1978 Checker Marathon Performance and Racing Products

Essential Performance and Racing Products for 1978 Checker Marathons

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Engine Timing Cover Gasket

from

$20.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Steel core gasket construction
  • Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
  • Not intended for use in emission controlled vehicles.
See More

B & M – Tork Master 2400 (Part No.20404)

Tork Master 2400

from

$339.99
Torque Converter – Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

Competition Cams – CAMSHAFT, SBC 295 BIG MUTHA THUMPR HYDRAULIC 1 EA (Part No.12-602-4)

CAMSHAFT, SBC 295 BIG MUTHA THUMPR HYDRAULIC 1 EA

from

$529.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1025)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$72.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

FAG US – CUP (Part No.LM48510)

CUP

from

$7.69
CUP

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1448)

Exhaust Manifold Gasket Set

from

$34.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$428.99
The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

from

$111.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)

PERFORMANCE REAR MAIN SEAL SET

from

$36.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – PERFORMANCE VALVE COVER GASKET SET (Part No.1602)

PERFORMANCE VALVE COVER GASKET SET

from

$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Die cut silicone rubber gaskets conform to out-of-flat covers
  • Great for on-again/off-again situations
  • Not intended for use in emission controlled vehicles.
See More

Accel – Supercoil (Part No.140001)

Supercoil

from

$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:
  • Oil Filled For Better Cooling
  • Optimized Low Resistance
  • Silicon Magnetic Steel E-Core
  • Higher Energy/Voltage Outputs
  • Quicker Starts
  • Improved Idle Quality
  • Resists Shock And Vibration
  • Resists Corrosion
See More

Edelbrock – Performer EPS Manifold w/Oil Fill Tube for Small-Block Chevy, Black Finish (Part No.27033)

Performer EPS Manifold w/Oil Fill Tube for Small-Block Chevy, Black Finish

from

$445.99
Edelbrock part #27033 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thr

Product Features:
  • Idle-5500 RPM Range
  • Dual Plane Type-4150 Style Flange
  • 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
  • Black Powder Coated Finish
  • Non-EGR W/ Oil Fill Tube
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1818)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1819)

PERFORMANCE OIL PAN GASKET SET

from

$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

B & M – Transpak For 65-87 TH400 Transmission (Part No.20228)

Transpak For 65-87 TH400 Transmission

from

$141.99
The B&M Transpak has all the features in the Shift Improver Kit, plus it provides additional driver manual control. Retain full automatic features and standard shift points with selector in Drive.

Product Features:
  • Recalibrate Auto. Transmission
  • Optimum Performance
  • Select Your App. Mode
  • Improves Transmission Life
  • Trans. Removal Not Required
  • Downshift At Any Speed
  • Great For Trailer Towing
  • For Heavy Loads Driving Downhill
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Accel – Custom Fit Spark Plug Wire Set (Part No.8848)

Custom Fit Spark Plug Wire Set

from

$122.99
These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:
  • 8.8mm Graphite Suppression
  • Silicone Spark Plug Boots
  • 550 Degree Double Silicone Construction
  • Fiberglass Braid
  • Carbon/Graphite Core
  • Magnetic Suppression
  • Fiberglass/Kevlar Core
  • 500 Ohms Resistance
See More

Accel – 8Mm Super Stock Spiral Cust Bk (Part No.5048K)

8Mm Super Stock Spiral Cust Bk

from

$96.99
The traditional ACCEL combination of yellow wire and red spark plug boots has been added to these SuperStock Spiral Core 5000 Series wire sets, which feature color-matched wire and spark plug boots in blue, black, and red. With only 500 ohms/ft. of resistance, more ignition energy can reach the spark plug, producing a longer-lasting, hotter spark flame kernel. The results is higher performance through improved efficiency, quicker throttle response, and reduced emissions. This 8mm wire’s double silicone construction is rated to 550 degrees F. The high-gloss wire jacket resists moisture, chemicals, and heat extremes for longer life and great looks. The fiberglass braid adds greater pull strength and terminal retention, while the stainless steel spark plug terminals provide excellent long life, electrical conductivity, and corrosion resistance. Both universal and custom-fit applications are available for early and late model cars and trucks.

Product Features:
  • 500 Ohms/ft Of Resistance
  • 550 F Rated Silicone Jacket
  • Stainless Steel Plug Terminals
  • High RFI Suppression For Street And Strip Use
  • High-strength Fiberglass Braid Construction
  • 8mm High Gloss Silicone Jacket
  • 500 Ohms Resistance
See More

Accel – High Performance Ignition Module for GM HEI Distributors (Part No.35361)

High Performance Ignition Module for GM HEI Distributors

from

$69.99
This high performance HEI module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most GM HEI for V8 engines with the 4 pin module 1974 thru 1985

Product Features:
  • Fits Most Stock And Modified Distributors
  • Solid State Electronics
  • Dwell Control Circuit
See More

Spectre – Sbc Blk Off Plate W/Bolts (Part No.42463)

Sbc Blk Off Plate W/Bolts

from

$12.99
Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.

Product Features:
  • Necessary if switching to electric fuel pump
  • Includes block off plate gasket
  • Includes chrome mounting bolts with washers
  • Triple chrome plated
See More

Mr. Gasket – Fuel Pump Block-Off Plate (Part No.1515)

Fuel Pump Block-Off Plate

from

$12.99
This is what you need when changing your manual fuel pump to electric. It blocks the hole that remains when you remove the mechanical fuel pump from the engine to keep the oil inside. This plate is precision machined and is chrome plated.

Product Features:
  • Chrome Plated Steel
  • Comes With Gasket
See More

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Ultra Seal: Competition Screw-In Rocker Arm Studs

from

$94.99
Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Prevents Stud Flexing
  • Black Plated Finish
See More

B & M – Automatic Shifter, Quicksilver 4 Speed (Part No.80683)

Automatic Shifter, Quicksilver 4 Speed

from

$439.99
The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:
  • Universal Floor Mount Application
  • Base Trimmed For Custom Fit
  • Cable Operated
  • Quick Installation
  • Accurate Shifting
See More

Upgrade your 1978 Checker Marathon with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1978 Checker Marathon, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Checker or enhancing its overall performance, Performance and Racing Products are key to keeping your Marathon functioning at its best. At Advance Auto Parts, we offer a wide selection of 57 Performance and Racing Products for the 1978 Checker Marathon, designed to meet your needs without breaking the bank. From Performance Fuel System replacements to Performance Exhaust Products upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1978 Checker Marathon at great prices. Our Performance and Racing Products inventory for this model ranges from just $7.69 to $825.99, with an average price of $243.76. Our 57 Performance and Racing Products in stock come from 8 trusted brands, so you’re sure to find the right part for your 1978 Checker Marathon without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1978 Checker Marathon, we stock popular OEM and aftermarket Performance and Racing Products from top names like Edelbrock, Mr. Gasket, FEL-PRO Performance, and more. Edelbrock Performance and Racing Products start at just $35.99 and boast an impressive 4 stars average rating from customers. Mr. Gasket and FEL-PRO Performance also bring quality to the table, with Performance and Racing Products available starting at $12.99, and at an average 4 stars rating. With 177 customer reviews and counting, our 1978 Checker Marathon Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Fluids and Chemicals and more to make sure your 1978 Checker Marathon is always ready to roll. We’re committed to providing you with everything you need to keep your Marathon in top shape, all in one place. Start shopping confidently below for your 1978 Checker Marathon!

Best-Selling Performance Fuel Systems for 1978 Checker Marathons

Enhance the driving experience in your Checker with 12 quality Performance Fuel System components, starting at $12.99.

Mr. Gasket – Fuel Pump Block-Off Plate (Part No.1515)

Fuel Pump Block-Off Plate

from

$12.99
This is what you need when changing your manual fuel pump to electric. It blocks the hole that remains when you remove the mechanical fuel pump from the engine to keep the oil inside. This plate is precision machined and is chrome plated.

Product Features:
  • Chrome Plated Steel
  • Comes With Gasket
See More

Edelbrock – Performer 1411 Carburetor: 750 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1411)

Performer 1411 Carburetor: 750 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$494.99
The Edelbrock 1411 Performer Series 750 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – CARBURETOR (Part No.14054)

CARBURETOR

from

$488.99
Product Features:
  • EnduraShine Finish
  • GM/AMC-Style Throttle Linkage
  • Can Add Electric Choke PN[1478]
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$428.99
The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)

Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$451.99
The Edelbrock 1407 Performer Series 750 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Spectre – Sbc Blk Off Plate W/Bolts (Part No.42463)

Sbc Blk Off Plate W/Bolts

from

$12.99
Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.

Product Features:
  • Necessary if switching to electric fuel pump
  • Includes block off plate gasket
  • Includes chrome mounting bolts with washers
  • Triple chrome plated
See More

Edelbrock – Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1400)

Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$498.99
The Edelbrock 1400 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Electric Choke Installed from Factory
  • Smooth Secondary Transition
  • Includes Only Timed Vacuum Port
  • Includes EGR ; Fuel Vapor Outlet
See More

Edelbrock – CARBURETOR (Part No.14064)

CARBURETOR

from

$541.99
Product Features:
  • EnduraShine Finish
  • GM/AMC-Style Throttle Linkage
  • Electric Choke Installed from Factory
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1412)

Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$538.99
The Edelbrock 1412 Performer Series 800 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1412 Performer Series 800 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation. Dyno tests proved that the EPS 800 carb outperformed a Holley #3310 carb out-of-the-box by 26 ft-lbs. of torque and 22 hp on a small-block Chevy engine equipped with an Edelbrock Performer RPM power package

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
  • Can Easily Calibrate with Rods and Jets
See More

Edelbrock – Reman Thunder AVS Carb #18129 800 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.18129)

Reman Thunder AVS Carb #18129 800 CFM With Manual Choke, Satin Finish (Non-EGR)

from

$413.99
Product Features:
  • Satin Finish
  • 4 Barrel
  • Aluminum Body Material
  • Manual Choke Type
  • 800 cfm Maximum Flow Rating
See More

Edelbrock – Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9907)

Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR)

from

$407.99
Product Features:
  • Satin Finish
  • 4 Barrel
  • Annular Booster Type
  • Manual Choke Type
  • 750 cfm Maximum Flow Rating
See More

Most Popular 1978 Checker Marathon Performance Exhaust Products

Customize your Checker with 2 Performance Exhaust Products products like Performance Exhaust Manifold Gaskets, all priced under $34.49.

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1444)

Exhaust Manifold Gasket Set

from

$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1448)

Exhaust Manifold Gasket Set

from

$34.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Top Picks for 1978 Checker Marathon Performance Transmissions

Upgrade Checker Marathons with top-quality Performance Transmissions parts, including 2 OEM and aftermarket selections for your 1978 model.

B & M – Transpak For 65-87 TH400 Transmission (Part No.20228)

Transpak For 65-87 TH400 Transmission

from

$141.99
The B&M Transpak has all the features in the Shift Improver Kit, plus it provides additional driver manual control. Retain full automatic features and standard shift points with selector in Drive.

Product Features:
  • Recalibrate Auto. Transmission
  • Optimum Performance
  • Select Your App. Mode
  • Improves Transmission Life
  • Trans. Removal Not Required
  • Downshift At Any Speed
  • Great For Trailer Towing
  • For Heavy Loads Driving Downhill
See More

FAG US – CUP (Part No.LM48510)

CUP

from

$7.69
CUP

In-Demand Performance Ignition Products for 1978 Checker Marathons

Select from 4 premium Performance Ignition Products parts for your 1978 Checker Marathon, with prices ranging from $69.99 to $122.99.

Accel – High Energy Ignition Coil for GM HEI – 1973-1991 (Part No.140003)

High Energy Ignition Coil for GM HEI - 1973-1991

from

$100.99
Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:
  • 10-15% More Energy
  • Direct Plug In Replacement Direct OE Fit
  • Advanced Bobbin Technology
  • Highly Specialized Silicone Magnetic Steel Cores
  • Standard Motor Products SMP Dr-31
  • MSD 8225
See More

Accel – 8Mm Super Stock Spiral Cust Bk (Part No.5048K)

8Mm Super Stock Spiral Cust Bk

from

$96.99
The traditional ACCEL combination of yellow wire and red spark plug boots has been added to these SuperStock Spiral Core 5000 Series wire sets, which feature color-matched wire and spark plug boots in blue, black, and red. With only 500 ohms/ft. of resistance, more ignition energy can reach the spark plug, producing a longer-lasting, hotter spark flame kernel. The results is higher performance through improved efficiency, quicker throttle response, and reduced emissions. This 8mm wire’s double silicone construction is rated to 550 degrees F. The high-gloss wire jacket resists moisture, chemicals, and heat extremes for longer life and great looks. The fiberglass braid adds greater pull strength and terminal retention, while the stainless steel spark plug terminals provide excellent long life, electrical conductivity, and corrosion resistance. Both universal and custom-fit applications are available for early and late model cars and trucks.

Product Features:
  • 500 Ohms/ft Of Resistance
  • 550 F Rated Silicone Jacket
  • Stainless Steel Plug Terminals
  • High RFI Suppression For Street And Strip Use
  • High-strength Fiberglass Braid Construction
  • 8mm High Gloss Silicone Jacket
  • 500 Ohms Resistance
See More

Accel – High Performance Ignition Module for GM HEI Distributors (Part No.35361)

High Performance Ignition Module for GM HEI Distributors

from

$69.99
This high performance HEI module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most GM HEI for V8 engines with the 4 pin module 1974 thru 1985

Product Features:
  • Fits Most Stock And Modified Distributors
  • Solid State Electronics
  • Dwell Control Circuit
See More

Accel – Custom Fit Spark Plug Wire Set (Part No.8848)

Custom Fit Spark Plug Wire Set

from

$122.99
These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:
  • 8.8mm Graphite Suppression
  • Silicone Spark Plug Boots
  • 550 Degree Double Silicone Construction
  • Fiberglass Braid
  • Carbon/Graphite Core
  • Magnetic Suppression
  • Fiberglass/Kevlar Core
  • 500 Ohms Resistance
See More

Most Sold 1978 Checker Marathon Performance Engines

Explore our best-selling Checker parts for the 1978 Marathon among 36 OEM and aftermarket options starting from $20.29.

Edelbrock – Performer EPS Intake Manifold for 1955-86 Small-Block Chevy (Part No.2701)

Performer EPS Intake Manifold for 1955-86 Small-Block Chevy

from

$195.99


Product Features:
  • Maximizes Performance with Edelbrock Carburetors
  • Runners Tuned to Match Square Bore Carburetor
  • Maximizes Peak Torque Around 3500 RPM
  • Excellent Throttle Response and Mid-Range Power
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Prod. +5 HP and +9 ft/lbs. of Torque Over PN[2101]
See More

FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1003)

Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts

from

$39.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1004)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$52.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Engine Valve Cover Gasket Set

from

$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

from

$151.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Non-Rotator Style: Dyno Tested and Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

FEL-PRO Performance – PERFORMANCE VALVE COVER GASKET SET (Part No.1602)

PERFORMANCE VALVE COVER GASKET SET

from

$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Die cut silicone rubber gaskets conform to out-of-flat covers
  • Great for on-again/off-again situations
  • Not intended for use in emission controlled vehicles.
See More

B & M – Tork Master 3000 (Part No.20402)

Tork Master 3000

from

$499.99
Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
  • Washer Between Turbine and Cover
See More

B & M – Tork Master 2400 (Part No.20404)

Tork Master 2400

from

$339.99
Torque Converter – Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Edelbrock – Valve Cover Gasket Set for Chevrolet (Part No.7549)

Valve Cover Gasket Set for Chevrolet

from

$35.99
Product Features:
  • Valve Cover Gasket
See More

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

from

$111.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1803)

Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set

from

$26.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1010)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$39.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

from

$65.99
Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1640)

Engine Valve Cover Gasket Set

from

$22.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1819)

PERFORMANCE OIL PAN GASKET SET

from

$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Engine Timing Cover Gasket

from

$20.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Steel core gasket construction
  • Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Performer Small-Block Chevy Intake Manifold for Street Performance (Part No.3701)

Performer Small-Block Chevy Intake Manifold for Street Performance

from

$339.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 Deg Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
  • Accepts Late-Model Choke; Waterneck; and HEI
  • Accepts A/C And Alternator
  • Accepts Exhaust Heated Chokes and Accepts EGR
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1025)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$72.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)

Performance Torque Converter for GM TH400, 350, & 375 Transmissions

from

$299.99
Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5799G)

Ultra Seal: Head Gasket

from

$68.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.130 inch, Compressed thickness 0.055 inch

Product Features:
  • Five layer (graphite core/perforated steel outer layers) composite construction
  • Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
  • Provides excellent stability, compressibility and high temperature endurance
  • Coated with high temperature silicone to ensure sealing of engine fluids
  • Will not brinell (indent) aluminum cylinder heads
  • For high performance street, drag race and oval track use
  • Compatible w/High Octane Fuel
  • Compatible With Exotic Fuel
See More

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5780G)

Ultra Seal: Head Gasket

from

$64.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 3.870 inch, Compressed thickness 0.028 inch

Product Features:
  • Five layer (graphite core/perforated steel outer layers) composite construction
  • Graphite core has excellent thermo-conductivity-transfers heat away from hot spots in head preventing gasket burn-out
  • Provides excellent stability, compressibility and high temperature endurance
  • Coated with high temperature silicone to ensure sealing of engine fluids
  • Will not brinell (indent) aluminum cylinder heads
  • For high performance street, drag race and oval track use
  • Compatible w/High Octane Fuel
  • Compatible With Exotic Fuel
See More

Edelbrock – Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy (Part No.2703)

Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy

from

$322.99
Edelbrock part #2703 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thro

Product Features:
  • Idle-5500 RPM Range
  • Dual Plane Type-4150 Style Flange
  • 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
  • Satin Finish
  • Non-EGR W/ Oil Fill Tube
See More

Competition Cams – CAMSHAFT, SBC 295 BIG MUTHA THUMPR HYDRAULIC 1 EA (Part No.12-602-4)

CAMSHAFT, SBC 295 BIG MUTHA THUMPR HYDRAULIC 1 EA

from

$529.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Competition Cams – CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA (Part No.12-250-3)

CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA

from

$258.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Ultra Seal: Competition Screw-In Rocker Arm Studs

from

$94.99
Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Prevents Stud Flexing
  • Black Plated Finish
See More

B & M – Holeshot 3600 (Part No.20425)

Holeshot 3600

from

$825.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
  • Dual Pattern Drive Lugs
  • New Turbine Hub
  • New Springs/Rollers In Stator
See More

B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)

Torque Converter, Nitrous Holeshot 3600

from

$665.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:
  • 3400-3800 RPM
  • Small And Big Blocks
  • Serious Performance
  • Furnace Brazed
  • Fully Balanced
See More

Edelbrock – Performer RPM AIR-Gap Small Block Chevy Black Intake Manifold (Part No.75013)

Performer RPM AIR-Gap Small Block Chevy Black Intake Manifold

from

$525.99
Edelbrock part #75013 RPM Air-Gap RPM intake manifold is designed for 1955-86 262-400 c.i.d. Chevrolet V8’s. The award-winning RPM Air-Gap intake manifold incorporates the same race-winning technology that’s used on our Victor Series competition intakes.

Product Features:
  • 1500-6500 RPM Range
  • Dual Plane Type-4150 Style Flange
  • 4.2 in. Front Height, 4.72 in. Center Height, 5.25 in. Rear Height
  • Black Powder Coated Finish
  • Non-EGR
See More

Competition Cams – CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA (Part No.12-601-8)

CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA

from

$522.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

B & M – Holeshot 2400 (Part No.20412)

Holeshot 2400

from

$499.99
HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

Edelbrock – Performer EPS Manifold w/Oil Fill Tube for Small-Block Chevy, Black Finish (Part No.27033)

Performer EPS Manifold w/Oil Fill Tube for Small-Block Chevy, Black Finish

from

$445.99
Edelbrock part #27033 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thr

Product Features:
  • Idle-5500 RPM Range
  • Dual Plane Type-4150 Style Flange
  • 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
  • Black Powder Coated Finish
  • Non-EGR W/ Oil Fill Tube
See More

Edelbrock – Performer Intake Manifold Small-Block Chevy (Part No.3706)

Performer Intake Manifold Small-Block Chevy

from

$381.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 Deg Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
  • Accepts Late-Model Choke; Waterneck; and HEI
  • Accepts A/C And Alternator
  • Accepts Exhaust Heated Chokes and Accepts EGR
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5894)

Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

from

$147.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Dyno Tested And Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

Edelbrock – Cylinder Head Gasket Set for Chevrolet (Part No.7310)

Cylinder Head Gasket Set for Chevrolet

from

$58.99
Product Features:
  • 4.125 in. Cylinder Bore Diameter
  • 0.039 in. Thickness
  • 8.7cc Volume
  • Charcoal Color
  • Two Piece Configuration
See More

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)

PERFORMANCE REAR MAIN SEAL SET

from

$36.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
  • Not intended for use in emission controlled vehicles.
See More

Top-Rated Performance and Racing Products Brands For Your 1978 Checker Marathon

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1978 Checker Marathons. Below you’ll find some of our best rated Performance and Racing Products from Edelbrock, Mr. Gasket, and FEL-PRO Performance, and more. Performance and Racing Products from these brands that fit a 1978 Marathon start at just $12.99 and are rated as high as 4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular Edelbrock 1978 Checker Marathon Performance and Racing Products

When it comes to maintaining or upgrading your 1978 Checker Marathon, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Edelbrock ticks all of those boxes. We offer a wide selection of Edelbrock Performance and Racing Products, specifically designed for the 1978 Checker Marathon. With over 22 Edelbrock brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $35.99, with an average price of just $338.54. Plus, with over 88 customer reviews and an average rating of 4 stars, you can trust that our Edelbrock Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads
from
$65.99
This product is not rated

Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

“”

Performer Small-Block Chevy Intake Manifold for Street Performance
from
$339.99
This product is not rated

Performer Small-Block Chevy Intake Manifold for Street Performance

“”

Popular Mr. Gasket 1978 Checker Marathon Performance and Racing Products

Mr. Gasket auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1978 Checker Marathon owner should feel confident when installing genuine Mr. Gasket parts in their vehicle. To ensure the best fit and performance for your 1978 Marathon, Advance Auto Parts carries a full inventory of 5 Mr. Gasket Performance and Racing Products. Plus you will be keeping your Checker in peak condition while saving money because prices on these Mr. Gasket Performance and Racing Products range from $12.99 to $94.99, plus, with more than 26 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

Ultra Seal: Head Gasket
from
$64.99
This product is not rated

Ultra Seal: Head Gasket

“”

Ultra Seal: Head Gasket
from
$68.99
This product is not rated

Ultra Seal: Head Gasket

“”

Ultra Seal: Competition Screw-In Rocker Arm Studs
from
$94.99
This product is not rated

Ultra Seal: Competition Screw-In Rocker Arm Studs

“”

FAQs for 1978 Checker Marathon Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1978 Checker Marathons?

Out of 57 Performance and Racing Products that fit 1978 Checker Marathons, the following parts are the top sellers:

What’s the price range for 1978 Checker Marathon Performance and Racing Products?

Performance and Racing Product prices for the 1978 Checker Marathon start at $7.69 and go up to $825.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1978 Checker Marathon?

The average price for Performance and Racing Products for the 1978 Checker Marathon is $243.76. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Checker Marathon model years?

Yes, we currently carry Performance and Racing Products for 18 model years of Checker Marathons between 1961 and 1982. Performance and Racing Products are bought most frequently for the following model years: 1982, 1981, 1980, 1979, 1977, 1976, 1975, 1974, and 1973.

What are the cheapest Performance and Racing Products for my 1978 Checker Marathon?

The cheapest 1978 Checker Marathon Performance and Racing Products we carry in stock are:

What are the top-rated Performance and Racing Products that fit the 1978 Checker Marathon?

Out of 177 reviews by customers, our 1978 Checker Marathon Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1978 Checker Marathon and their top-rated products:

What types of Performance and Racing Products do you sell for my 1978 Checker Marathon?

Can I get help with 1978 Checker Marathon Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Checker Performance and Racing Products and more.

What is your return policy for Checker Marathon Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Checker Marathon Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.