorb unwanted interior resonance, while maintaining a mellow performance tone.

Product Features:
  • Large internal flow tubes improve exhaust flow and reduce backpressure
  • Dyno proven to flow up to 700 SCFM
  • Exclusive patented flow director channels exhaust flow and eliminates turbulence on most applications.
  • Fiberglass matting technology absorbs unwanted interior resonance but maintains a mellow tone
  • 1.75-inch to 3-inch inlet / outlet configurations
See More

Flowmaster Inc. – 50 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, Non-Reversible, Moderate Sound (Part No.842553)

50 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, Non-Reversible, Moderate Sound

from

$175.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound (Part No.8042441)

40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound

from

$123.99
The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – 50 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Moderate Sound (Part No.942051)

50 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Moderate Sound

from

$154.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – 70 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, 22in long, Non-Reversible, Mild Sound (Part No.52573)

70 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, 22in long, Non-Reversible, Mild Sound

from

$221.99
The 70 series utilizes Flowmaster’s patented Delta Flow technology and an enlarged case for improved sound control along with mileage and power gains. Perfect for use on trucks, SUV’s, RVs, tow vehicles and high performance street cars where space allows. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

MagnaFlow – Street Series Cat-Back Performance Exhaust System (Part No.16727)

Street Series Cat-Back Performance Exhaust System

from

$1260.00
The MagnaFlow 2006-2007 Chevrolet Monte Carlo Street Series Cat-Back Performance Exhaust System brings out the personality of your 5.3L 2006-2007 Chevrolet Monte Carlo with our signature resonant, powerful engine tone and dyno-proven performance. Thanks to its fast-flowing, mandrel bent 2.5in. main piping and 3 Straight-Through mufflers ending in a Dual Split Rear exit with 4in. Polished Welded-On Double Wall Angle Cut Rolled Edge tips, this Chevrolet Monte Carlo exhaust kit has the performance chops to match its sporty sound and appearance. Upgrade your ride to the next level with an exhaust that has the pipes to put other Chevrolet Monte Carlo’s to shame. With this system your vehicle will be producing Moderate exterior and Mild interior sound levels while leaving other cars and trucks feeling envious at every stoplight. Exhaust kit 16727 features a cat-back layout that replaces your ride’s stock exhaust components from near the catalytic converter on back. Extensive 3D scanning during development has resulted in a direct-fit design that you can easily install yourself. 16727 is produced using CNC precision robotic manufacturing techniques and is backed by MagnaFlow’s 1-year limited finish warranty and limited lifetime construction warranty.

Product Features:
  • Dyno-proven performance
  • Durable corrosion-resistant stainless steel construction
  • CNC precision robotic manufacturing techniques
See More

Dynomax – 89017 Exhaust System Kit (Part No.89017)

89017 Exhaust System Kit

from

$259.99
Give your vintage vehicle’s exhaust system an upgrade with a DynoMax® dual header kit. Designed to attach with OE headers, it features a special reducer that allows for a variety of mounting options.

Product Features:
  • COMPATIBILITY — Designed for 1978-1987 midsize sedans such as Oldsmobile Cutlass, Chevrolet Monte Carlo, Buick Regal and Pontiac Grand Prix; see product information for compatibility and engine spec
  • BUILD IT YOURSELF — Design and custom fabricate your own exhaust system with this kit that attaches to OE headers
  • FLEXIBLE MOUNTING — Special reducer design allows for a variety of mounting options
  • IMPROVED FLOW CAPACITY — Smooth bends improve flow capacity over traditional bends
  • SPECS — Extra-long tailpipes with side exits with a full 2.25-in. diameter; tail pipes exit on each side of vehicle at rear bumper
  • COMPLETE SOLUTION — Includes all the necessary clamps, hangers, flanges, gaskets, mounting hardware, intermediate, extension and tail pipes
  • PREMIUM MATERIALS – Made from quality aluminized steel for durability and long life
  • BETTER TOGETHER — Complete your system with premium DynoMax mufflers and DynoMax accessories for a complete performance exhaust system
  • WARNING — Not legal for use on pollution-controlled motor vehicles; headers are for racing use only and not intended or applicable for highway use
See More

Edelbrock – Exhaust Manifold Gasket Set for Chevrolet (Part No.7204)

Exhaust Manifold Gasket Set for Chevrolet

from

$24.99
Product Features:
  • 0.0625 in. Thickness
  • 1.50 in. x 1.50 in. Port Size
  • For SB Chevy
  • Black Color
  • Two Piece Configuration
See More

Flowtech – Real-Seal; Header Gasket (Part No.99150AFLT)

Real-Seal; Header Gasket

from

$85.39


Product Features:
  • Water/Weather Resistant
  • Re-Useable
  • Will Not Burn Or Blow Out
  • Suitable For Port-Matching
  • Made In USA
See More

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5911)

Ultra Seal: Exhaust Gasket Set

from

$38.59
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:
  • Has A Steel Core With Graphite Facing
  • Graphite Facing Has Excellent Thermo-conductivity
  • Can Be Trimmed If Necessary For Modified Port App
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1410)

Exhaust Manifold Gasket Set

from

$37.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Performance Exhaust Gasket Set for Enhanced Sealing and Durability (Part No.150B)

Performance Exhaust Gasket Set for Enhanced Sealing and Durability

from

$20.99
Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.

Product Features:
  • Manufactured from high-temperature acrylic blend exhaust material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
  • Resists Deteriorating
  • Provides Excellent Torque Retention
See More

Hooker Headers – Super Competition Header Gasket (Part No.10809HKR)

Super Competition Header Gasket

from

$23.29
Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.

Product Features:
  • Tear Resistant
  • Precisely Cut To Match Header
See More

Flowtech – Real-Seal; Header Gasket (Part No.99153FLT)

Real-Seal; Header Gasket

from

$85.39


Product Features:
  • Water/Weather Resistant
  • Re-Useable
  • Will Not Burn Or Blow Out
  • Suitable For Port-Matching
  • Made In USA
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1400)

Exhaust Manifold Gasket Set

from

$33.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1411)

Exhaust Manifold Gasket Set

from

$42.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Dynomax – Manifold/Header (Part No.85121)

Manifold/Header

from

$119.99
Manifold/Header

Hooker Headers – Competition Header (Part No.2455-2HKR)

Competition Header

from

$951.99
Competition Header

Hooker Headers – LS1 Swap Headers for 66-72 Chevelle, El Camino, Monte Carlo & Sprint (Part No.2455-1HKR)

LS1 Swap Headers for 66-72 Chevelle, El Camino, Monte Carlo & Sprint

from

$552.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Flowtech – High-Performance Headers with Fuel Economy and Leakproof Design (Part No.11100FLT)

High-Performance Headers with Fuel Economy and Leakproof Design

from

$227.99


Product Features:
  • Fuel Economy From The Engine
  • Leak Test For Max Performance
  • Mandrel-Formed Power Plenum
  • Leakproof O-Ringed Port Seals
  • Include All Mounting Hardware
See More

Hooker Headers – Competition Header (Part No.2451-2HKR)

Competition Header

from

$895.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Flowtech – Standard Header with Enhanced Fuel Efficiency and Leakproof Technology (Part No.11108FLT)

Standard Header with Enhanced Fuel Efficiency and Leakproof Technology

from

$223.99


Product Features:
  • Fuel Economy From The Engine
  • Leak Test For Max Performance
  • Mandrel-Formed Power Plenum
  • Leakproof O-Ringed Port Seals
  • Include All Mounting Hardware
See More

Hooker Headers – Competition Header (Part No.2451-1HKR)

Competition Header

from

$619.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Hooker Headers – LS Cast Iron Exhaust Manifold (Part No.8501-3HKR)

LS Cast Iron Exhaust Manifold

from

$576.99
LS Cast Iron Exhaust Manifold

Hooker Headers – Competition Header (Part No.2466-1HKR)

Competition Header

from

$668.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

Flowmaster Inc. – Header 409S – 4-1 One piece – 3.00 in. Ball and Socket Flange Outlet – Pair (Part No.814110)

Header 409S - 4-1 One piece - 3.00 in. Ball and Socket Flange Outlet - Pair

from

$951.99
Flowmaster’s Scavenger Series Elite long tube headers are designed to replace the restrictive factory cast iron manifolds. These high quality headers are manufactured from stainless steel and are ceramic coated for maximum durability. They feature 1-5/8 in. primary tubes, 3/8 in. thick flanges and incorporate Flowmaster’s popular 3 in. ball flange collector connections ensuring a leak free installation. Scavenger Series Elite long tube headers deliver maximum performance and are suited to the enthusiast who wants the best. Like all Flowmaster products the benefits include improved throttle response, power and engine efficiency. Designed for an easy fit these headers include gaskets and necessary hardware for easy installation. Fits D port cylinder heads including ZZ4 crate engines. Does not fit 1967 to 1969 Camaro’s with air conditioning. Will fit most angle plug heads including factory Chevrolet bow tie heads. Requires removal or modification of locking steering columns if equipped. Installation requires new left side air conditioning bracket. For 1979 and later vehicles with short compressors the stock bracket can be used. This product is legal only for off highway use except in California or states that have adopted California emission standards, racing use or for use on pre emission controlled motor vehicles and motor vehicle engines and pre 1966 domestic vehicles certified to California standards, pre 1968 domestic vehicles certified to federal standards and all pre 1968 foreign vehicles, per the application guide.

Product Features:
  • Stainless steel construction
  • Ball & socket collector connections
  • Dyno tuned for maximum performance
  • High temperature ceramic coated
  • 0.375 thick laser cut flanges
See More

1980 Chevrolet Monte Carlo Performance Exhaust Products

Maybe you’re in the middle of a full rebuild of that 1980 Chevrolet Monte Carlo. Maybe you just need a couple of Performance Exhaust Products. Either way, Advance Auto Parts has 23 different Performance Exhaust Products in our inventory ranging from $20.99 to $951.99. That means you can find the exact parts or products you need to keep that 1980 Chevrolet Monte Carlo running smoothly.

Performance Exhaust Products are only as good as their brand. We stock 7 different brands to make sure you have plenty of trusted parts to choose from for your 1980 Chevrolet Monte Carlo. Mr. Gasket, Hooker Headers, and FEL-PRO Performance are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Exhaust Products for your 1980 Chevrolet Monte Carlo, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 47 reviews in this category, some of the top rated parts include 40 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Aggressive Sound with 3.3 stars and Standard Header with Enhanced Fuel Efficiency and Leakproof Technology with 4.7 stars.

So if you’re in the market for aftermarket Performance Exhaust Products to keep your 1980 Chevrolet Monte Carlo rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Exhaust Products Brands To Make Your 1980 Chevrolet Monte Carlo Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1980 Chevrolet Monte Carlo demands trusted brand parts and products to keep it running. Many trusted brands of Performance Exhaust Products make up Advance Auto Parts’ inventory, and all are ready to help make your Monte Carlo the best it can be. Be sure to browse some of our top Performance Exhaust Products brands and parts.

Popular FEL-PRO Performance Performance Exhaust Products

We carry FEL-PRO Performance parts in our stock across Performance Exhaust Manifold Gaskets categories, plus more. For a 1980 Chevrolet Monte Carlo, our most popular FEL-PRO Performance Performance Exhaust Products include:
Exhaust Manifold Gasket Set
from $31.49
(2)
Exhaust Manifold Gasket Set
Performance Exhaust Manifold Gaskets

FAQs for 1980 Chevrolet Monte Carlo Performance Exhaust Products

What are the most purchased Performance Exhaust Products for the 1980 Chevrolet Monte Carlo?

Out of 23 Performance Exhaust Products for the 1980 Chevrolet Monte Carlo, the most popular in our inventory are:
Aluminum Exhaust Gasket: High-Heat Resistant, Easy Removal
from $42.99
This product is not rated
Aluminum Exhaust Gasket: High-Heat Resistant, Easy Removal
Performance Exhaust Manifold Gaskets
High-Performance Small Block Chevy Long Tube Headers
from $283.99
(4)
High-Performance Small Block Chevy Long Tube Headers
Performance Exhaust Headers
Exhaust Gasket Set
from $30.19
This product is not rated
Exhaust Gasket Set
Performance Exhaust Manifold Gaskets

What are the top-rated 1980 Chevrolet Monte Carlo Performance Exhaust Products?

Top-rated Performance Exhaust Products for your 1980 Chevrolet Monte Carlo based on customer reviews/ratings are:
40 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Aggressive Sound
from $133.99
(4)
40 Series Muffler, 2in Offset Inlet 2in Center Outlet, Non-Reversible, Aggressive Sound
“This muffler was easy to install. The only bad thing was that it was 4 inches shorter than the orignal one. So I had to ad a four inch peice of 2 inch”
Aero Chamber Muffler
from $120.99
(2)
Aero Chamber Muffler
“I like a certain amount of old school correctness in the aftermarket parts on my 1970 Bronco. I purchased the Hooker Dual Exhaust setup with Hooker A”