1978 Mercury Zephyr Differentials

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon-Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 8″ with 28 spline axles
• Trac Loc positraction
• Clutch style positraction
• Street design
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt. 7/16″ head, .925″ long.

Product Features:

• Ring gear bolt for Ford 8″ and 9″
• For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
• 7/16″ head
• .925″ long

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features:

• AXLE SHAFT 8.8″ 28 SPL. 29 1/4″ 79-93 MUSTANG L & R

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits Ford 8″ with aftermarket positraction
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 8″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Yukon standard open spider gear kit for 7.5″ Ford with 28 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Ford 7.5″ open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

8″ Ford pilot bearing retainer.

Product Features:

• Pilot bearing retainer for Ford 8″

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

8″ TracLoc case, bare, 2 or 4 PIN, 4 TAB clutch design.

Product Features:

• Trac Loc positraction carrier case
• Does not include spider gears
• Fits Ford 8″

Sealed Power parts provide innovative designs, use leading-edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Product Features:

• Steel-backed Babbitt lining material
• Used in automotive and high-performance
• Babbitt is designed to perform under extreme loads without damaging other engine parts
• Babbitt is more environmentally friendly than other material
• ISO & QS certified manufacturing

Product Features:

• FRD 10BL 7.5 R/P 4.10 MG

Product Features:

• Friction plate
• Fits Ford 8″ and 9″ Trac Loc positraction

7.5″ Ford notched cross pin shaft. Not Auburn gear. This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers.

Product Features:

• Notched cross pin shaft for Ford 7.5″
• 3.73 and up ratios
• Not compatible with Spartan Locker or Powertrax Lock Right

9.25 Chrysler FRONT PINION KIT , 03 & UP DODGE TRUCK .

Product Features:

• Pilot bearing
• Fits Ford 8″

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Product Features:

• Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
• 0.030″ thick

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M88010 race
• All steel construction

7.5″ Ford cover gasket.

Product Features:

• Cover gasket
• Fits Ford 7.5″

Good used Yukon yoke for Ford 8″ with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 8″
• 25 spline
• 1310 u-joint size
• Outside snap ring design
• 3.219″ snap ring span
• 1.062″ cap diameter
• U-bolt style

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

8″ Ford O-ring.

Product Features:

• Pinion support o-ring
• Fits Ford 8″

High-quality Differential Component Shim

Product Features:

• SHIM KIT FITS-8.25-F7.5-AMC20-GM0

Product Features:

• INTERNALS FORD 7.5

7.5″, 8″, 8.8″, 9″, 10.25″ Ford REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Ford 7.5″, 8.8″, 9″ and 10.25″

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Pinion support bolt for 8″ and 9″ Ford.

Product Features:

• Pinion support bolt for Ford 8″ and 9″
• 3/8″ x 24 thread
• 1.0″ long