1978 Dodge Charger Drivetrains
More 1978 Dodge Charger Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1978 Dodge Charger, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1978 Dodge Charger Drivetrains
Yukon Gear – Replacement Clutch Set For Dana 44 Powr Lok, Aggressive (Part No.16151)
from
$232.99
Product Features:
See More
- Clutch kit
- Fits Dana Spicer 44 and Chrysler 8.75″ Powr Lok
- Aggressive design
Yukon Gear – Pinion Depth Shim Kit For Toyota8", GM 7.5", 8.2" & 12 Bolt Truck (Part No.55064)
from
$39.99
8″ Toyota, 7.5″ GM, 8.2″ GM, 12T, pinion shim set, & Mazda truck.
Product Features:
See More
Product Features:
- Pinion depth shim kit for Toyota 7.5″, 8″ and V6
MOOG Driveline Products – Universal Joint Strap Kit (Part No.316-10)
from
$10.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.
Product Features:
See More
Product Features:
- For U-Joints 316 & 458
- Contains two 1.54″ bolt center clamps and four 1/4-28 x 5/8″ cap screws
National – Multi Purpose Seal (Part No.224250)
from
$10.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Low swell in hydrocarbon fluids
- Design type: spring loaded; multi-lip
- Provides good low temperature capability
- Temperature range: -40°F to 225°F; -40°C to 107°C
- Delivers quality and reliable performance for every type of repair
Yukon Gear – Pinion Install Kit For Chrysler 8.75" (#41) Differential (Part No.13005)
from
$292.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″ ’41’ case
- Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.
National – Bearings (Part No.HM88649)
from
$21.79
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Replacement Trac Loc Carrier Case, Dana 60, 4.10 & Down (Part No.20043)
from
$509.99
Product Features:
See More
- Trac Loc positraction carrier case
- Does not include spider gears
- Fits Dana Spicer 60
- 4.10 and down ratio only
- ABS and non-ABS compatible
Yukon Gear – Positraction Clutch Guide (Part No.33352)
from
$8.99
Positraction clutch guide.
Product Features:
See More
Product Features:
- Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
- Compatible with Dura Grip positractions only
Yukon Gear – High Performance Ring & Pinion Gear Set For ’09 & Down Chrysler 9.25" In A 3.90 Ratio (Part No.24014)
from
$539.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon has an updated, proprietary, design that provides longer life and higher durability than the competition. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. We reccomend an OEM gear for van applications. This gear set is for ’09 and older applications only.
Product Features:
See More
Product Features:
- Fits 2010 and down Chrysler 9.25″ rear
- 9.25″ ring gear diameter
- 29 spline pinion
- 12 ring gear bolts
- 3.90 ratio
Yukon Gear – The Carrier Bearing Puller (Part No.56072)
from
$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
Yukon Gear – Chrysler 8.75 "89" Case Crush Sleeve (Part No.33092)
from
$17.99
Chrysler 8.75 “89” case Crush Sleeve. Approx 3.000″ long.
Product Features:
See More
Product Features:
- Crush sleeve for Chrysler 8.75″ ’89’ case
- 3.000″ tall
Driveworks – Tapered Roller Bearing (Part No.S-JLM-704610)
Yukon Gear – C/Clip (Part No.33083)
from
$8.99
C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.
Product Features:
See More
Product Features:
- c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
- .150″ thick
Yukon Gear – Steel Cover For Chrysler 9.25" Rear (Part No.32314)
Yukon Gear – Replacement Standard Open Spider Gear Kit For Dana 60 With 30 Spline Axles (Part No.16009)
from
$223.99
Yukon replacement standard open spider gear kit for Dana 60 with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fit Dana Spicer 60 open differential with 30 spline axles
- Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.
Motive Gear – Differential Carrier Gear Kit (Part No.C8.25BI)
Yukon Gear – Dana 50 Dana 60 Dana 70 & Dana 80 Roll Pin, 0.225" Dia, For X/P Shaft, 1.87" Lng (Part No.33327)
from
$7.99
Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.
Product Features:
See More
Product Features:
- Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
- 0.225″ diameter
- 1.870″ long
Pro-King – Differential Internal Nest Kit (Part No.723A717)
from
$227.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Driveworks – Camshaft Seal (Part No.S-99139)
Yukon Gear – 9.25" Chrysler Rear Cover Gasket (Part No.23002)
from
$12.99
9.25″ Chrysler rear cover gasket.
Product Features:
See More
Product Features:
- Cover gasket
- Fits Chrysler 9.25″ rear
Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)
from
$44.99
3 Qt. Penzoil 80W90 conventional gear Oil.
Product Features:
See More
Product Features:
- Includes three quarts of conventional oil
Yukon Gear – Pinion Nut For Dana 44 JK, 44HD, 60, 70, 70U, 70HD & Nissan Titan Rear 1 5/16" Nut 7/8" X 14 Thread (Part No.33144)
from
$7.99
Replacement pinion nut for Dana 44 JK, 44HD, 60, 70, 70U, 70HD & Nissan Titan rear. 1 5/16″ nut, 7/8″ x 14 thread.
Product Features:
See More
Product Features:
- Pinion nut for Jeep JK rear, Dana Spicer 44HD, 60, 70, 70U, 70HD and Nissan Titan rear
- 7/8″ x 14 thread
- 1 5/16″ socket
Pro-King – Differential Bearing Cup (Part No.742G256)
from
$8.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Yukon Gear – Differential Side Bearing Screw Adjuster For 9.25" Chrysler (Part No.33256)
from
$64.99
Differential side bearing screw adjuster for 9.25″ Chrysler.
Product Features:
See More
Product Features:
- Side adjuster for Chrysler 9.25″ rear
Motive Gear – Differential Pinion Seal (Part No.9316)
from
$16.49
Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o
See More
Yukon Gear – Six Piece Side Gear And Thrust Washer Kit For Chrysler 8" And 9.25" (Part No.33278)
from
$98.99
Six piece side gear thrust washer kit for Chrysler 8″ and 9.25″.
Product Features:
See More
Product Features:
- Side gear thrust washer kit
- Fits Chrysler 8″ and 9.25″
Yukon Gear – The Carrier Bearing Puller (Part No.56034)
from
$689.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
- Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications
Dorman – Spindle Washer – I.D. 23.0mm O.D. 38.0mm Thickness 3.6mm (sold by each) (Part No.618-017)
from
$3.49
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Popular 1978 Dodge Charger Drivetrains Categories
1978 Dodge Charger Drivetrains
You count on your 1978 Dodge Charger to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 191 Drivetrains ranging in price from $1.99 to $883.99, you’re sure to find everything you need for your 1978 Dodge Charger.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 13 different brands like National, Felpro, and Yukon Gear. 1978 Dodge Charger Drivetrains start as low as $1.99!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 994 extensive product reviews on 1978 Dodge Charger Drivetrains. Some of the top-rated Drivetrains products we carry are Bearings with 5.0 stars and Differential Carrier Gear Kit with 3.7 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1978 Dodge Charger below to get started!
Top-Rated Drivetrains Brands For Your 1978 Dodge Charger
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1978 Dodge Charger running right for years to come. In our inventory you’ll find brands like National, Felpro, Yukon Gear, and even more.
Popular Driveworks Drivetrains
You’ll find popular Driveworks brand products across Universal Joints. All are waiting to get your 1978 Dodge Charger back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Felpro Drivetrains
If Felpro are what you’re looking for, our inventory holds plenty. We stock Felpro brand Drivetrains for your 1978 Dodge Charger, and some of our most reviewed Felpro parts include:
FAQs for 1978 Dodge Charger Drivetrains
What are the most purchased Drivetrains for the 1978 Dodge Charger?
Out of 191 Drivetrains for the 1978 Dodge Charger, the most popular in our inventory are:
What are the top-rated 1978 Dodge Charger Drivetrains?
Top-rated Drivetrains for your 1978 Dodge Charger based on customer reviews/ratings are:
