Name: Performer-Plus Camshaft Kit for 1957-86 Small-Block Chevrolet
Brand: Edelbrock
SKU: 2103
Price: 334.99 USD
Rating: 5.0 (1 reviews)

from

$334.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$322.99

Edelbrock part #2703 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thro

Product Features:

Idle-5500 RPM Range
Dual Plane Type-4150 Style Flange
3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
Satin Finish
Non-EGR W/ Oil Fill Tube

from

$31.99

Edelbrock part #6998 Front Timing Cover Gasket set for Big-Block Chevy. Includes front cover gasket and front seal.

Product Features:

Includes replacement timing cover and water pump gaskets and the crank oil seal for big block Chevrolet engines
Features a tough, scuff-resistant silicone rubber coating
Helps in sealing without the engine warming up
Reduces fluid migration through the gasket
Resists fatigue

from

$189.99

Product Features:

Case-Hardened Tubing
Welded Ends
5/16 in. Diameter
Use with or without Hardened Steel Guideplates

from

$32.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$75.99

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

Chrome plated
Grade 8
12-point head
AN washers with no exposed shoulder for a professional appearance

from

$42.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$126.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
O.D.: 1.254″, I.D.: .880″
Single valve springs with damper
Approximately .490″ max lift at recommended installed height

from

$23.79

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

Fits Chevy engines
Includes a 1/2 inch NPT threaded hole for by-pass hose
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$128.99

Product Features:

Provides excellent sealing and conformability
Releases+N747 clean without sticking, if the engine needs to be disassembled
Perfect companion for Edelbrock cylinder heads and intake manifolds
Does not include end seals
Use of a silicone sealant in place of end seal is recommended

from

$339.99

Torque Converter – Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$17.79

Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$475.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$258.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$42.49

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

Advance the cam for increased torque and horsepower
Tune your powerband for more end torque or increase top end horsepower
Includes (4) offset bushings and (1) 0 degree bushing
Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
Increase Top-End Horsepower

from

$29.99

Product Features:

Timing Chain Only

from

$26.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$63.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
Not intended for use in emission controlled vehicles.

from

$22.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$29.49

Molded rubber gaskets are reusable, great for engines that require valve lash maintenance. These gaskets feature Nitrile material for long life, solid steel carrier for strength and rigidity. Incorporates compression limiters to prevent fastener over-tightening.

Product Features:

Features Nitrile Rubber Material For Long Life
Molded Rubber Gaskets Are Reusable
Ideal For Engine Requiring Valve Lash Maintenance

from

$830.99

Product Features:

Made of aluminum with a natural finish
100cc chambers with 290cc intake ports
2.19 in. intake and 1.88 in. exhaust valves
Bare Cylinder Head
Standard intake and exhaust port location

from

$958.99

The Edelbrock #607519 Performer cylinder head is designed for 302, 327, 350 and 400 cid small-block Chevy engines up to 1986. This cylinder head includes your choice of 64cc (In order to retain stock compression ratio on 1970 and earlier small-blocks) or

Product Features:

Complete Single For Hydraulic Flat Tappet
70cc Combustion Chamber Volume
185cc Intake/65cc Exhaust Runner Volume
2.02 in. Intake/1.6 in. Exhaust Valve Diameter
0.562 in. Deck Thickness

from

$412.99

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Chevrolet V8 265-400 applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
Designed for high performance street and race engines
Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
Additional clearance, up to 1.650″ O.D. valve spring

from

$213.99

These Magnum Roller Rocker Arms for Chevy V8 265-400 and V6 200-262 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.52 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed

Product Features:

Roller tip reduces friction while stiff design and superior ratio accuracy yield more effective valve lift
For applications with less than 350 lbs. of open spring pressure
Constructed from 8620 chromemoly steel, a superior material that will not flex and ensures maximum lift
Ultimate street roller rocker arm designed for serious performance enthusiasts

from

$73.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

1980 Chevrolet C10 Performance Engines

More 1980 Chevrolet C10 Performance Engines

Essential 1980 Chevrolet C10 Performance Engines

Edelbrock – Performer-Plus Camshaft Kit for 1957-86 Small-Block Chevrolet (Part No.2103)

Edelbrock – Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy (Part No.2703)

Edelbrock – Front Timing Cover Gasket Set #6998 For Big-Block Chevy, With Front Seal (Part No.6998)

Edelbrock – Pushrod Set for S/B Chevy (Part No.9630)

Edelbrock – Intake Manifold Gasket for 1965-1990, Oval port 396-402-454 B/B Chevy (Part No.7203)

Mr. Gasket – Intake Bolt Kit (Part No.5003)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2918)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Competition Cams – Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height (Part No.981-16)

Spectre – Water Neck; Chevy Late Model (Part No.4730)

Edelbrock – Engine Gasket Set (Head / Intake / Exhaust / Valve Cover) for Chevrolet (Part No.7361)

B & M – Tork Master 2400 (Part No.20404)

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4377)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Edelbrock – Water Pump Big-Block Chevy Standard/Long in Polished Finish (Part No.8861)

Competition Cams – CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA (Part No.12-250-3)

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Edelbrock – TIMING CHAIN (Part No.7844)

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1803)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1886)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1640)

Mr. Gasket – Valve Cover Gasket Set (Part No.585G)

Edelbrock – Performer Big-Block Chevy Oval Port Hydraulic Flat Tappet Springs (Part No.60489)

Edelbrock – RPM Small-Block Chevy Cylinder Head SBC 70cc Flat Tappet Cam Polished (Part No.607519)

Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Chevrolet Small Block w/ 3/8" Stud (Part No.19002-16)

Competition Cams – MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST (Part No.1412-16)

Mr. Gasket – Ultra Seal: Cylinder Head Bolts (Part No.941G)

Popular 1980 Chevrolet C10 Performance Engines Categories

1980 Chevrolet C10 Performance Engines

Performance Engines Brands To Make Your 1980 Chevrolet C10 Last

Popular B & M Performance Engines

Top 1980 Chevrolet C10 Performance Engines from Mr. Gasket

FAQs for 1980 Chevrolet C10 Performance Engines

What are the most purchased Performance Engines for the 1980 Chevrolet C10?

What are the top-rated 1980 Chevrolet C10 Performance Engines?

More Popular Parts for All Makes