1979 Dodge Magnum Differentials

Dana 44 & 9.25 Chrysler TracLoc clutch kit.

Product Features:

• Clutch kit
• Fits Dana Spicer 44 and Chrysler 9.25″ Trac Loc positraction

Toyota wheel seal for ’80-’97 Full float Landcruiser outer rear, ’86-’95 dually pick-up.Yukon Mighty seal.

Product Features:

• Fits Chrysler 9.25″ rear
• Chrome

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: spring loaded; multi-lip
• Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
• Resistance to EP lubricants
• Low swell in hydrocarbon fluids
• Delivers quality and reliable performance for every type of repair

Model 35 (standard Open & TracLoc) 8.25″ Chrysler TracLoc cross pin bolt.

Product Features:

• Cross pin bolt for AMC Model 35 with c-clip axles

This differential ring and pinion directly replaces the original equipment on specific vehicle years, makes and models.

Product Features:

• Direct replacement – this ring and pinion set matches the fit and function of the original components on certain vehicle applications
• Effective fix – eliminates grinding and whining from failed original bearings
• Thoroughly tested – vehicle try-on testing and rigorous quality control measures ensure longevity
• Trustworthy quality – backed by team of designers and engineers in the United States

Differential carrier side bearing screw adjuster for Chrysler 7.25″ and 8.25″.

Product Features:

• Side adjuster
• Fits Chrysler 7.25″ and 8.25″

Product Features:

• MINI INSTALL KIT CHRYSLER 9.25 9 1/4″

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Chrysler 7.25″ rear
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

8.25″ Chrysler pinion gear thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits Chrysler 8.25″

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1976 and up Chrysler 8.25″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Chrysler 9.25″
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
• Fits Yukon Dura Grip

Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Chrysler 8.25″ open differntial with 27 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

• FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations.
• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

Yukon flange yoke for Chrysler 9.25″. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler 9.25″ rear
• 29 spline
• Round companion flange

Cross pin shaft for Chrysler 7.25″.

Product Features:

• Cross pin shaft
• Fits Chrysler 7.25″

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M804010 race
• All steel construction

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

• Side adjuster for Chrysler 9.25″ rear

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

Product Features:

• Dura Grip positraction carrier case
• Does not include spider gears
• Fits Chrysler 9.25″ rear

Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

Product Features:

• Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
• 3/8″ x 24 thread
• .866″ long

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• MASTER KIT CHRYSLER 8.25″

Crush Sleeve for Chrysler 8″ & 9.25″ rear. Approx 0.630″ long.

Product Features:

• Crush sleeve for Chrysler 8.0″ IFS and 9.25″ rear, also Ford 9″ with aftermarket Daytona pinion support
• 0.630″ tall

Pinion nut for Chrysler 300, CHARGER, MAGNUM.

Product Features:

• Pinion nut
• Fits Chrysler C198 and C210

Side gear thrust washer for 7.25″ Chrysler.

Product Features:

• Side gear thrust washer kit
• Fits Chrysler 7.25″

M804049 set-up bearing (one bearing). No return.

Product Features:

• Set up bearing
• Fits HM804049 pinion bearing
• Easily slips on and off pinion journal to allow for pinion depth adjustment

Product Features:

• KIT SHIM